Eiki Projector Lc Wb42n User Manual

51

Off

Capture
Capture
This	function	enables	you	to	capture	an	image	being	
projected	to	use	it	for	a	starting-up	display	or	interval	of	
presentations.
Select	Capture 	and	press	the	SELECT 	button.		
A 	confirmation	box	appears	and	select	 yes 	to	capture	the	
projected	image.
After	capturing	the	projected	image,	go	to	the	Logo	select	
function	and	set	it	to	
User .	Then	the	captured	image	will	be	
displayed	the	next	time	you	turn	on	the	projector	or	when	
you	press	the	NO	SHOW	button	(see	page	29)....

52

Setting
Enter	a	Logo	PIN	code
Use	the	Point	▲▼	buttons	 to	enter	 a	number.	 Press	the	
Point	
►	 button	 to	fix	 the	 number	 and	move	 the	red	 frame	
pointer 	to 	the 	next 	box. 	The 	number 	changes 	to 	
.	 If	
you	 fixed	 an	incorrect	 number,	use	the	Point	
◄	button	 to	
move	 the	pointer	 to	the	 number	 you	want	 to	correct,	 and	
then	enter	the	correct	number.
Repeat	this	step	to	complete	entering	a	four-digit	
number.
After	entering	the	four-digit	number,	move	the	pointer	to	
Set ....

53

Setting
Ceiling	
Rear	
Ceiling
When	this 	function 	is 	set 	to 	On ,	 the 	picture 	will 	be 	top/
bottom 	and 	left/right 	reversed. 	This 	function 	is 	used 	to	
project	the	image	from	a	ceiling-mounted	projector.
Rear
When	 this	function	 is	set	 to	On,	the	 picture	 will	be	left/right	
reversed. 	This 	function 	is 	used 	to 	project 	the 	image 	from	
rear	of	the	screen.
HDMI	setup
HDMI	setup
This	function	is	only	used	for	HDMI	input	source.
		Image
														Normal :									When	the...

54

Setting
Arrow
PointerPointer
You	can	emphasize	a	part	of	the	projected	image	with	this	
function.	Use	the	Point	▲▼	buttons	to	choose	Spotlight	
(Large,	Middle 	or	Small)	,	Arrow ,	Finger 	or	Dot	and	press	
the	SELECT 	button.	See	"Pointer	Function"	on	page	14.
Standby	mode
This	function	is	available	when	operating	the	projector	via	
network.
	Normal	...... 	Supply	 the	power	 to	the	 network	 function	 even	
after	turning	off	the	projector.	 You	can	turn	on/
off	the	projector	via	network,...

55

Setting
Picture	in	Picture
Picture	in	Picture
Note:
•	When	the	input	signal(s)	is/are	incompatible,	X 	mark	will
		be	displayed	on	the	Main/Sub	picture.
• 	When	the	sub	picture	is	set	to	the	same	signal	as	the	main
		picture,	
X 	mark	will	be	displayed.
		•	 Subpicture	position 	and	Subpicture	size 	are	only	used		
				for	 P	in	P
.
Subpicture size
Note:
•	When	 P	in	P 	or	P	by	P 	is	set,	 Total	dots	 is	
		disabled	in	the	PC	adjust	menu.	
• 	In	Picture	in	Picture	mode,	the	Freeze	function	
		is...

56

Power	management
Timer	left	before	Lamp	is	off.
Power	managementFor	reducing	power	consumption	as	well	as	maintaining	
the	lamp	life,	the	Power	management	function	turns	off	the	
projection	lamp	when	the	projector	is	not	operated	for	a	
certain	period.
Select	one	of	the	following	options:
Ready	.................. 	When	the	lamp	has	been	fully	cooled	
down,	the	POWER	indicator	changes	
to	green	blinking.	In	this	condition,	the	
projection	lamp	will	be	turned	on	if	the	
input	signal	is	reconnected	or...

57

Setting
On	start
When	this	function	is	set	to	On,	the	projector	will	be	
automatically	turned	on	just	by	connecting	the	 AC	power	
cord	to	a	wall	outlet.	
Note:
	 Be	sure	to	turn	off	the	projector	properly	(see	"Turning	Off	 the	Projector"	on	page	23).	If	the	projector	is	turned	off	
in	the	incorrect	sequence,	the	On	start	function	does	not	
work	properly.
Closed	caption
Closed	Caption	is	a	function	that	displays	the	audio	portion
of	a	 TV	program	as	text	on	the	screen.	If	the	input	signal...

58

Remote	control
Lamp	control	
Remote	control
The	eight	different	remote	control	codes	(Code	1-Code	8 )	
are	assigned	to	the	projector;	the	factory-set,	initial	code	
( Code	1 )	and	the	other	seven	codes	( Code	2	to	Code	8 ).	
The	same	code	should	set	on	both	the	projector	and	the	
remote	control.	For	example,	operating	the	projector	in	
Code	7 ,	the	remote	control	code	also	must	be	switched	to	
Code	7
.
	 To	change	the	code	for	the	projector
	 Select	a	remote	control	code	in	this	Setting	Menu.
	 To...

59

Setting
Key	lock
Key	lockSecurity	(Key	lock	and	PIN	code	lock)
PIN	code	lock
This	function	locks	the	top	control	and	remote	control	
buttons	to	prevent	operation	by	unauthorized	persons.	.....
	Unlocked.
	 ..... 	Lock	the	operation	of	the	top	control.	 To	
unlock,	use	the	remote	control.
	 ..... 	Lock	the	operation	of	the	remote	control.				
To	unlock,	use	the	top	control.
If	 the	 top	control	 accidentally	 becomes	locked	and	you	do	
not	 have	 the	remote	 control	nearby	 or	there	 is	something...

60

Setting
Use	the	Point	▲▼	buttons	to	select	Off,	On1 	or	On2.	
Press	the	SELECT 	button	to	close	the	dialog	box.
Change	the	PIN	code	lock	setting Enter	a	PIN	code
Use	the	Point	▲▼		buttons	to	enter	a	number.	Press	the	
Point	
►	button	to	fix	the	number	and	move	the	red	frame	
pointer	to	the	next	box.	 The	number	changes	to	
.	If	
you	fixed	an	incorrect	number,	use	the	Point	
◄	button	to	
move	the	pointer	to	the	number	you	want	to	correct,	and	
then	enter	the	correct	number.
Repeat	this	step	to...