Eiki Projector Lc Wip3000 User Manual

							29
MENU
Advanced Menu
LOGO SETTING
This function allows you 
to customize the start-up 
logo. 
In order to access 
this page PIN code is 
required.
 
Item Selection Description
LOGO MODEDEFAULT
USER
OFFSelect Mode( ► cursor button)
The factory logo.
The image you captured.
The blank image. You can select color with background 
function.
LOGO
CAPTUREEXECUTE Start to capture the image.(PC mode only)
BACKGROUNDBLACK
BLUE
WHITESet background color.
LOGO SIZEORIGINAL
FULLDisplay the captured image in original size and put in the 
center of the screen.
Expand the image to full screen. 
						

							30
MENU
NOTE  ►You can capture an image only in computer mode.
  ►The area that can be captured is 512 x 384 dots.
Advanced Menu
Logo Capture
How to use this function?
   Select Logo Capture item in the logo 
setting menu, then press ► button.
   Red frame will appear to select captures 
area.
   Use 4 direction buttons to adjust the 
position of the frame.
   Press "MENU" to start capturing and 
display a dialog.

Image

Logo Capture In Progress. 
						

							31
MENU
Presentation Menu
Step:
1.    Use the ▲ /▼buttons 
to select an item.
2.    Use the ◄ / ► buttons 
to select an item or 
adjust the value.
Item Selection Description
AUTO CEILING OFF / ONAutomatically invert the image when the projector is turned 
upside down, i.e. when the projector is mounted on the 
ceiling.
FRONT EXECUTE Normal projection mode.
CEILING EXECUTEMirror the image vertically, only for the projector mounted 
upside down.
REAR EXECUTEMirror the image horizontally, only for projecting onto rear 
projection screen.
CEILING AND 
REAREXECUTEMirror the image horizontally and vertically. Projecting onto 
a rear projection screen while projector is upside down.
LAMP MODEPOWERFUL /
NORMALSwitch lamp mode between normal or ECO mode.
LAMP Show lamp use time.
RESET LAMP 
TIMEREXECUTEAfter changing a new lamp, execute this function to reset 
the lamp timer.
Power
Management15/30/60/off
MinitesSet power off time after detecting no signal.  
						

							32
MENU
NOTE
►  The replacement warning message is set to appear after about 2500 hours of lamp use in order 
to maintain the initial brightness. When replacement message appears, replace the lamp with a 
new one as soon as possible, even if the lamp is still workable.
Presentation Menu
Reset Lamp Timer
The lamp timer is the time counted after the last resetting. The usage time of the lamp is 
shown in the PRESENTATION Menu. Select the “RESET LAMP TIMER” if the lamp 
timer is required to reset. The dialog of “Reset Lamp Timer ?” is shown on the screen 
as below. To reset the lamp time, select “yes” of Lamp Reset and push the button on the 
top cabinet. 
						

							33
MENU
Security Menu
Step:
1.   Use the ▲ /▼buttons to 
select an item.
2.   Use the ◄ / ► buttons to 
select an item or adjust the 
value.
Item Selection Description
PIN LOCK 
PROTECTIONOFF
ON 1
ON 2OFF:    Turn off PIN lock protection.
ON 1:  After plugging in AC power, you need to key in PIN 
code at the first time of use. If the AC power stays 
unplugged, you do not need to key in PIN code next 
time when you use the projector.
ON 2:  You need to key in PIN code every time when you 
turn on the projector.
 CAUTION:
Once the PIN code had been set, the projector cannot be 
used unless you enter the correct PIN code.
 
MODIFY PIN EXECUTE1. Press " MENU " on the projector or remote control.
2.  Use the ► button to select the MODIFY PIN item in the 
SECURITY category.
3.  Press the ► button to change PIN LOCK PROTECTION 
mode.
4. Please enter the original PIN code.
    (a)  If the PIN is correct, system will allow you to change 
a new PIN code.
    (b)  If the PIN is incorrect, a " Code Error " message will appear.
5. Please enter a new PIN code. And then enter again to confirm.
NOTE:
(1)  To change the PIN lock protection state, you must 
enter the PIN code first.
(2) Please enter: 0000 for first-time use.
(3)  To avoid unnecessary trouble, if you activate the [PIN 
Lock Protection], it is highly recommended that you 
write down the PIN code and store it in a safe place. 
						

