Eiki Lc-Xip2600 Interactive Projector Owners Manual

Before Use
38
Before Use
Before Using Network Control Software
		Copy and paste the "Network Control Software" folder in the CD-ROM of th\
e 
Owner's Manual to the PC.
		Create and put the short-cut icon for "Network Control.exe" on the deskt\
op.
				Confirm	that	 AC	is	supplied	to	the	projector	and	the	projector	and	the	PC	are	
connected to each other with LAN cable (through the network).
Activate Network Control Software
		Execute the Network Control Software.
		Monitor window...

39
Before Use 
Projector Auto Search.
		Click the  (Projector search), then the Search Window below appears.
		Click  (search again), then the target projectors will be listed as follows.
NOTE
If the security warning window appears, please select "Unblock" to allow\
 the 
Network Control software to work.

 

40
Before Use
		Click  (register projector), then the projectors will be shown in the Monitor 
Window as shown below.
 Monitor window
		After changing the projector setting, you can save the data by clicking \
 button or 
cancel by clicking  button.
ItemDescription
Projector nameShow the Host name. (16 characters at most in 
ASCII.)
IP Address Show the IP Address.
Mask Show the Subnet Mask.
Gateway Show the Gateway.
MAC Show up the MAC Address.
(The	default	value	can	not	be	modified.)
DHCP Capture IP...

41
Before Use 
Sorting the projectors 
		Projector can be sorted easily by clicking the monitor window title (Gr\
oup Name) or 
(Projector Name).
		After registering, you can click  button (Data single capture) in the tool bar or 
click  button (Start Auto Scan) to update the status.
NOTE

While Auto Scan is running to update the status, the scroll bar for the window\
 is grayed 
out and the hidden column can not be shown. Therefore before starting Auto Scan place 
the column in the window by using...

Registering And Configuring The Projector
42
Registering And Configuring The Projector
Delete
			Select the registered projector in monitor window. Click mouse right key and select 
"Delete" to erase the registered projector data.
< Graph 6 > : Register Table. 

43
Registering And Configuring The Projector
Projector Setting (Setting for individual projector)
		Select the registered projector in monitor window. Click mouse right key and select 
							"projector	setting"	to	modify	the	registered	projector	data.	 After	finishing	the	setting,	
you can save by clicking  button or cancel by clicking  button.
< Graph 7 > : Register table.
< Graph 8 > :Setting table. 

44
Registering And Configuring The Projector
System Setting (Setting for all projectors)
	Click  button (system setting) to modify system alert setting.
Saving the setting
 
< Graph 9 >
Note: 
Alert setting in System Setting vs Projector Setting
Whenever the "
" Save button is pressed in System Setting, the value becomes 
effective for all the projectors registered.
After this if the value in Projector Setting is changed and saved, the v\
alue becomes 
effective only for the projector. 

45
Registering And Configuring The Projector
System Setting
Monitor
ItemDescription
Lamp TimerRead lamp use time from projector.
Air Filter Alert Read Air Filter Timer from projector.
System Status/
Tempeture Level Read System Status and Temperature from projector in Power On 
status.
Input Source Read Input Source Selection from projector in Power ON status.
< Table 2 >
Default Setting
ItemDescription
Lamp Timer Alert (Hr.) Default Setting Includes 1000/1500/2000/3000 Hours.
When Lamp Timer reaches...

46
Registering And Configuring The Projector
Saving the Project File
Save	the	Configuration	above	as	Project	File	by	clicking	the	save	button	in	the	Tool	bar	
in the Monitor window before closing Network Control Software.
If	it	is	not	saved,	all	the	configuration	above	will	be	lost.
From	next	time	after	starting	this	Network	Control	Software	the	configuration	can	be	
recovered easily by opening the Project File. 

47
Registering And Configuring The Projector
Link(Controlling Projector)
		Select the registered projector in monitor window. Click mouse right key and select 
"Link" to show the control panel table and the projector connecting stat\
us.
< Graph 12 > : The control panel table