Home > Eiki > Projector > Eiki Lc-Xip2600 Interactive Projector Owners Manual

Eiki Lc-Xip2600 Interactive Projector Owners Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Eiki Lc-Xip2600 Interactive Projector Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 422 Eiki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Control Panel Window Introduction
    48
    Control Panel Window Introduction
    		Power Control
    IconName
    Power on
    Power off
    		Input Source
    IconName
    Video
    S-Video
    Y, Pb, Pr / Y, Cb, Cr
    DVI-I
    RGB 1
    Change Input Source
    		Function Key
    IconNameIcon Name
    UpFreeze
    DownBlank
    LeftKeystone Correction +
    RightKeystone Correction -
    MenuIncrease Brightness
    Auto SyncDecrease Brightness
    MuteHigher Contrast 
    						
    							49
    Control Panel Window Introduction
    	Function Key
    IconName
    Lower Contrast
    Zoom In
    Zoom Out
    Volume Up
    Volume Down
    	
    Projector Status
    IconName
    System Status
    Input Source Status
    Lamp Timer
    Air Filter Timer   
    						
    							50
    Control Panel Window Introduction
    	Network Control Window introduction
    IconName
    Description
    Scan allCapture the all registered projectors’ information one 
    time only.
    Start Auto ScanAccording to the system setting, get the projector 
    information automatically.
    Stop Auto CaptureStop scanning the projector information.
    Auto SearchSearch the projector in the same network to register 
    and modify the setting.
    Open Project FileOpen	project	file	which	was	saved.
    Save Project FileSave the registered projector in this project.
    System SettingSetting the projector system reminder message.
    AboutIcon content description.
    ExitExit the Network software.
    Register projectorRegister projector’s information.
    ExitCancel registered information. 
    						
    							Maintenance Of Projector
    51
    Maintenance of Projector
    Filter
    Keep	the	air	filters	clean	by	cleaning	them	periodically.	
    By using Filter Counter the projector can remind you of the timing.
    There	are	2	types	of	air	filters	in	this	projector,	one	is	black	sponge	attached	just	back	side	of	the	filter	cover	and	the	other	is	the	filter	assembly	called	Anti-dust	filter(consists	
    of a white folded cloth and black frame).
    How to clean or replace the filters
    Turn off the projector, and unplug the power cord. Wait to allow the projector to cool down	sufficiently.	
    1.   Push up 2 white stoppers of the Filter cover and remove it from the side of projector as shown below. 
    2.		
    Remove	the	 Anti-	dust	filter	from	the	Filter	cover	by	pushing 	and	sliding	it	as	shown	below.	(There	is	>ABS<	sign	on	the	top	the	black	frame	of	the	 Anti-dust	filter.)
    3.  		
    Clean	the	filters	with	a	vacuum	cleaner	except	for	the	back	side	of	the	sponge,	
    because the vacuum cleaner may suck it. Brush the sponge gently by a bru\
    sh. 
    (Do	not	clean	the	filters	with	water.)
    *If	the	 Anti-dust	filter	is	too	dirty	to	clean,	please	replace	it	with	new	one.
    The	part	number	of	the	 Anti-dust	filter	is	"13340233".
    12
    3
    >ABS<
    Sponge	filter     
    						
    							52
    Maintenance of Projector
    6
    4.	Install	the	Anti-dust	filter	to	the	filter	cover.
    (a)		Place	the	Filter	cover	so	as	the	sponge	filter	faces	you.
    (There is >PC< sign on the top middle of the Filter cover.)
    (b)		 Place	the	 Anti-dust	filter	on	it	so	as	the	4	white	hooks	show	up	through	the	openings in the corners.
    (There is >ABS< sign on the top of the black frame.)
    (c)			 Slide	down	the	 Anti-dust	filter	so	that	the	two	black	hooks	of	the	 Anti-dust	filter	go	into the slots on the bottom of the Filter cover. 
    (you shall hear a "click" sound)
    Make sure that all of 4 white hooks of the Filter cover are well hooked \
    on the 
    frame.
    5.		 Insert	the	projected	parts	of	the	Filter	cover	to	the	side	of	the	projector	first	and	then	close the Filter cover by pushing 2 white stoppers. Make sure that the F\
    ilter cover is 
    well closed.
    6. Reset the Filter Timer.(P.34) 
    						
    							53
    Maintenance of Projector
    Lamp
    Please turn off the projector and unplug the AC power cord. And then, let the projector 
    cool down at least 60 minutes.
    Replacing New Lamp(Part Number:23040021)
    1. Remove the lamp door.
    2.  Loosen 2 screws of the lamp holder. Hold the handle on the top of the lamp, pull out 
    the lamp straight off the projector.
    3.	Insert	new	lamp,	lock	the	lamp	door	firmly	with	2	screws.
    4. Put the lamp door on.
    5. Please reset the lamp timer after replacing lamp. (P.32)
    When	changing	lamp,	it	is	recommended	that	you	change	the	filer	at	the	same	time. 
    						
