Eiki Projector Lc Wb200 User Manual

61
Maintenance and CleaningMaintenance and Cleaning
RECOMMENDATION	 We	recommend	avoiding	dusty/smoky	environments	when	you	operate	the	projector.		Usage	in	these	environments	may	cause	poor	image	quality. When using the projector under dusty or smoky conditions, dust may accumulate on a lens, LCD panels, or optical elements inside the projector degrading the quality of a projected image.  When the symptoms above are noticed, contact your authorized dealer or service center for proper cleaning.
Be sure...

62
Maintenance and Cleaning
Cleaning	the	Projector	Cabinet
Cleaning	the	Projection	Lens
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use a lens cleaning paper or commercially available air blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the lens.
Unplug the AC power cord before...

Maintenance and Cleaning
63
Maintenance and Cleaning
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.
For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury.
Allow a projector to...

64
Maintenance and Cleaning
This  projector  uses  a  high-pressure  lamp  which  must  be  handled  carefully  and properly.  Improper handling may result in accidents, injury, or create a fire hazard.
●  Lamp  life  may  differ  from  lamp  to  lamp  and  according  to  the  environment  of  use. There  is  no  guarantee  of  the  same  life  for  each  lamp.  Some  lamps  may  fail  or terminate their life in a shorter period of time than other similar lamp\
s.
●	 If the projector indicates that the...

Maintenance and Cleaning
65
	 Problem: – Solutions
 No power  – Plug the power cord of the projector into the AC outlet.     – See if the POWER indicator lights red.     –  Wait until the POWER indicator stops blinking to turn on the projector again. The projector can be turned on after the POWER indicator turns red. See page 18.    – Check the WARNING indicator. If the WARNING indicator lights       red, projector cannot be turned on. See page 70.     – Check the projection lamp. See page 63.     –...

66
Appendix
 No image  – Check the connection between your computer or video               equipment and the projector. See pages 14-16.    – See if the input signal is correctly output from your computer.            Some laptop computers may need to change the setting for                                                                monitor output when connect\
ing to a projector. See your            computer’s instruction manual for the setting.     – It takes about 30 seconds to display an image...

Appendix
67
Appendix
	 The	image	is	distorted	or	runs	off.			– Check PC adjust menu or Screen menu and adjust them.            See pages 29-30, 34-35.
	 PIN	code	dialog	box	appears													– PIN code lock is being set. Enter a PIN code (the “1234”     at start-up .                                              or number you have set). See pages 19, 55-56.
	 The	Remote	control	does        – Check the batteries.  not work .        – Make sure no obstruction is between the projector and...

68
Appendix
Menu	Tree
Computer	Input/HDMI/	Input/Video	Input
VolumeMuteOn/OffSound0-63
RGBComponent
RGBRGB(Scart)
Input
Video
Computer 1
Computer 2
MICOn/OffMIC gain0-63Standby MIC outOn/Off
Dynamic
CinemaBlackboard (Green)
Image 1
Image	selectStandard
ColorboardRed/Blue/Yellow/Green
Image 4
Real
InformationInput Source Information Display
LanguageSetting22 languages provided.
Blue/User/BlackOff /On/Countdown offLogo select
Ready
On/Off
Code 1–Code 2
BackgroundDisplayLogo
Power management 
Direct on...

Appendix
69
Appendix
HDMI	Input	/	Video	Input
Auto1080i1035i720p575p480p575i480i
0–630–63
Off
System	(2)
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
System	(3)
Image	AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15 0–15
Image 1Yes/No
OffNoise reductionL1L2
0–630–63
Image 4
L2L1
Film
Color temp.
MidLowXLow
UserHigh
SVGA 1Mode 1Mode 2 - - - -
Total dotsHorizontalVertical
Display area HDisplay area VReset
Image	AdjustContrastBrightnessColor temp.
Red
Gamma
Store...

70
Appendix
Check the indicators for projector condition.                                   
•	•	•	green•	•	•	red•	•	•	off
•	•	•	blinks	green.
 When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow.     When this indicator lights yellow, replace the projection lamp with a new one promptly. (p. 65)
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button to turn on the projector.
Projector ConditionPOWER...