Digitus Router DN 7049 1 User Manual

							22 
2-3 Using ‘Quick Setup’ 
 
This router provides a ‘Quick Setup’ procedure, which will help you to 
complete all required settings you need to access the Internet in very short 
time. Please follow the following instructions to complete the ‘Quick 
Setup’: 
 
Please go to QuickSetup menu by clicking ‘QuickSetup’ button. 
 
 
 
 
 
 
 
 
 
HERE!  
						

							23 
And the following message will be displayed: 
 
1. Set Time Zone 
 
 
 
Here are descriptions of every setup items: 
 
Set Time    Please press  button, a drop-down list 
Zone (1):  will be shown, and you can choose a time zone of 
the location you live. 
 
Time Server   Input the IP address / host name of time server 
Address (2):   h e r e 
 
Daylight    If the country you live uses daylight saving, 
Savings( 3 ):  please check ‘Enable Function’ box, and choose the 
duration of daylight saving. 
 
After you finish with all settings, please click ‘Apply’ (4) button.  
 
 
 
 
 
 
 
 
 
 
 
 
 
1 
2 
3 
4 
NOTE: There are several time servers available on internet: 
 
129.6.15.28 (time-a.nist.gov) 
132.163.4.101 (time-a.timefreq.bldrdoc.gov) 
131.107.1.10 (time-nw.nist.gov) 
 
If you found that the time of router is incorrect, try another time server.  
						

							24 
2. Broadband Type 
 
 
Please choose the broadband (Internet connection) type you’re using in 
this page. There are s i x types of Internet connection, they are: 
 
Cable Modem   - Please go to section 2-3-1 
F i x e d-IP xDSL   - Please go to section 2-3-2 
PPPoE xDSL   - Please go to section 2-3-3 
PPTP xDSL    - Please go to section 2-3-4 
L2TP xDSL    - Please go to section 2-3-5 
Telstra Big Pond   - Please go to section 2-3-6 
 
I f   y o u’re not sure, please contact your Internet service provider. A wrong 
Internet connection type will cause connection problem, and you will not 
be able to connect to internet. 
 
If you want to go back to previous step, please press ‘Back’ button on the 
bottom of this page. 
 
 
 
 
 
NOTE: Some service providers use ‘DHCP’ (Dynamic Host 
Configuration Protocol) to assign IP address to you. In this case, you 
can choose ‘Cable Modem’ as Internet connection t y p e, even you’re 
using another connection type, like xDSL. Also, some cable modem 
uses PPPoE, so you can choose ‘PPPoE xDSL’ for such cable modem 
connection, even you’re using a cable modem.  
						

							25 
2-3-1 Setup procedure for ‘Cable Modem’: 
 
 
 
Here are descriptions of every setup items: 
 
Host Name (1):   Please input the host name of your computer, this is 
    optional, and only required if your s e r v i c e   p ro v i d e r 
      asks you to do so.  
 
MAC address (2):  Please input MAC address of your computer h e r e, if 
your service provider only permits computer with 
certain MAC address to access internet. If you’r e  
using the computer which used to connect to 
Internet via cable modem, you can simply press 
‘Clone Mac address’ button to fill the MAC address 
field with the MAC address of your computer. 
 
After you finish with all settings, please click ‘OK’ (3) button; if   y o u 
want to go back to previous menu, click ‘Back’.  
 
2-3-2 Setup procedure for ‘F i x e d-I P   x D S L’: 
 
 
1 
2 
3 
1 
2 
3 
4 
5  
						

							26 
Here are descriptions of every setup items: 
 
IP address    Please input IP address assigned 
assigned by your  by your service provider. 
Service Provider (1):  
 
Subnet Mask (2):  Please input subnet mask assigned by your service 
p ro v i d e r   
 
DNS address (3):  Please input the IP address of DNS server provided 
by your service provider. 
 
Service Provider  Please input the IP address of DNS server 
Gateway Address (4): provided by your service provider. 
 
 
 
 
 
When you finish with all settings, press ‘OK’ (5); if you want to go back 
to previous menu, click ‘Back’. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: You can choose this Internet connection method if your 
service provider assigns a fixed IP address (also know as static 
address) to you, and not using DHCP or PPPoE protocol. Please 
contact your service provider for further information. 
You must use the addresses provided by your Internet service 
provider, wrong setting value will cause connection problem.  
  
						

							27 
2-3-3 Setup procedure for ‘PPPoE xDSL’: 
 
 
 
Here are descriptions of every setup items: 
 
User Name (1):  Please input user name assigned by your Internet 
s e r v i c e   p ro v i d e r   h e re . 
 
Password (2):  Please input the password assigned by your Internet 
s e r v i c e   p ro v i d e r   h e re . 
 
Service Name (3):  Please give a name to this Internet service, this is 
optional 
 
MTU (4):  Please input the M T U  value of your network 
connection here. If you don’t know, you can use 
default value. 
 
