Eiki Projector Lc Wb200 User Manual

Part Names and Functions
11
Part Names and Functions
Note:To ensure safe operation, please observe the following precautions:– Do not bend, drop or expose the remote control     to moisture or heat.– For cleaning, use a soft dry cloth. Do not apply    benzene, thinner, spray, or any chemical material.
Remote	control
⑦
⑭
⑩
㉑④
⑲
②
⑧
⑨
⑬
⑰
⑤
⑥
⑪
⑫
⑳
⑯
③
② AUTO	SET	button
Execute the setting of Auto setup (includes Input search, Auto PC adj. and Auto Keystone functions) in the setting menu. (pp.23, 45)
⑤...

12
Part Names and Functions
To ensure safe operation, please observe the following precautions :	 ●	Use	two	(2)	AAA	or	LR03	type	alkaline	batteries.	 ●	Always	replace	batteries	in	sets.	 ●	Do	not	use	a	new	battery	with	a	used	battery.	 ●	Avoid	contact	with	water	or	liquid.	 ●	Do	not	expose	the	remote	control	to	moisture	or	heat.	 ●	Do	not	drop	the	remote	control.	 ●	If	the	battery	has	leaked	on	the	remote	control,	carefully	wipe	the	case	clean	and	install	new			     batteries.	 ●	Risk	of	an	explosion	if...

Part Names and Functions
13
Positioning	the	Projector
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen.
Installation
Note:
	 •	 The	brightness	 in	the	 room	 has	a	great	 influence	 on	picture	 quality.	 It	is	 recommended	 to	limit	 ambient	 lighting	in order to obtain the best image.	 •	 All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
Adjustable	Feet
Projection angle can be adjusted up to 12.0 degrees with the...

14
Installation
Connecting to a Computer
Cables	used	for	connection	•	VGA	Cables	(Mini	D-sub	15	pin)	*•	Audio	Cable•	HDMI-DVI	cable(*One cable is supplied; other cables are not supplied with the project\
or.)
 Note:
	 •	When	the	MIC	function	is	set	to	Off in the Sound menu, the MIC function is disabled. (p. 24)	 •	When	MIC is set to On in Sound Menu, COMPUTER AUDIO IN 1, COMPUTER AUDIO IN 2 / MIC IN and AUDIO IN(L/R) terminals can be connected at the same time. At this time, COMPUTER AUDIO IN 2 terminal...

Installation
15
Installation
Connecting	to	Video	Equipment
Cables	used	for	connection		•	Video	and	Audio	Cable	(RCA 	x	3)	•	S-VIDEO	Cable	•	Audio	Cable	•	HDMI	Cable	(Cables are not supplied with the projector. )
 Note:
  When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available.
External Audio Equipment
Audio cable   (stereo)
VIDEOS-VIDEO
S-Video cable  Video and audio cable  
           Video and Audio Output
S-Video Output
AUDIO IN
Audio Input
AUDIO OUT (stereo)...

16
Installation
Connecting	to	Component	Video	and	RGB	(Scart)	Equipment
 Note:
	 •	When	the	AUDIO	OUT	is	plugged-in,	the	projector's	built-in	speaker	is	not	available.	 •	See	page	74	for	ordering	optional	cables.
External Audio Equipment
COMPUTERAUDIO IN 1 
Audio cable (stereo)
Audio cable (stereo)
Audio InputComponent Video Output(Y, Pb/Cb, Pr/Cr)RGB Scart 21-pin OutputAudio Output
Scart-VGA cable 
Component-VGA cable
AUDIO  OUT (stereo)
Component cable
COMPUTER IN 1/ COMPONENT IN 
Cables	used	for...

Installation
17
Installation
Connecting	the	AC	Power	Cord
This projector uses nominal input voltages of 100-240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.If you are not sure of the type of power being supplied, consult your authorized dealer or service center.Connect the projector with all peripheral...

18
The preparation display will disappear after 30 seconds.
(See page 54 for Lamp control status.)
Turning	On	the	Projector
Connect the projector’s AC power cord into an  AC  outlet.  The  POWER  indicator  lights red. Open the lens cap.
Press  the  ON/STAND-BY  button  on  the t o p   c o n t r o l   o r   o n   t h e   r e m o t e   c o n t r o l . The  POWER  indicator  lights  green  and t h e   c o o l i n g   f a n s   s t a r t   t o   o p e r a t e .   T h e preparation  display  appears  on  the...

19
Basic Operation
What	is	PIN	code?
PIN  (Personal  Identification  Number)  code  is  a security code that allows the person who knows it  to  operate  the  projector.  Setting  a  PIN  code prevents unauthorized use of the projector.
A  PIN  code  consists  of  a  four-digit  number. Refer to the PIN code lock function in the Setting Menu  on  pages  55-56  for  locking  operation  of the projector with your PIN code.
Enter	a	PIN	code
Use  the  Point ▲▼  buttons  to  enter  a  number. Press  the...

20
Basic Operation
TO	MAINTAIN	THE	LIFE	OF	THE	LAMP,	ONCE	YOU	TURN	THE	PROjECTOR	ON,	WAIT	 AT	LEAST	FIVE	MINUTES	BEFORE	TURNING	IT	OFF .
Power	off? disappears after 4 seconds.
Turning	Off	the	Projector
Press  the  ON/STAND-BY  button  on  the  top control or on the remote control, and Power off?	appears on the screen.
Press  the  ON/STAND-BY  button  again  to turn off the projector. The POWER indicator starts  to  blink  red,  and  the  cooling  fans keep  running.  (You  can  select  the  level  of...