Dukane Imagepro 8806 Portable Lcd Projector Users Manual

							
111
7. Maintenance
2. Loosen the two screws securing the lamp housing until the phillips screw\
driver goes into a freewheelingcondition. The two screws are not removable.
Remove the lamp housing by holding it.
NOTE: There is an interlock on this case to prevent the risk of electrical shock. \
Do not attempt to circumvent this interlock.
3. Insert a new lamp housing until the lamp housing is plugged into the soc\
ket.
CAUTION
Do not use a lamp other than the replacement lamp 456-8806 .
Order this from your NEC dealer.
Secure it in place with the two screws.
Be sure to tighten the screws.
Interlock 
						

							
112
7. Maintenance
5. Connect the supplied power cable, turn on the Main Power switch and turn\
 on the projector.6. Finally, select the menu 
→ [Reset] → [Clear Lamp Hours] to reset the lamp life remaining and lamp usage
hours.
NOTE: When the lamp exceeds 2100 hours (up to 3100 hours in Eco mode) \
of service, the projector cannot turn on and the menu is not displayed.If this happens, press the HELP button on the remote control for 10 seco\
nds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
4. Reattach the lamp cover.
Slip the lamp cover back until it snaps into place.
PC 
C AR DL
A M PS
TA T
U SPO W ERO
N/STAN D BYEPC 
C AR D
L A M P
S TA T
U S
P O W E
RO N/STAN D BYE
1
2
P
C C A
R DLA M PSTA TU SPO W ERO N/S
TA
N D B YC
EPC C A
R D
L A
M P
S TA TU S
P O W ERO N/S
TA
N D B YC
E 
						