    							54
    Maintenance of Projector
     WARNING
    The projector uses a high-pressure mercury lamp.
    The	explosion	of	lamp	with	a	loud	bang	or	burn	out	could	possibly	cause	injury	or	a	fire.
    When	the	bulb	bursts,	it	is	possible	for	shards	of	glass	to	fly	into	the	lamp	housing;	and	
    for gas containing mercury to escape from the projector’s vent holes.
    If the lamp has broken, do not check the inside of the projector. Please ventilate the room 
    immediately.
    Do not touch or bring your face close to the broken pieces since it migh\
    t get into your 
    eyes or mouth. In case of injury, seek medical advice immediately.
    Disposal of a Lamp
    Dispose of a lamp in accordance with the local recycling laws.
    Do not put it to your trash.
    Recycling Lamp’s laws of the USA, go to www.lamprecycle.org.
    Recycling Product’s laws of USA, go to www.eiae.org.
    Recycling Product’s laws of Canada, go to  www.epsc.ca.
    For more information about recycling laws, please contact local governme\
    nt agency or 
    dealer.
    CAUTION HOT
    Before replacing the Lamp unit, pay attention to the following items:
    1.The Lamp is optional part. Contact the dealer for replacement lamp.
    2.  The lamp becomes very hot when in use. Turn the power off and disconnect the power 
    cord.
    3.Wait for 1 Hour before replacing the lamp.
    4. Do not use old lamp unit. 
    						
    							55
    Maintenance of Projector
    Additional
    - In order to ensure the safe use of your projector, please contact your dealer to inspect 
    about once a year.
    - Before maintenance, make sure the power cable is unplugged, allow the pr\
    ojector to 
    cool	sufficiently.	 The	high	temperature	state	of	the	projector	could	cause	a	burn	in	and/
    or malfunction to the projector.
    -Never try to maintain the inside of the projector by yourself. 
    						
    							Troubleshooting
    56
    Troubleshooting
    Indicator
    The power and lamp indicators show the status of the projector. Before requesting repair, 
    check the projector status using the chart below. If the problem cannot be resolved, 
    contact your dealer.
    In normal status~~~
    POWERLAMPCONDITIONSDESCRIPTION
    Blinking In 
    Green Off
    Stand by mode Projector is ready to be turned 
    on.
    Lighting In 
    Green Off
    On mode Projector is on and operating.
    Lighting In 
    Green Blinking In 
    Red 
    ( Slow ) Cool down mode Projector is in cool down mode 
    and will not respond to user 
    input.
    Lighting In 
    Green Blinking In 
    Red 
    ( Fast ) Cool down mode When the projector is turned on 
    in 5 minutes after it was turned 
    off.
    In abnormal status~~~
    POWERLAMPCONDITIONS
    DESCRIPTION
    Blinking In 
    Green Blinking In 
    Red 
    ( Fast ) Fan fault mode The projector has detected a 
    problem of a slow internal fan 
    speed. The lamp will shut off 
    automatically. Contact your 
    dealer. 
    Blinking In 
    Green Lighting In 
    RedLamp cover open The lamp cover is open or there 
    is a problem with the lamp. If the 
    lamp door is closed and replacing 
    the lamp does not correct the 
    issue, contact your dealer.
    Blinking
    In Green (Fast) Blinking In 
    Red 
    ( Fast ) High temperature The projector has overheated and 
    shut itself down.
    Correct the over temperature 
    condition immediately.
    1.  
    Check that the ventilation slots 
    are free from obstructions.
    2.  Check the cleanliness of the 
    air	filter.
    Blinking In 
    Green (Slow) Blinking In 
    Red 
    (Slow) Lamp fail The lamp does not light. Come 
    back to "stand by mode", and 
    press the power button. 
    						
    							57
    Troubleshooting
    Error For Machine Defects
    The following problems may be confused with a machine defect. Check and \
    follow the 
    table. If it couldn’t be improved, contact your dealer.
    SymptomCause / Remedy
    Projector power
    does not turn onThe power cord is disconnected.
    Plug the power cord into an AC outlet.
    Intending to turn on the projector again during the cool down 
    mode.
    Wait until the cool down mode has completed.
    There is no lamp and/or lamp cover is not firmly closed.
    Please turn off the power and disconnect the power plug from the power 
    outlet.	Check	if	the	lamp	is	installed	or	the	lamp	cover	is	firmly	closed	
    and turn on the power again.
    Power cord has impaired.
    When you touch the power cord, the indicator goes on then off, please 
    remove the power cord and connect it again. If the situation is repeated\
    , 
    remove the power cord and contact your dealer.
    No Image The input is not connected correctly.
    Select the appropriate input source.
    No signal input.
    Connect correctly.
    The lens cover is attached to the lens.
    Remove the lens cover.
    Colors are pale Color density and color matching are not adjusted correctly.
    Adjust the RGB setting.
    Color lose.
    Caused by poor VGA cable connection.
    Abnormal brightness 
    & contrast Brightness and contrast are not adjusted correctly.
    Adjust the brightness and contrast setting.
    The lamp is near the end of its service life.
    Replace with a new lamp.
    Image is blurred The projection lens is not focused.
    Adjust the focus using the focus ring.
    The lens is dirty or misty.
    Clean the lens. 
    						
    All Eiki manuals Comments (0)

    Related Manuals for Eiki Lc-Xip2600 Interactive Projector Owners Manual