Dukane Imagepro 8806 Portable Lcd Projector Users Manual

							
9
2
2. Operating Environment
Operating Environment
2-2. Operating Environment
The following is the operating environment for Image Express Utility 2.0\
.  For the operating
environment of other software, please refer to the help function of each\
 software.
Windows 2000 Professional
Windows XP Home Edition
Windows XP Professional
Windows XP Tablet PC Edition
•Windows power-saving function is not supported.
• The Easy Connection only supports the Computer 
Administrator authority of Windows XP.
IBM PC/AT compatible personal computers
CD-ROM drive required for installation
Sender personal computer Pentium MMX processor or higher required
Pentium 800 MHz or higher recommended
Recipient personal computer Pentium III 800 MHz or higher required
Pentium III 1.2 GHz or higher recommended
Windows XP
128 MB or more required (192 MB or more recommended)
•  More memory may be necessary if other applications run 
at the same time.
Windows 2000 64 MB or more required (128 MB or more recommended)
•  More memory may be necessary if other applications run 
at the same time.
TCP/IP-compatible LAN or wireless LAN environment required
1024 dots  × 768 lines recommended
High Color (15 bits, 16 bits)
True Color (24 bits, 32 bits)
•  256 or fewer colors are not supported.
Supported OS
Supported hardware
CPU
Memory
Network environment
Resolution
Screen Colors
ReferenceIf the communication mode has been set to  “802.11 Ad  Hoc ” for wireless LAN of the
projector, IEEE802.11b specification (maximum transmission speed of 11 Mbps) is applied. 
						

							
10
3. Connecting LAN Cable
3. Connecting LAN Cable
Connect a LAN cable to the LAN port (RJ-45) of the projector when conn\
ecting the projector to
wired LAN.
After connecting LAN cable to the projector, set the required settings for the projector
(
page 24).
PC CARDCOMPONENT INUSB LANAUDIO INCOMPUTER 3 IN
COMPUTER 1 IN COMPUTER 2 INPC CONTROLMONITOR OUT
AUDIO OUTCb/Pb
L/MONO R
Y
Cr/Pr
AC IN
S-VIDEO IN VIDEO INAUDIO IN
LAN
Server
HUB, etc.LAN cable
(commercially available) 
						

							
11
4. Attaching Wireless LAN Card
Attaching Wireless LAN Card
4
4. Attaching Wireless LAN Card
Insert the wireless LAN card into the PC card slot on the rear panel of \
the projector.
Important
•The wireless LAN card must be inserted into the PC card slot in the corr\
ect direction.  It
cannot be inserted in the reverse direction.  If the card is inserted in\
 the reverse direction
with excessive force applied, the pins in the projector and the PC card \
slot may break.  Be
sure to insert the wireless LAN card with its label facing up.
• Before touching the LAN card, touch a metallic object (such as a door k\
nob or aluminum
window frame) to discharge the static electricity from your body.
Setting card in PC card slot
1Press POWER ON/STAND BY button to set the projector to Stand-by mode,
press the  “O (off) ” side of the main power switch of the projector.
2With the label on the wireless LAN card facing up, slowly insert the car\
d into
the slot horizontally.
P C C AR DCOMPONENT INUSB LA N
AUDIO IN COM
PUTER 3 IN
COM PUTER 1 IN COM
PUTER 2 IN
PC C ONTR OLMONITOR OUT
AUDIO OUT
C b/P
b
L/M
ONO R
Y
C
r/P
rS-VIDEO IN VIDEO INA
U DIO  I N
A C I N
PC CARDLAMPSTATUSPOWERO N/S TA N D B YSO URCE
A
U TO  A D JU ST
3 D  R EFO RM
Note
Do not apply any excessive force while inserting the card.
•   Always insert or remove the wireless LAN card when the main power is turned off. Failure to do so may cause projector   malfunction  or damage to wireless LAN card. If the projector will not work correctly, turn off the projector, wait 30 seconds,   and turn it back on. 
						