							
113
8. Using Optional Lenses
Five optional lenses are available for the NP2000/NP1000. See the inform\
ation described on this page to buy the
appropriate lens for your screen size and throw distance. See page 
11 5 for installing the lens.
 Table of Throw Distances and Screen Sizes for Optional Lenses
STANDARD (H X 1.5) - (H X 2.0)
NP01FL (H X 0.8)
NP03ZL (H X 1.9) - (H X 3.1) NP04ZL (H X 3.0) - (H X 4.8)
NP05ZL (H X 4.6) - (H X 7.0)
NP02ZL (H X 1.2) - (H X 1.5) 
Example: Distance from a 100 screen with the lens NP03ZL
Referring to the diagram on page 
124, H is 2.0 m/78.7. Therefore, the projection distances of 100 inches are from
2.0 m/78.7  × 1.9 to 2.0 m/78.7  × 3.1 = from 3.8 m/150 to 6.2 m/244.
NOTE: Distances may vary +/-5%
For screen sizes between 30 and 500 not indicated on the above table, \
use formulas below.
Throw distance for Standard lens (m/inch)=H  × 1.5 through H  × 2.0 Distance from 0.89m to 20.83m/35.1 to 820.2
Throw distance for NP01FL(m/inch)=H  × 0.8 Distance from 0.64m to 2.5m/25.3 to 98.6
Throw distance for NP02ZL(m/inch)=H  × 1.2 through H  × 1.5 Distance from 0.7m to 16.1m/27.5 to 634
Throw distance for NP03ZL(m/inch)=H  × 1.9 through H  × 3.1 Distance from 1.56m to 32.15m/61.4 to 1265.6
Throw distance for NP04ZL(m/inch)=H  × 3.0 through H  × 4.8 Distance from 3.6m to 49.52m/141.7 to 1949.5
Throw distance for NP05ZL(m/inch)=H  × 4.6 through H  × 7.0 Distance from 7.65m to 74.36m/301.3 to 2927.5
H= Screen width
Screen 
Size STANDARD
1.5  − 2.0
(m) (inches)NP02ZL
1.2  − 1.5
(m) (inches)NP03ZL
1.9  − 3.1
(m) (inches)NP04ZL
3.0  − 4.8
(m) (inches)NP05ZL
4.6  − 7.0
(m) (inches)NP01FL 0.8
(m)
(inches)30
40
60
67
72
80
84
90
100
120
150
180
200
210
240
250
270
300
400
500 0.89 – 1.20
1.20 – 1.62
1.83 – 2.45
2.05 – 2.75
2.21 – 2.96
2.46 – 3.29
2.59 – 3.46
2.78 – 3.71
3.09 – 4.13
3.72 – 4.96
4.66 – 6.21
5.60 – 7.47
6.23 – 8.30
6.54 – 8.72
7.49 – 9.97
7.80 – 10.39
8.43 – 11.23
9.37 – 12.48
12.51 – 16.66
15.65 – 20.83 0.70 – 0.92
0.95 – 1.25
1.44 – 1.89
1.62 – 2.12
1.74 – 2.28
1.94 – 2.54
2.04 – 2.67
2.19 – 2.86
2.44 – 3.18
2.93 – 3.83
3.68 – 4.80
4.42 – 5.77
4.92 – 6.41
5.17 – 6.74
5.91 – 7.71
6.16 – 8.03
6.66 – 8.67
7.41 – 9.64
9.89 – 12.87
12.37 – 16.10 27.5 –  36.4
37.3 – 49.1
56.9 – 74.5
63.7 – 83.4
68.6 – 89.8
76.4 – 99.9
80.3 – 105.0
86.2 – 112.6
96.0 – 125.4
115.5 – 150.8
144.9 – 188.9
174.2 – 227.1
193.8 – 252.5
203.5 – 265.2
232.9 – 303.4
242.7 – 316.1
262.2 – 341.5
291.5 – 379.7
389.3 – 506.8
487.1 – 634.0 1.56 – 2.51
2.37 – 3.79
2.66 – 4.25
2.86 – 4.57
3.19 – 5.08
3.35 – 5.34
3.60 – 5.73
4.01 – 6.37
4.82 – 7.66
6.05 – 9.59
7.27 – 11.53
8.08 – 12.81
8.49 – 13.46
9.72 – 15.39
10.12 – 16.04
10.94 – 17.33
12.16 – 19.26
16.24 – 25.70
20.32 – 32.15 61.4 – 98.6
93.5 – 149.4
104.7 – 167.1 112.8 – 179.8
125.6 – 200.1
132.0 – 210.3
141.7 – 225.5
157.7 – 250.8
189.8 – 301.6
238.0 – 377.7
286.2 – 453.8
318.3 – 504.5
334.3 – 529.9
382.5 – 606.0
398.6 – 631.4
430.7 – 682.1
478.8 – 758.2
639.4 –1011.9
799.9 –1265.6 3.60 – 5.83
4.03 – 6.53
4.34 – 7.03
4.84 – 7.82
5.09 – 8.22
5.46 – 8.81
6.08 – 9.81
7.32 – 11.79
9.18 – 14.77
11.05 – 17.75
12.29 – 19.73
12.91 – 20.73
14.77 – 23.70
15.39 – 24.70
16.63 – 26.68
18.49 – 29.66
24.70 – 39.59
30.90 – 49.52 141.7 – 229.7
158.8 – 257.0
171.1 – 276.6
190.6 – 307.9
200.4 – 323.5
215.0 – 346.9
239.5 – 386.0
288.3 – 464.2
361.6 – 581.5
434.9 – 698.7
483.8 – 776.9
508.2 – 816.0
581.5 – 933.3
605.9 – 972.4
654.8 –1050.5
728.1 –1167.8
972.4 –1558.7
1216.7–1949.5 7.65 – 11.73
8.05 – 12.33
8.63 – 13.23
9.62 – 14.72
11.58 – 17.70
14.52 – 22.17
17.46 – 26.65
19.43 – 29.63
20.41 – 31.12
23.35 – 35.59
24.33 – 37.08
26.29 – 40.06
29.23 – 44.54
39.04 – 59.45
48.85 – 74.36 301.3 – 462.0
316.8 – 485.5
340.0 – 520.7
378.6 – 579.4
455.8 – 696.8
571.7 – 872.9
687.5 –1049.0
764.8 –1166.4
803.4 –1225.1
919.3 –1401.2
957.9 –1459.9
1035.1–1577.3
1151.0 –1753.5
1537.2–2340.5
1923.4–2927.5
0.64
0.98
1.10
1.18
1.32
1.39
1.49
1.66
2.00
2.50
25.3
38.6
43.3
46.6
51.9
54.6
58.6
65.3
78.6
98.6
35.1 – 47.3
47.4 – 63.8
72.2 – 96.6
80.8 – 108.2
87.0 – 116.4
96.9 – 129.5
101.8 – 136.1
109.3 – 146.0
121.6 – 162.4
146.3 – 195.3
183.4 – 244.6
220.5 – 294.0
245.3 – 326.9
257.6 – 343.3
294.7 – 392.6
307.1 – 409.1
331.8 – 442.0
368.9 – 491.3
492.5 – 655.8
616.2 – 820.2 
						