							34
MENU
Security Menu
Step:
1.   Use the ▲ /▼buttons to 
select an item.
2.   Use the ◄ / ► buttons to 
select an item or adjust the 
value.
Item Selection Description
FILTER TIMER Show the filter use time.
RESET FILTER
TIMEREXECUTE Reset the filter timer after cleaning / changing filter.
FILTER COUNTER500 hours
800 hours
1000 hoursSelect (500 / 800 / 1000 hours) depending on the 
environment.(default : 500 hours). Please see next page.
MAC ADDR.For LAN control module, "MAC ADDR." will be shown in 
"SECURITY" Menu. 
MAC address stands for unique Media Access Control 
address of LAN control module and displays with six 
groups of two hexadecimal digits.
CLOSED CAPTIONOFF(Default)
C.C1
C.C2
C.C3
C.C4
T1
T2
T3
T4The Closed Caption function intimates the sound effects, 
dialogue, and narration in the content of the television 
program or video source.
Caption (C.C1~C.C4) : Display closed caption Text 
(T1~T4) : Display text data, which is for additional 
information such as news reports or a TV program guide.
NOTE :  This function is available only in Video / S-Video 
source.
LAN MODULE OFF
ONSelect ON/OFF to turn on/off LAN control feature.
LAN SETTING EXECUTEEnter LAN SETTING to set up projector network 
configuration. 
						

							35
MENU
Security Menu
Step:
1.   Use the ▲ /▼buttons to 
select an item.
2.   Use the ◄ / ► buttons to 
select an item or adjust the 
value.
Item Selection Description
PROJECTOR 
NAMEDefault is 
ProjectorProjector network setting display which shows bits that can 
be recognized by ASCII.
DHCP OFF / ONWhen setting ON, projector's IP address will be assigned by 
DHCP server automatically. When setting OFF, you can use 
remote control to do setting manually.
IPKey in IP address manually. Press "ENTER" to do digit 
setting. When appears, press 
▲ /▼ to adjust value. When 
finishing value adjustment, press MENU to exit.
MASKEnter MASK address manually. Press "ENTER" to do digit 
setting. When appears, press ▲ /▼ to adjust value. When 
finishing value adjustment, press MENU to exit.
GATEWAYEnter GATEWAY address manually. Press "ENTER" to do 
digit setting. When appears, press ▲ /▼ to adjust value. 
When finishing value adjustment, press MENU to exit. 
						

							36
MENU
NOTE
► Please reset the Filter time only when you replace the filter.
Auto Filter Alert
Auto Filter Alert in SECURITY category shows the air filter use time and alerts user to change 
filter. When the operating time reaches the set time, a warning message will appear on the screen to 
remind user of filter cleaning /replacing.
Filter Replace...
Filter has been used for more than 500 hours. 
						

							37
MENU
PIN Key In Operation
When the projector is turned on and the 
PIN LOCK PROTECTION is set to [ON], 
the image will show as on the right side.
1.  Press the MENU button on the projector 
or remote control. Enter PIN code by 
keypad or remote control.
2.   How to enter a PIN code? 
You can use control panel or remote 
control.
(1) Press ◄ button: Select the [ 1 ]
(2) Press ▲ button: Select the [ 2 ]
(3) Press ► button: Select the [ 3 ]
(4) Press ▼ button: Select the [ Enter ] to move to next row.(4~6,7~9, 
~OK)
(5)  Press 
 (backspace) item: 
In case you enter a wrong digit, select  to delete the wrong digit you entered.
(6)  Press 
 item: 
Once all four digits of the PIN are entered, select  to confirm.
NOTE
(1) Please enter: 0000 for first-time use.
(2)  If the PIN is incorrect, a "Enter new code" message will be shown. Please try again. If the PIN 
code input is incorrect for three times, a warning message will show up and the  projector will 
shut itself down in 30 seconds.
(3)  If you have no idea about the PIN, please contact your dealer for help.
Refer to photo below to enter a sequence of PIN code by touch keypad or remote control buttons.
TOUCH KEYPAD
REMOTE CONTROLThe touch keypad and remote control 
buttons to enter a sequence of PIN code is 
like the photo below. 
						

							Network Control Software Application
38
Network Control Software Application
LAN
Procedure to utilize this function
Network Control is provided in visual interface, it can help user to monitor and manage the 
projector(s) status in the local area network.
1.  Register the projector(s) which needs to be controlled. 
" Auto search " can help you to seek the projector(s) source easily. 
After registering in the work group, you can start to control the projector.
2.  Group the projector(s) into different sections. 
You can monitor the status easily by the sort of group name function in the network.
3.   
  Monitor the status for each projector. 
a.You can manage and change the monitoring content by System Parameter Setting. 
b. The Lamp timer, filter working time or system warning feedback etc. can be known 
by checking the status for projector(s).
4.   Control the booked projector(s). 
  The status can be refreshed and acquired by monitoring functions; you can also operate the function 
easily by   Network Control.
NOTE:
To monitor and control the projector(including stand-by mode), the following conditions need to be 
ready:
(1) Projector should already be powered on.
(2) Projector is connected to network.
(3)  LED light of the projector network port shows normal. (Green light on, Orange twinkle)
*  Stand-by mode indictor: Green LED (Power) on the projector’s touch keypad  flashes.