Digitus Router DN 7049 1 User Manual

							32 
for detailed descriptions. 
 
When you finish with all settings, please click ‘OK (7); if you want to go 
back to previous menu, click ‘Back’. 
 
 
2-3-6 Setup procedure for ‘Telstra Big P o n d’: 
 
 
 
This setting only works when you’re using Telstra big pond’s network 
service in Australia. You need to input: 
User Name (1):   Please input the user name assigned by Telstra. 
 
Password (2):   Please input the password assigned by Telstra. 
 
User decide login    Check this box to choose login 
server manually (3): server by yourself. 
 
Login Server(4):Please input the IP address of login server here. 
 
When you finish with all settings, click ‘OK (5); if you want to go back to 
previous menu, click ‘Back’. 
 
When all settings are finished, you’ll see the following message displayed 
on your web browser: 
 
1 
2 3 
4 
5  
						

							33 
 
 
Please click ‘Apply’ button to prepare to restart the router, and you’ll see 
this message: 
 
 
 
Please wait for about 30 seconds, then click ‘OK!’ button. Y ou’ll be back 
to router management interface again, and the router is ready with new 
settings.  
						

							34 
2-4 Basic Setup 
 
In this chapter, you’ll know how to change the time zone, password, and 
remote management settings. Please start your web browser and log onto 
router web management interface, then click ‘General Setup’ button on 
the left, or click ‘General Setup’ link at the upper-right corner of web 
management interface. 
 
  
 
 
2-4-1 Time zone and time auto-synchronization 
 
Please follow the following instructions to set time zone and time 
auto-synchronization parameters: 
 
Please click ‘S y s t e m’ menu on the left of web management interface, then 
click ‘Time Zone’, and the following message will be displayed on your 
web browser: Please select time zone at ‘Set time zone’ drop-down list, 
and input the IP address or host name of time server. If you want to 
HERE!  
						

							35 
enable daylight savings setting, please check ‘Enable Function’ box, and 
set the duration of daylight setting. When you finish, click ‘Apply’. 
Y o u’ll see the following message displayed on web browser: 
 
 
 
Press ‘Continue’ to save the settings made and back to web management 
interface; press ‘Apply’ to save the settings made and restart the router so 
the settings will take effect after it reboots. 
 
 
 
 
 
 
2-4-2 Change management password 
 
Default password of this router is 1234, and it’s displayed on the login 
prompt when accessed from web browser. There’s a security risk if you 
don’t change the default password, since everyone can see it. This is very 
important when you have wireless function enabled. 
 
To change password, please follow the following instructions: 
 
Please click ‘S y s t e m’ menu on the left of web management interface, then 
click ‘Password Settings’, and the following message will be displayed 
on your web browser: 
 
 
NOTE: You can refer to the instructions given in last chapter: ‘Using 
Quick Setup’, for detailed descriptions on time zone settings. 
1 
2 
3  
						

							36 
Here are descriptions of every setup items: 
C u r r e n t     Please input current password here. 
Password (1):  
 
New Password (2):  Please input new password here. 
 
Confirmed    Please input new password here again. 
Password (3):  
 
When you finish, click ‘Apply’. If you want to keep original password 
unchanged, click ‘Cancel’. 
 
If the password you typed in ‘New Password’ (2) and ‘Confirmed 
Password’ (3) field are not the same, you’ll see the following message: 
 
 
 
Please retype the new password again when you see above message. 
 
If you see the following message: 
 
 
 
It means the content in ‘Current Password’ field is wrong, please click 
‘OK’ to go back to previous menu, and try to input current password 
again.  
 
If the current and new passwords are correctly entered, after you click 
‘Apply’,   y o u’ll be prompted to input your new password: 
  
						

							37 
 
Please use new password to enter web management interface again, and 
you should be able to login with new password. 
 