							
12
4. Attaching Wireless LAN Card
Removing card from PC card slot
1Press POWER ON/STAND BY button to set the projector to Stand-by mode,
press the  “O (off) ” side of the main power switch of the projector.
2Slowly press the PC card eject button.
The PC card eject button will slightly come forward.
3Slowly press the PC card eject button once again.
The inserted card will slightly come forward.
PC CARDCOMPONENT INUSB LAN
AUDIO IN COMPUTER 3 IN
COMPUTER 1 IN COMPUTER 2 IN
PC CONTROLMONITOR OUT
AUDIO OUT
C b/P
b
L/M
ONO R
Y
C
r/P
rS-VIDEO IN VIDEO INA
U DIO  IN
A C IN
PC CARDLAM PSTATUSPO WERON/S TA N D B YSO URCE
A
U TO  A D JU ST
3 D  R EFO RM
4Slowly pull out the card.
ReferencePC Card Lock
The supplied PC card lock prevents the wireless LAN card from being ejec\
ted use. Some
PC cards cannot be used based on their size and shape.
Use the supplled screw to fix the PC card lock.
PC C AR DCOMPONENT INUSB
Cb/P b
L/M ONO
Y
C
r/P rS-VIDEO IN VIDEO IN
AU
DIO  IN
PC C AR DCOMPONENT INUSB
Cb/P b
L/M ONO
R
Y C
r/P rS-VIDEO IN VIDEO IN
AU
DIO  IN
Wireless LAN card
PC card lock 
						

							
13
Setting the LAN Setting of Projector
5. Setting the LAN Setting of Projector
5
5. Setting the LAN Setting of Projector
ReferenceFor how to turn on/off the power to the projector and how to operate the buttons and
remote control of the projector, refer to “User ’s Manual ” included in the User ’s Manual
CD-ROM.
5-1. Displaying On-Screen Menu (LAN Mode)
Preparation: Turn on the power to the projector and project images to the screen.
It is not necessary to select the signals.
1Press the  button.
The on-screen menu will be displayed.
Highlight
2Use the  button to select the Setup submenu.
3Press the  button.
The  “Basic ” tab will be highlighted. 
						

							
14
5. Setting the LAN Setting of Projector
4Press the  button three times to highlight the “Installation ” tab.
5Press the SELECT    button three times to highlight  “LAN Mode ”, and press
the 
 button.
The  “LAN Mode ” screen will be displayed.
• To make setting of wireless LAN
Proceed to  “5-2. Wireless LAN ” (
next page).
• To make setting of wired LAN
Proceed to  “5-3. Wired LAN ” (
page 24). 
						

							
15
Setting the LAN Setting of Projector
5. Setting the LAN Setting of Projector
5
5-2. Wireless LAN
When inserting the wireless LAN card into the PC card slot of the projec\
tor, configure the LAN
settings in the “PC Card ” page of  “LAN Mode ” selected from On-Screen Menu.
 Flow of Setting
Setting of Network Type.
Select SSID in Site Survey.
Input SSID (if necessary).
Select Mode (if necessary).
Select Channel (if necessary).
Setting of WEP
Select the number of bits of WEP.
Select Key Select.
Set Key 1 to Key 4.
If Easy Connection is selected
8
8
9
10
11
12
13
14
15
16
16
1
3
Step      Display PC Card page of LAN Mode.
4Step      Input IP Address.
2Step      Select Profiles.
5Step      Input Subnet Mask.
6Step      Input Gateway.
7Step      Input DNS Configuration.
17Step      Finalize Advanced.
18Step      Reconnect the network.
19Step      Finalize the setting.
Step       -       Setting of Advanced.
Step      Enable or disable DHCP.
If Disabled (without check mark)
If Enabled (with check mark) 
						