							
114
8. Using Optional Lenses
 Lens Shift Adjustable Range
The top right diagram shows the location of the image position in the le\
ns. The lens can be shifted within the shaded
area as shown using the normal projection position as a starting point.
The projector has a lens shift feature that allows you to move the image\
 vertically or horizontally.
Desktop front projection
Ceiling front projection Vertical shift
Vertical shift
Max. 0.5V
Max. 
0.5V 1V 0.5V
0.1H 0.1H
1H
Width of projected image
Nomal projection position
Shift to left Shift to right
1V
Height of projected image 
						

							
115
 Replacing with Optional Lens
CAUTION
• Do not give a shock or excessive load to the projector or the lens compo\
nents as the projector and lens compo-
nents contain precision parts.
• When shipping the projector with the optional lens, remove the optional \
lens before shipping the projector. The lens and the lens shift mechanism may encounter damage caused by imprope\
r handling during transportation.
• Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans stop, and turn off the main power switch.
• Do not touch the lens surface when removing or installing the lens.
• Keep fingerprints, dust or oil off the lens surface. Do not scratch the lens surface.
• Work on a level surface with a soft cloth under it to avoid scratching.
• If you remove and store the lens, attach the lens cap to the projector t\
o keep off dust and dirt.
8. Using Optional Lenses
S ELEC TSELEC T
LE FT R
IG HT
DO W NU
P
PC C AR DLA M PSTA TU SPO W ERSOURCEAUTO ADJUST3D REFORMON/STAND BY
S
ELEC T
PC C AR D
L A M P
S TA TU S
P O W ERSOURCE
AUTO ADJUST
3D REFORM
ON/STAND BY
SELEC T
L E FT R
IG HT
D
O W NUP
2. Pull out the existing lens slowly.
Install the new lens
1. Insert the lens with the yellow protrusion on top.
SELEC TSELEC T
L
EFT R
IG HT
DO WNUP2. Rotate the lens clockwise.
Rotate the lens until you feel it click into place.
SELECT
LE FT R
IG HT
Remove the existing lens from the projector.
1. Rotate the lens counterclockwise while strongly pushing the
LENS RELEASE button all the way in.
The existing lens will be disengaged.
NOTE: If the lens cannot be removed even by using the LENS RELEASE but-ton, the anti-theft screw for lens may be used to secure the lens.
If such is the case, remove the anti-theft screw first. (→ page 116)
Yellow
Protrusion
LENS RELEASE
Button 
						

							
116
8. Using Optional Lenses
Using the anti-theft screw to prevent theft of the lensTighten the supplied anti-theft screw on the front bottom.
Hole of anti-theft screw for lens unit 
						

							
117
9. Appendix
 Troubleshooting
This section helps you resolve problems you may encounter while setting \
up or using the projector.
Indicator Messages
Power Indicator
Lamp Indicator
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady light Normal
Lamp has reached its end of life. Lamp
replacement message will be displayed.
Lamp has been used beyond its limit. The
projector will not turn on until the lamp is
replaced.
Lamp is in Eco mode
Red
Red
Green –
Replace the lamp.
(
→  page 
110)
Replace the lamp.
( →  page 
110)
–
Indicator Condition Projector Condition Note
Off
Blinking light
Steady light Green
Orange
Green
Orange 0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
The main power is off
The projector is getting ready to turn on.
Off Timer or Program Timer (Off Time) is
activated.
The projector is cooling down.
Program Timer (On Time) is activated.
The projector is turned on.
The projector is in Standby. –
Wait for a moment.
–
Wait for a moment.
–
–
–
Status Indicator
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady light Red
Green
Orange
Orange
Green 1 cycle (0.5 sec On,
2.5 sec Off)
2 cycle (0.5 sec On, 0.5 sec Of)
3 cycle (0.5 sec On,
0.5 sec Off)
4 cycle (0.5 sec On, 0.5 sec Off)
6 cycle (0.5 sec On, 0.5 sec Off)
1 cycle (0.5 sec On, 2.5 sec Off)
Reattach the lamp cover correctly.
(→  page 
112)
The projector is overheated. Move
the projector to a cooler location.
Power unit will not work correctly.
Fans will not work correctly.
Lamp fails to light. Wait a full
minute and then turn on again.
The projector is re-firing.
Both the built-in LAN and the wire-
less LAN cannot be connected to
the same network at the same time.
To use both built-in LAN and wire-
less LAN at the same time, connect
them to different networks.
( →  page 
90, 91)
You have pressed cabinet button
when Control Panel Lock is on.
( →  page 
82)
–
–
Lamp cover error
Temperature error
Power error
Fan error
Lamp error
Re-firing the lamp
Network conflict
Control Panel Lock is on
The projector is in Standby. Normal 
						

