Digitus Router DN 7049 1 User Manual

							12 
 
 
 
 
2-2-2Windows 2000 IP address setup: 
 
1. Click ‘S t a r t’ button (it should be located at lower-left corner of your 
computer), then click control panel. Double-click Network and Dial-up 
Connections icon; click Local Area Connection, and Local Area 
Connection Properties window will appear. Select ‘Internet Protocol 
(T C P / I P)’ and then click ‘Properties’  
  
						

							13 
 
 
2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS server 
address automatically’, then click ‘OK’. 
  
						

							14 
 
 
 
 
2-2-3Windows XP IP address setup: 
 
1. Click ‘S t a r t’ button (it should be located at lower-left corner of your 
computer), then click control panel. Double-click Network and Internet 
Connection s  icon, click Network Connections, then double-click Local 
A r e a   C o n n e c t i o n, Local Area Connection Status window will appear, 
and then click ‘Properties’ 
  
						

							15 
 
 
2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS server 
address automatically’, then click ‘OK’.  
						

							16 
 
 
 
2-2-4Windows Vista IP address setup: 
 
1. Click ‘S t a r t’ button (it should be located at lower-left corner of your 
computer), then click control panel. Click View Network Status and 
T a s k s, and then click Manage Network Connections. Right-click Local 
A r e a  N e t w o r k, then select ‘Properties’. Local Area Connection 
P r o p e r t i e s window will appear, select ‘Internet Protocol Version 4 (TCP / 
I P v 4 ) ,  and then click ‘Properties’ 
  
						

							17 
 
 
2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS server 
address automatically’, then click ‘OK’. 
  
						

							18 
  
						

							19 
2-2-5 Router IP address lookup  
 
After the IP address setup is complete, please click ‘start’ -> ‘run’ at the 
bottom-lower corner of your desktop: 
 
 
 
Input ‘c m d’, then click ‘OK’ 
 
  
						

							20 
Input ‘ipconfig’, then press ‘Enter’ key. Please check the IP address 
followed by ‘Default Gateway’ (In this example, the IP address of router 
is 192.168.2.1, please note that this value may be d i f f e r e n t.) 
 
 
 
 
 
 
 
3. Connect the router’s management interface by web browser 
 
After your computer obtained an I P  address from router, please start your 
web browser, and input the IP address of router in address bar. The 
following message should be shown: 
 
NOTE: If the IP address of Gateway is not displayed, or the address followed 
b y  ‘IP Address’ begins with ‘16 9’, please recheck network connection 
between your computer and router, and / or go to the beginning of this 
chapter, to recheck every step of network setup procedure.  
						

							21 
Please input user name and password in the field respectively, default 
user name is ‘admin’, and default password is ‘1234’, then press ‘OK’ 
button, and you can see the web management interface of this router: 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: If you can’t see the web management interface, and you’re 
being prompted to input user name and password again, it means you 
didn’t input username and password correctly. Please retype user 
name and password again. If you’re certain about the user name and 
password you type are correct, please go to ‘4-2 Troubleshooting’ to 
perform a factory reset, to set the password back to default value. 
 
TIP: This page shows the four major setting categories: QuickSetup, 
General Setup, Status, and Tools. You can find the shortcut which 
leads to thes e setting categories at the upper-right corner of every 
page, and you can jump to another category directly by clicking the 
link, and don’t have to go back to the first page.