							
16
5. Setting the LAN Setting of Projector
Setting Wireless LAN
1Display the  “PC Card ” page of  “LAN Mode ”.
Configure the setting of wireless LAN in the PC Card ” page of  “LAN Mode ” selected from On-Screen Menu.
 In the  “LAN Mode ” setting window, if the  “Built-in ” tab is highlighted, press the 
 button
to highlight  “PC Card ”.
The  “PC Card ” page will be displayed.
• If “LAN Mode ” is not displayed, refer to  “5-1. Displaying On-Screen Menu (LAN Mode) ” (page 13).
2Select  “Profiles ”.
 Press the SELECT    button once to highlight the  “Profiles ” field and press the  button.
 Use the 
SELECT  / button to highlight  “Profile 1 ”, and press the  button.
• “Profile 1 ” or  “Profile 2 ” can be stored in the memory of the projector as the setting for LAN.
• “Easy Connection ” is a mode in which the personal computer that runs Image Express Utilit\
y 2.0 in
the User Supportware 3 CD-ROM is easily connected to wireless LAN. Note that  “Easy Connection ” does not support software other than Image Express Utility 2.0.
• When  “Easy Connection ” is selected, the IP address and subnet mask do not have to be set.  To
use  “Easy Connection ”, the OS of the personal computer must be Windows XP ([Computer
Administrator] privilege).  It cannot be used with Windows 2000.
The communication mode is  “802.11 Ad Hoc ”. 
						

							
17
Setting the LAN Setting of Projector
5. Setting the LAN Setting of Projector
5
3Set “DHCP ”.
Check this check box if the network to which the projector is to be conn\
ected automatically assigns the
IP address via the DHCP server.
 Press the 
SELECT    button once to highlight  the  “DHCP ” check box and press the  button.
A check will be given if there is no mark found in the box.
• To clear the check box, press the 
 button once again.
• If “DHCP ” is checked, move the highlight to  “Advanced ” and press the 
 button. Proceed
to step 9 ( 
page 19). Input  “DNS Configuration ” field as necessary.
• If “DHCP ” is not checked, input  “IP Address ”,  “Subnet Mask ”,  “Gateway ”, and  “DNS
Configuration ” as necessary.  After each item has been set, move the highlight to  “Advanced ”
and press the 
 button.  Proceed to step 9 ( page 19).
4Input  “IP Address ”.
If  “DHCP ” is not checked, input the IP address assigned to the projector by the a\
dministrator of the
network to which the projector is connected.
 Press the 
SELECT    button once to highlight  the  “IP Address ” field and press the 
button.
The software keyboard will be displayed.
 Use the SELECT    button to select a number to input, and press the  button.
The characters will be input.
 Repeat step  above to input the IP address. •Each button on the software keyboard has the following function.
•“SP ”.................. Inputs space.
• “BS ”.................. Deletes one character to the left of the character insertion position in\
 the
“IP Address ” field.
• “
”“”........... Moves the character insertion position in the  “IP Address ” field to the left
or the right.
• [OK] .................. Finalizes the input character and closes the software keyboard.
• [Cancel] ............ Cancels the input character and closes the software keyboard. 
						

							
18
5. Setting the LAN Setting of Projector
5Input “Subnet Mask ”.
If  “DHCP ” is not checked, input the subnet mask of the network to which the proje\
ctor is connected.
The method of inputting is the same as that of the  “IP Address ” field.
6Input  “Gateway ”.
If  “DHCP ” is not checked, input the default gateway of the network to which the p\
rojector is connected.
The method of inputting is the same as that of the  “IP Address ” field.
7Input  “DNS Configuration ”.
Set the IP address of the DNS server of the network to which the project\
or is connected.
The method of inputting is the same as that of the  “IP Address ” field.
Example of setting 1
8Select  “Advanced ”.
Set  “Network Type ” and  “WEP ” (encryption) specific to wireless LAN.
 Use the 
SELECT  / button to highlight  “Advanced ” on the  “Profile ” page and press the 
button.
The  “Advanced ” screen will be displayed.