							
118
9. Appendix
Common Problems & Solutions (→  Power/Status/Lamp Indicator on page 11 7)
Does not turn on
Will turn off
No picture
Color tone or hue is
unusual
Image isn’t square to
the screen
Picture is blurred
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or
blinking
Vertical stripes in RGB
mode
USB mouse does not
work • Check that the power cable is plugged in and that the power button on th\
e projector cabinet or the remote
control is on. ( → page 
23, 24)
• Ensure that the lamp cover is installed correctly. ( → page 112)
• Check to see if the projector has overheated. If there is insufficient v\
entilation around the projector or if the room where you are presenting is particularly warm, move the projector t\
o a cooler location.
• Check to see if the lamp usage exceeds 2100 hours (up to 3100 hours : E\
co mode). If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. ( → page 
107)
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• Ensure that the Power Management, Off Timer or Program Timer is off. ( → page 
97, 99)
• Check to see if the lamp usage exceeds 2100 hours (up to 3100 hours : E\
co mode). If so, replace the lamp. After replacing the lamp, reset the lamp hours used. ( → page 
107)
• Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO\
, the COMPUTER 1, the COM- PUTER 2, the COMPUTER 3, the COMPONENT, the VIEWER or the LAN button on the remote control to select
your source. ( → page 
26)
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. ( → page 
74)
• Check to see if the image is muted. ( → page 36)
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the Reset in the Menu. ( → page 
107)
• Enter your registered keyword if the Security function is enabled. ( → page 45)
• Be sure to connect the projector and notebook PC while the projector is \
in standby mode and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on un\
less connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the \
result of the computers screen-
saver or power management software.
• See also the next page.
• Check if an appropriate color is selected in [Wall Color]. If not, select an appropriate option. ( → page 
81)
• Adjust [Hue] in [Adjust]. ( → page 74)
• Reposition the projector to improve its angle to the screen. ( → page 
27)
• Use the 3DReform function to correct the trapezoid distortion. ( → page 31)
• Adjust the focus. ( → page 
29)
• Reposition the projector to improve its angle to the screen. ( → page 27)
• Ensure that the distance between the projector and screen is within the \
adjustment range of the lens. ( → page
123, 124)
• Condensation may form on the lens if the projector is cold, brought into\
 a warm place and is then turned on. Should this happen, let the projector stand until there is no condensati\
on on the lens.
• Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO\
, the COMPUTER 1, the COM- PUTER 2, the COMPUTER 3, the COMPONENT, the VIEWER or the LAN button on the remote control to select
your source (Video, S-Video, Computer, Component, Viewer or LAN). ( → page 
26)
• Adjust the computer image manually with the [Clock]/[Phase] in [Adjust] \
 → [Image Options]. ( → page 75)
• Install new batteries. ( → page 
10)
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. ( → page 
10)
• Check if one or more remote sensors are enabled. Select [Setup]  → [Installation]  → [Remote Sensor] from
the menu. See page 
96.
• If the remote control cable plug is inserted into the REMOTE mini jack, \
the remote control does not function wirelessly. See page 
11.
• See the POWER/STATUS/LAMP Indicator. ( → page 
117)
• Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. b\
utton on the remote control. ( →
page 
33)
• Adjust the computer image manually with the [Clock]/[Phase] in [Adjust] \
 → [Image Options]. ( → page 75)
• Make sure that your USB mouse is properly connected to the projector. ( → page 
38)
The projector may not support some brands of a USB mouse.
Problem Check  These Items
For more information contact your dealer. 
						

