Eiki Lc-Xip2600 Interactive Projector Owners Manual

Control Panel Window Introduction
48
Control Panel Window Introduction
		Power Control
IconName
Power on
Power off
		Input Source
IconName
Video
S-Video
Y, Pb, Pr / Y, Cb, Cr
DVI-I
RGB 1
Change Input Source
		Function Key
IconNameIcon Name
UpFreeze
DownBlank
LeftKeystone Correction +
RightKeystone Correction -
MenuIncrease Brightness
Auto SyncDecrease Brightness
MuteHigher Contrast 

49
Control Panel Window Introduction
	Function Key
IconName
Lower Contrast
Zoom In
Zoom Out
Volume Up
Volume Down
	
Projector Status
IconName
System Status
Input Source Status
Lamp Timer
Air Filter Timer   

50
Control Panel Window Introduction
	Network Control Window introduction
IconName
Description
Scan allCapture the all registered projectors’ information one 
time only.
Start Auto ScanAccording to the system setting, get the projector 
information automatically.
Stop Auto CaptureStop scanning the projector information.
Auto SearchSearch the projector in the same network to register 
and modify the setting.
Open Project FileOpen	project	file	which	was	saved.
Save Project FileSave the registered...

Maintenance Of Projector
51
Maintenance of Projector
Filter
Keep	the	air	filters	clean	by	cleaning	them	periodically.	
By using Filter Counter the projector can remind you of the timing.
There	are	2	types	of	air	filters	in	this	projector,	one	is	black	sponge	attached	just	back	side	of	the	filter	cover	and	the	other	is	the	filter	assembly	called	Anti-dust	filter(consists	
of a white folded cloth and black frame).
How to clean or replace the filters
Turn off the projector, and unplug the power cord. Wait...

52
Maintenance of Projector
6
4.	Install	the	Anti-dust	filter	to	the	filter	cover.
(a)		Place	the	Filter	cover	so	as	the	sponge	filter	faces	you.
(There is >PC< sign on the top middle of the Filter cover.)
(b)		 Place	the	 Anti-dust	filter	on	it	so	as	the	4	white	hooks	show	up	through	the	openings in the corners.
(There is >ABS< sign on the top of the black frame.)
(c)			 Slide	down	the	 Anti-dust	filter	so	that	the	two	black	hooks	of	the	 Anti-dust	filter	go	into the slots on the bottom of the Filter...

53
Maintenance of Projector
Lamp
Please turn off the projector and unplug the AC power cord. And then, let the projector 
cool down at least 60 minutes.
Replacing New Lamp(Part Number:23040021)
1. Remove the lamp door.
2.  Loosen 2 screws of the lamp holder. Hold the handle on the top of the lamp, pull out 
the lamp straight off the projector.
3.	Insert	new	lamp,	lock	the	lamp	door	firmly	with	2	screws.
4. Put the lamp door on.
5. Please reset the lamp timer after replacing lamp. (P.32)
When	changing...

54
Maintenance of Projector
 WARNING
The projector uses a high-pressure mercury lamp.
The	explosion	of	lamp	with	a	loud	bang	or	burn	out	could	possibly	cause	injury	or	a	fire.
When	the	bulb	bursts,	it	is	possible	for	shards	of	glass	to	fly	into	the	lamp	housing;	and	
for gas containing mercury to escape from the projector’s vent holes.
If the lamp has broken, do not check the inside of the projector. Please ventilate the room 
immediately.
Do not touch or bring your face close to the broken pieces since...

55
Maintenance of Projector
Additional
- In order to ensure the safe use of your projector, please contact your dealer to inspect 
about once a year.
- Before maintenance, make sure the power cable is unplugged, allow the pr\
ojector to 
cool	sufficiently.	 The	high	temperature	state	of	the	projector	could	cause	a	burn	in	and/
or malfunction to the projector.
-Never try to maintain the inside of the projector by yourself. 

Troubleshooting
56
Troubleshooting
Indicator
The power and lamp indicators show the status of the projector. Before requesting repair, 
check the projector status using the chart below. If the problem cannot be resolved, 
contact your dealer.
In normal status~~~
POWERLAMPCONDITIONSDESCRIPTION
Blinking In 
Green Off
Stand by mode Projector is ready to be turned 
on.
Lighting In 
Green Off
On mode Projector is on and operating.
Lighting In 
Green Blinking In 
Red 
( Slow ) Cool down mode Projector is in...

57
Troubleshooting
Error For Machine Defects
The following problems may be confused with a machine defect. Check and \
follow the 
table. If it couldn’t be improved, contact your dealer.
SymptomCause / Remedy
Projector power
does not turn onThe power cord is disconnected.
Plug the power cord into an AC outlet.
Intending to turn on the projector again during the cool down 
mode.
Wait until the cool down mode has completed.
There is no lamp and/or lamp cover is not firmly closed.
Please turn off the power...