Eiki Projector Lc Wb42n User Manual

41

Video	Input
Choose	Computer	1	 by	pressing	the	INPUT 	button	on	the	top	control	or	press	the	COMPUTER	button	on	the	
remote	control;	choose	
HDMI 	by	pressing	the	INPUT 	button	on	the	top	control	or	press	the	HDMI	button	on	the	
remote	control.	
Before	using	these	buttons,	correct	input	source	should	be	selected	through	Menu	operation	as	described	
below.
1
Input	Menu
2Use	the	Point	▲▼	buttons	to	select	 Computer	1	and	
then	press	the	Point	
►	button;	use	the	Point	▲▼	
buttons	to	select	
HDMI ,	and...

42

Video	InputVideo	System	Selection
1AV	System	Menu	(Video	or	S-video)
AV	System	Menu	(Component)
2
If	the	projector	cannot	reproduce	proper	video	image,	
select	a	specific	broadcast	signal	format	from	among	
PAL,	
SECAM,	NTSC ,	NTSC	4 .43 ,	
PAL-M	and	PAL-N.
PAL/SECAM/NTSC/NTSC4 .43/PAL-M/PAL-N
The	projector	automatically	detects	an	incoming	video	
signal,	and	adjusts	itself	to	optimize	its	performance.
If	the	projector	cannot	reproduce	proper	video	image,	select	
a	specific	component	video	signal...

43

Image	Select	Menu
Select	the	desired	image	mode	 among	Dynamic,	Standard ,	
Cinema,	Blackboard	(Green) ,	Colorboard,	Image	1 ,	
Image	2 ,	Image	3 	and	Image	4 	by	pressing	the	IMAGE	
button	on	the	remote	control.
Standard
Picture	mode	adjusted	with	fine	tone.
Cinema
Blackboard	(Green)
Image	1–4
IMAGE	button
Dynamic
Cinema
Image	Mode	Selection	
Blackboard	(Green)
Dynamic
Standard
Remote	Control
IMAGE	button
Direct	Operation
For	viewing	pictures	in	a	bright	room.
Normal	picture	mode	preset	on	the...

44

Video	InputImage	 Adjustment
1
2
Press	the	Point	◄	button	to	decrease	the	contrast;	press	the	
Point	
►	button	to	increase	the	contrast	(from	0	to	63).
Press	the	Point	◄	button	to	decrease	the	brightness;	press		
the	Point	
►	button	to	increase	the	brightness	(from	0	to	63).
Contrast
Brightness
Press	the	Point	◄	button	to	lighten	red	tone;	press	the	Point	
►	button	to	deepen	red	tone	(from	0	to	63).
White	balance	(Red)
Press	the	Point	◄	button	to	lighten	green	tone;	press	the	
Point	
►	button	to...

45

Video	Input
Use	the 	Point 	◄►	buttons 	to 	adjust 	the 	gamma 	value 	to	
obtain	a	better	balance	of	contrast	(from	0	to	15).
Gamma
Press	the	Point	◄	button	to	decrease	the	sharpness	of	the	
image;	press	the	Point	
►	button	to	increase	the	sharpness	
of	the	image	(from	0	to	15).
Sharpness
An	interlaced	video	signal	can	be	displayed	in	progressive	
mode.	Select	one	of	the	following	options.
	Off 	.........	Disabled.
	L1 	.......... 	For	an	active	picture.
	L2	.......... 	For	a	still	picture.
	Film...

46

Video	Input
This	projector	has	the	picture	screen	resize	function,	which	enables	you	to	customize	the	image	size.
Normal
Screen	Size	Adjustment
Screen	Menu1
2
Provide	the	image	to	fit	the	screen	size	while	maintaining
the	aspect	ratio	of	input	signal.
Custom
Adjust	the	screen	scale	and	position	manually	with	this	
function.
Press	the	Point	►	button	at	
Custom 	and	the	Custom	is
displayed	on	the	screen,	you	can	use	the	Point	▲▼	buttons
to	choose	the	item	you	want	to	adjust.
	 Scale	H/V 	.............

47

HDMI setupTerminal                                                        Computer 2Pointer                                                          DotStandby mode                                               Eco

Language
The	language	used	in	the	On-Screen	Menu	is	available	in	
English,	German,	French,	Italian,	Spanish,	Portuguese ,	
Dutch,	Swedish,	Finnish,	Polish ,	Hungarian,	Romanian ,	
Russian,	Chinese,	Korean ,	japanese	 and	Thai.
Setting	Menu
Setting
Setting
HDMI setupTerminal...

48

Setting
Note:
	 •	Auto	Keystone 	corrects	vertical	distortion	only,	not	
correct	horizontal	distortion.
	 •	The	 Auto	Keystone 	function	cannot	work	when	the	
Ceiling	feature	is	set	On	in	the	Setting	menu	(p.53).
	 •	Perfect	correction	of	the	image	distortion	cannot	 be	ensured	with	the	 Auto	setup	function.	If	the	
distortion	is	not	corrected	properly	by	pressing	the	
AUTO	SETUP/CANCEL 	button,	adjust	manually	
by	pressing	the	KEYSTONE	button	on	the	remote	
control	or	selecting	
Keystone 	in	the...

49

Keystone
This	function	is	used	to	store	or	reset	the	keystone	
correction	when	the	AC	power	cord	is	unplugged.
	Store	....... 	Keep	the	keystone	correction	even	when	the	
AC	power	cord	is	unplugged.
	Reset 	....... 	Release	the	keystone	correction	when	the	 AC	
power	cord	is	unplugged.
To	correct	keystone	distortion,	press	the	SELECT 	button.	
Keystone	appears	on	the	screen.	Use	the	Point	▲▼	
buttons	to	correct	keystone	distortion	(p.26).
Background
Select	the	background	screen	for	when	no	input...

50

Setting
Logo	(Logo	and	Logo	PIN	code	lock	settings)
HDMI setupTerminal                                                        Computer 2Pointer                                                          DotStandby mode                                               Eco
Logo	select
This	function	allows	you	to	customize	the	screen	logo	with	
Logo	select,	
capture,	Logo	PIN	code	lock 	and	Logo	PIN	
code	change 	functions.
Note:
	 		When	
On 	is	selected	in	the	Logo	PIN	code	lock	function,	
Logo	select ,...