							
119
9. Appendix
If there is no picture, or the picture is not displayed correctly.
• Power on process for the projector and the PC. Be sure to connect the projector and notebook PC while the projector is \
in standby mode and before turning on the
power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on un\
less connected to the projector before
being powered up.
NOTE: You can check the horizontal frequency of the current signal in the proje\
ctor’s menu under Information.  If it reads “0kH z”,
this means there is no signal being output from the computer. See page 104 or go to next step.
• Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will e\
nable/disable the external display.  Usu-
ally, the combination of the ‘Fn” key along with one of the 12 functio\
n keys gets the external display to come on or
off.  For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8\
 key combinations to toggle through
external display selections.
• Non-standard signal output from the computer If the output signal from a notebook PC is not an industry standard, the\
 projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use. Each
notebook PC has a different way of deactivate/reactivate the local LCD screens as described i\
n the previous step.
Refer to your computer’s documentation for detailed information.
• Image displayed is incorrect when using a Macintosh When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projector\
)
according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh a\
nd the projector, changing the DIP
switch on a Mac adapter may bounce an image slightly or may display noth\
ing. Should this happen, set the DIP
switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a displayable
mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for\
 a PowerBook which does not have a mini D-Sub
15-pin connector.
• Mirroring on a PowerBook* When using the projector with a Macintosh PowerBook, output may not be s\
et to 1024 x 768 unless “mirroring” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
• Folders or icons are hidden on the Macintosh screen Folders or icons may not be seen on the screen. Should this happen, sele\
ct [View]  → [Arrange] from the Apple
menu and arrange icons. 
						

							
120
9. Appendix
 Specifications
This section provides technical information about the projectors perfor\
mance.
Model Number                           8806
Optical
LCD Panel 0.8 p-Si TFT active-matrix with (Aspect ratio 4:3)
Resolution 1024   768 pixels* up to UXGA with Advanced AccuBlend (up to 1400  
1050 @ 60 Hz on DVI-D)
Standard Lens Manual zoom and focus: F1.7 - 2.2    f=24.4 - 32.6 mm
Lamp                                          8806 : 280 WAC (252 W in Eco mode)
NP1000 : 280 W AC (252 W in Eco mode)
Light Output                               8806 : 3500 lumens (approx.85% in Eco) NP1000 : 3500 lumens (approx.85% in Eco)
Contrast Ratio(full white: full black) 800:1
Image Size (Standard lens) 30 - 500 (0.76 m - 12.7 m) diagonal
Lens Options Fixed lens : NP01FL (throw ratio 0.8:1)
Zoom lens : NP02ZL (throw ratio 1.2-1.5:1)NP03ZL (throw ratio 1.9-3.1:1)
NP04ZL (throw ratio 3.0-4.8:1)
NP05ZL (throw ratio 4.6-7.0:1)
Lens Shift : Vertical +/- 0.5V, Horizontal +/- 0.1H
Electrical
Inputs 1 Analog RGB (Mini D-Sub 15 P), 1 Analog RGB R/cr, G/Y, B/cb, H, V (BNC  5), 1 Digital RGB (DVI-D 24 P), 1 Component Y, Cb/Pb, Cr/Pr
(RCA   3), 1 Component (Mini D-Sub 15 P) shared with COMPUTER 1
IN, 1 S-Video (Mini DIN 4P), 1 Video, 1 PC Card, 3 Stereo Mini Audio, 2
(L/R) RCA Audio, 1 Remote  Control (Stereo Mini)
Outputs 1 RGB (Mini D-Sub 15P), 1 Stereo Mini Audio
Slot 1 PC Card slot (PCMCIA Type II)
PC Control 1 PC Control Port (D-Sub 9P)
USB Port 1 A Type
LAN Port RJ-45
Video Compatibility NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM, HDTV: 1080i, 1080i/50Hz, 720p, 576p, 576i, 480p, 480i/60Hz
Scan Rate Horizontal: 15 kHz to 108 kHz (RGB: 24 kHz or over) Vertical: 48 Hz to 120 Hz
Video Bandwidth RGB: 100 MHz (-3dB)
Color Reproduction 16.7 million colors simultaneously, Full color
Horizontal Resolution NTSC / NTSC4.43 / PAL / PAL-M / PAL-N / PAL60: 540 TV lines SECAM: 300 TV lines
RGB: 1024 dots (H)  768 dots (V)
External Control RS232, IR, LAN, USB
Sync Compatibility Separate Sync / Composite Sync / Sync on G
Built-in Speakers 5W   2
Power Requirement 100 - 240V AC, 50/60Hz
Input Current 4.6A
Power Consumption 435W in Lamp Normal mode 365W in Lamp Eco mode
16W in Standby
* Effective pixels are more than 99.99%.