 
2-4-3 Remote Management 
 
This router does not allow management access from Internet, to prevent 
possible security risks (especially when you defined a weak password, or 
didn’t change default password). However, you can still management this 
router from a specific IP address by enabling the ‘Remote Management’ 
Function. 
 
To do so, please follow the following instructions: 
 
Please click ‘S y s t e m’ menu on the left of web management interface, then 
click ‘Remote Management’, and the following message will be 
displayed on your web browser: 
 
 
 
 
1 2 3 
4  
						

							38 
Here are descriptions of every setup items: 
 
Host Address (1):  Input the IP address of the remote host you wish to 
initiate a management access.  
 
Port (2):  You can define the port number this router should 
expect an incoming request. If you’r e providing a 
web service (default port number is 80), you should 
try to use other port number. You can use the default 
port setting ‘8080’, or something like ‘32245’ or 
‘1429’. (Any integer between 1 and 65534) 
 
Enabled (3): Select the field to start the configuration. 
 
When you finish with all settings, click ‘Apply’, and you’ll see the 
following message displayed on web browser: 
 
 
 
Press ‘Continue’ to save the settings made and back to web management 
interface; press ‘Apply’ to save the settings made and restart the router so 
the settings will take effect after it reboots. 
  
						

							39 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: When you want to manage this router from another computer 
on internet, you have to input the IP address and port number of this 
router. I f   y o ur Internet service provider assigns you with a static IP 
address, it will not be a problem; but if the IP address your service 
provider assigns to you will vary every time you establish an internet 
connection, this will be a problem.  
 
Please either askasks your service provider to give you a static IP 
address, or use dynamic IP to host name mapping services like 
DDNS. Please refer to chapter 2-5-8 ‘DDNS client’ for details. 
NOTE: Default port number the web browser will use is ‘80’. If the 
‘Port’ setting in this page is not ‘80’, you have to assign the port 
number in the address bar of web browser manually. For example, if 
the IP address of this router is 1.2.3.4, and the port number you set is 
8888, you have to input following address in the address bar of web 
b r o w s e r : 
 
http://1.2.3.4:8888  
						

							40 
2-5 Setup Internet Connection (WAN Setup) 
 
Internet connections setup can be done by using ‘Quick Setup’ menu 
described in chapter 2-3. However, you can setup WAN connections up 
by using WAN configuration menu. You can also set advanced functions 
like DDNS (Dynamic DNS) here. 
 
To start configuration, please follow the following instructions: 
 
Please click ‘W A N’ menu on the left of web management interface, and 
the following message will be displayed on your web browser: 
 
Please select an Internet connection method depend on the type of 
connection you’re using. You can either click the connection method on 
the left (1) or right (2). If you select the connection method on the right, 
please click ‘More Configuration’ button after a method is selected. 
 
 
 
Dynamic IP   - Please go to section 2-5-1 
Static IP    - Please go to section 2-5-2 
PPPoE    - Please go to section 2-5-3 
PPTP    - Please go to section 2-5-4 
L 2 T P    - Please go to section 2-5-5 
Telstra Big Pond  - Please go to section 2-5-6 
DNS    - Please go to section 2-5-7 
DDNS    - Please go to section 2-5-8 
1 
2  
						

							41 
2-5-1 Setup procedure for ‘Dynamic IP’: 
 
 
 
Here are descriptions of every setup items: 
 
Host Name (1):  Please input host name of your computer, this is 
optional, and only required if your service provider 
asks you to do so.  
 
MAC Address (2):  Please input MAC address of your computer, if your 
service provider only permits computer with certain 
MAC address to access internet. If you’re using the 
computer which used to connect to Internet via 
cable modem, you can simply press ‘Clone Mac 
address’ button to fill the MAC address field with 
the MAC address of your computer,  
 
After you finish with all settings, please click ‘Apply’ (3); if you want to 
remove and value you entered, please click ‘Cancel’. 
 
After you click ‘Apply’, the following message will be displayed on your 
web browser: 
 
1 
2 
3