Eiki Projector Lc Wb100 User Manual

61

Information
The	WARNING	indicator	shows	the	state	of	the	function	which	protects	the	projector.	Check	the	state	of	the	
WARNING	indicator	and	the	POWER	indicator	to	take	proper	maintenance.	
WARNING indicator
The projector is shut down and the WARNING 
indicator is blinking red .
When	the	temperature	inside	the	projector	reaches	a	
certain	level,	the	projector	will	be	automatically	shut	down	to	
protect	the	inside	of	the	projector.	The	POWER	indicator	is	
blinking	while	the	projector	is	being	cooled...

6

Turn	off	the	projector,	and	unplug	the	AC	power	cord	
from	the	 AC	outlet.
Turn	the	projector	over	and	remove	the	filters	.
1

Filter	prevents	dust	from	accumulating	on	the	optical	elements	inside	the	projector.	Should	the	filters	become	
clogged	with	dust	particles,	it	will	reduce	cooling	fans’ 	effectiveness	and	may	result	in	internal	heat	buildup	
and	adversely	affect	the	life	of	the	projector.	If	a	“Filter	warning”	icon	appears	on	the	screen,	clean	the	filters	
immediately.	Clean	the...

6

Cleaning the Projector Cabinet
Cleaning the Projection Lens
Unplug	the	AC	power	cord	before	cleaning.
Gently	wipe	the	projection	lens	with	a	cleaning	cloth	that	
contains	a	small	amount	of	non-abrasive	camera	lens	
cleaner,	or	use	a	lens	cleaning	paper	or	commercially	
available	air	blower	to	clean	the	lens.	
Avoid	using	an	excessive	amount	of	cleaner.	 Abrasive	
cleaners,	solvents,	or	other	harsh	chemicals	might	scratch	
the	surface	of	the	lens.
Unplug	the	 AC	power	cord	before	cleaning.
Gently...

64

When  the  projection  lamp  of  the  projector  reaches  its  end 
of  life,  the  Lamp  replacement  icon  appears  on  the  screen 
and  LAMP  REPLACE  indicator  lights  yellow.  Replace  the 
lamp  with  a  new  one  promptly.  The  timing  when  the  LAMP 
REPLACE  indicator  should  light  is  depending  on  the  lamp 
mode.
Follow these steps to replace the lamp.
For continued safety, replace with a lamp of the 
same type. Do not drop a lamp or touch a glass 
bulb! The glass can shatter and...

65

This	projector	uses	a	high-pressure	lamp	which	must	be	handled	carefully	and	properly.		
Improper	handling	may	result	in	accidents,	injury,	or	create	a	fire	hazard.
●	Lamp	 life	may	 differ	 from	lamp	 to	lamp	 and	according	 to	the	 environment	 of	use.	 There	 is	no	 guarantee	
of	 the	 same	 life	for	each	 lamp.	 Some	 lamps	 may	fail	or	terminate	 their	life	in	a	shorter	 period	of	time	
than	other	similar	lamps.
●	 If	 the	 projector	 indicates	 that	the	lamp	 should	 be	replaced,	 i.e.,	if	the...

66

 Problem:	 –	Solutions
  No power 	 –	Plug	the	power	cord	of	the	projector	into	the	AC	outlet.
	
	 	 –	See	if	the	POWER	indicator	lights	red.
	
	 	 –		
Wait	until	the	POWER	indicator	stops	blinking	to	turn	on	the	projector	
again.	 The	projector	can	be	turned	on	after	the	POWER	indicator	
turns	red.	See	page	18.
	 	 –	Check	the	WARNING	indicator.	If	the	WARNING	indicator	lights	red,																	
																																																																					projector	cannot	be	turned	on....

67

 No image	 –	Check	the	connection	between	your	computer	or	video	equipment		
	 	 	 and	the	projector.	See	pages	14-16.
	
	 	 –	See	if	the	input	signal	is	correctly	output	from	your	computer.	Some		
	 	 	 laptop	computers	may	need	to	change	the	setting	for	monitor	output		
	 	 			when	connecting	to	a	projector.	See	your	computer’s	instruction		
	 	 	 manual	for	the	setting.	
	
	 	 –	It	takes	about	30	seconds	to	display	an	image	after	turning	on	the		
	 	 	 projector.	See	page	18.
	 	 –		
Check	the...

68

 The image is distorted or runs off .  –	Check	PC adjustment	menu	or	Screen	and	adjust	them.		 	
	 	 			See	pages	31-32,	35-36.
  PIN code dialog box appears 	 –	PIN	code	lock	is	being	set.	Enter	a	PIN	code	(the	“1234”	or	numbers	
	at start-up . 	 	 you	have	set).	See	pages	19,	56-57.
  The Remote Control does 	–	Check	the	batteries.
	
	not work . 	 –	Make	sure	no	obstruction	is	between	the	projector	and	remote	 	
	 	 			control.
	
	 	 –	Make	sure	you	are	not	too	far	from	the	projector	when	using...

6

WARNING :
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If	problems	still	persist	after	following	all	operating	instructions,	contact	the	dealer	where	you	purchased	the	
projector	or	the	service	center.	Specify	the	model	number	and	explain	about	the	problem.	We	will	advise	you	
how	to	obtain	service.
This	symbol	 on	the	 nameplate	
m e a n s 	t h e 	p r o d u c t 	i s 	L i s t e d	
by	 Underwriters	 Laboratories	
I n c . 	 	I t	i s 	d e s i g n e d 	a n...

70

Menu Tree
SVGA	1Mode	1Mode	2	-	-	-	-
Total	dotsHorizontalVertical
Display	area	HDisplay	area	VReset
Dynamic
RealBlackboard	(Green)
Image	1Image	2Image	3
Image adjustContrastBrightnessColor	temp.
Red
Gamma
Store
0–630–63
Computer Input
PC adjust
Mode	1Mode	2Mode	3Mode	4Mode	5
Image select
0–63
0–15
Image	1Image	2Image	3Image	4
Yes/No
	*	Systems	displayed	in	the	System	Menu	vary	
depending	on	an	input	signal.
ResetYes/No
Sharpness0–15
Computer Input/Video Input
Sound
VolumeMuteOn/OffSound0–63...