Eiki Lc-Xip2600 Interactive Projector Owners Manual

Safety Labels
8
Safety Labels
Safety labels are used on or within the projector to alert you to items \
or areas 
requiring your attention. 
WARNING LABEL
EMI Label
LAMP DOOR WARNING LABEL 

Part Names
9
Part Names
87
6
5
4
7
1
82
3
9
Projector
1 Control panel
Operating system.
        Lens Cover
Attach when not using to protect the lens 
from becoming dirty or damaged.
  Filter cover
Prevents dust and other foreign particles 
from being drawn into projector.
Remove	the	filter	cover	to	clean	the	air	
filter.
 Focus ring
Use the focus ring to focus the projector 
image.
Rotate the focus ring until the image is 
clear.
 Zoom ring
Use the zoom ring to adjust the size of the 
projected image....

10
Part Names
110 KEYSTONE
Adjust the vertical keystone. 
11 VOLUME + / -
Sound louder or lower.
112 INPUT
Select input source:
Note : 
If the projector can not be captured the 
signals within 15 minutes, it will be shut 
down automatically.
113 MENU
Display or hide the OSD main menu.
114 BLANK
Blank the projected image. The time of 
Blank mode can be set in 15 minutes, 30 
minutes or 60 minutes. The projector will 
shut down automatically after passing each 
set time.
Control Panel
10
1111
12
1413 15...

11
Part Names
Rear
A USB
Connect the USB cable to a computer
to utilize the Interactive functions.
B RS232
Serial data port for controlling the projector 
with  a  computer  or  other  RS-232  control 
device.
C AUDIO IN 1 & D AUDIO IN 2
Mini jack port corresponds to computer 
input.	(RGB	IN→AUDIO	IN	1,	DVI-1	IN	
→AUDIO	IN	2)
E AUDIO OUT 
T h i s   j a c k   o u t p u t s   t h e   a u d i o   s i g n a l 
from  computer  signal  to  external  audio 
equipment.
F RGB IN
Input analog RGB signal from a...

Setting Up
12
Setting Up
When installed against a wall, leave about 20cm (7.9in.) between the p\
rojector and the wall.
6.12~7.37
4.06~4.9
3.03~3.67
2.01~2.43
1.59~1.94
1.18~1.45
0.77~0.95Distance(M)
Image size(inch)
6.12~7.37
4.06~4.90
3.03~3.67
2.01~2.43
1.59~1.94
1.18~1.45
0.77~0.95
Image size(inch)
Distance(M)
Arrangement
1. 
Before installation, make sure that the projector is turned off and the power cord is disconnected.
2. Do not set up and move the projector, while it is hot.
3.   The distance...

13
Setting Up
Power ON / OFF
Turning On The Power
1.		Make	sure	that	power	cord	is	firmly	and	
correctly connected to the projector.
2. The green Power indicator blinks slowly.
3. Remove the lens cover. 
4.   Press POWER button on the control panel or 
the remote control to turn on the projector.
5.  Rotate the zoom ring to adjust the screen size.
6. Rotate the focus ring to adjust the focus.
Turning Off The Power
1.  Press the POWER button on the control 
panel or the remote control. The "power...

14
Setting Up
Setting Up The Projector
The projector supports the following four different projection methods. 
1. Front projection
2. Rear projection3. Rear ceiling projection
4. Front ceiling projection
Special installation is required in order to suspend the projector from \
the ceiling. Please ask your 
dealer for details. 
0˚
180˚
270˚ 90˚The projector can be installed pitched by any 
angle (360 degree) without any setting in fan 
mode. As for rolling it must be within 10 degree. 

15
Setting Up
Ceiling Mounted Installation Guide 
Attach	ceiling	mount	at	four-suspension	bracket	fixing	points	when	suspending	from	a	ceiling.	
Special installation is required in order to suspend the projector from \
the ceiling. Please ask your 
dealer for details.
Security Anchor
The product is equipped with security anchor and PIN 
LOCK (See page 33 for detials) functions to help prevent 
unauthorized removal of the projector.
MAX M4x8 mm For Mounting
WARNING
►Do	not	grasp	the	security	anchor	to...

16
Setting Up
Adjusting The Projector’s Elevation
Use the adjustable foot at the front of the projector to set the image h\
eight.
1   Holding the projector, push the foot adjust 
buttons to loosen the front adjustable foot.
12   Position the front side of the projector to the 
desired height.
3   Release the foot adjust buttons in order to 
lock the front adjustable feet.
14   Please make sure that the front adjustable 
feet are locked.
									 Please	rotate	the	adjustable	feet	when	fine	
adjustment...

17
Setting Up
Before starting, make sure that the projector and computer are both turn\
ed off.
Connect the computer 
Connect the computer cable from the computer to the projector's RGB IN o\
r DVI-I IN.
Connect a computer cable from the MONITOR OUT to an external monitor to view the
signal on RGB IN or DVI-I IN. Tighten the screw on all connectors.
How To Connect
Laptop or desktop computer
AUDIO OUTMOUSERS-232AUDIO OUTDVI OUTVGA OUTRGB IN
AUDIO IN 
VIDEO OUT AUDIO OUT (L)&(R)
S-VIDEO OUTYPb/Cb...