Connection    Please select the connection type of Internet 
T y p e (5):  connection you wish to use (detailed explanation 
listed below). 
 
I d l e   Time Out ( 6 ):  Please input idle time out, (detailed explanation 
listed below). 
 
 
1 
2 
4 
3 
5 
6 
7  
						

							28 
When you finish with all settings, please click ‘OK’ (7); if you want to go 
back to previous menu, click ‘Back’. 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2-3-4 Setup procedure for ‘PPTP xDSL’: 
 
PPTP xDSL requires two kinds of setting: WAN interface setting (setup 
IP address) and PPTP setting (PPTP user name and password). Here we 
start from WAN interface setting: 
 
 
 
Select the type of how you obtain IP address from your service provider 
here. You can choose ‘Obtain an IP address automatically’ (equal to 
DHCP, please refer to ‘Cable Modem’ section above), or ‘Use the 
following IP address’ (i.e. static IP address) .   
MTU - Please use default value if you don’t know what it is, or ask 
your service provider for a proper value. 
 
Connection Type - There are 3 options: ‘Continuous’ - keep internet 
connection alive, do not disconnect, connect on Demand - only 
connects to Internet when there’s a connect attempt, and ‘Manual’ - 
only connects to Internet when ‘Connect’ button on this page is 
pressed, and disconnects when ‘Disconnect button is pressed. 
 
Idle Time Out: Specify the time to shutdown internet connect after no 
internet activity is detected by minute. This option is only available 
when connection type is ‘Connect on Demand’.  
						

							29 
WAN interface settings must be correctly set, or the Internet connection 
will fail even those settings of PPTP settings are correct. Please contact 
your Internet service provider if you don’t know what you should fill in 
these fields. 
 
Now please go to PPTP settings section: 
 
 
 
Here are descriptions of every setup items: 
User N a m e (1):  Please input user ID (user name) assigned by your 
I n t e r n e t   s e r v i c e   p ro v i d e r   h e re . 
 
Password (2):  Please input the password assigned by your Internet 
s e r v i c e   p ro v i d e r   h e re . 
 
PPTP  Please input the IP address of PPTP gateway 
Gateway (3):  assigned by your Internet service provider here. 
 
Connection    Please input the connection ID here, this is 
ID (4):     optional and you can leave it blank. 
 
MTU (5):  Please input the MTU value of your network 
connection here. If you don’t know, you can use 
default value. 
 
BEZEQ-ISRAEL (6): Setting item ‘BEZEQ-ISRAEL’ is only required to 
Check if you’re using the service provided by 
1 
2 
3 
4 
5 
6 
7 
9 
8  
						

							30 
BEZEQ network in Israel.  
 
Connection    Please select the connection type of Internet 
type (7):  connection you wish to use, please refer to last 
section for detailed descriptions. 
 
Idle Time    Please input the idle time out of Internet 
Out (8):  connection you wish to use, and refer to last section 
for detailed descriptions. 
 
When you finish with all settings, please click ‘O K   (9); if you want to go 
back to previous menu, click ‘Back’. 
 
 
2-3-5 Setup procedure for ‘L2TP   x D S L’: 
 
L2TP is another popular connection method for xDSL and other Internet 
connection types, and all required setting items are the same with PPTP 
connection. 
 
Like PPTP, there are two kinds of required setting, we’ll start from ‘WAN 
Interface Settings’: 
 
 
 
Please select the type of how you obtain IP address from your service 
provider here. You can choose ‘Obtain an IP address automatically’ (equal 
to DHCP, please refer to ‘Cable Modem’ section above), or ‘Use the 
following IP address’ (equal to static IP address, please refer to ‘PPPoE 
xDSL’ section above).   
						

							31 
WAN interface settings must be correctly set, or the Internet connection 
will fail even those settings of PPTP settings are correct. Please contact 
your Internet service provider if you don’t know what you should fill in 
these fields. 
 
Now please go to L2TP settings section: 
 
 
 
Here are descriptions of every setup items: 
 
User N a m e (1):   Please input user ID (user name) assigned by your 
     I n t e r n e t   s e r v i c e   p ro v i d e r   h e re . 
 
Password (2):  Please input the password assigned by your Internet 
s e r v i c e   p ro v i d e r   h e re . 
 
L2TP Gateway (3):  Please input the IP address of PPTP gateway 
assigned by your Internet service provider here. 
 
MTU (4):  Please input the MTU value of your network 
connection here. If you don’t know, you can use 
default value. 
 
Connection    Please select the connection type of Internet 
type (5):  connection you wish to use, please refer to last 
section for detailed descriptions. 
 
Idle Time    Please input the idle time out of I n t e r n e t 
Out (6):  connection you wish to use, and refer to last section 
1 
2 
4 
3 
5 
7 
6