Digital Projection Projector HIGHlite Laser 3D Series User Manual

page 63
Operating Guide
USING THE PROJECTOR
3D menu continued from previous page
Frame rate multiplication in 3D images
When displaying a low frame rate 3D video, the projector 
multiplies the frame rate to obtain a flicker-free image. For 
example, a 60Hz frame rate is doubled to 120 Hz, or a 48 Hz 
frame rate is tripled to 144 Hz.
Frame rate multiplication is an automatic process. It occurs in 
the background and cannot be modified by the user.
NotesL1R1L2
R2
L1
L1
R1R2
L2 L3
R2
R1
L3
L2IN
OUT
x2...

page 64
Operating Guide
USING THE PROJECTOR
Laser menu
• Power Mode
• Eco will automatically set the laser power to 30%.
• Normal will set the power to 100%.
• Set to Custom if you wish to adjust the power manually.
• Quiet reduces the noise level, running at up to 75% laser power.
• Custom Power Level
This setting is only available if Power Mode is set to Custom or Quiet.
Use the slider to set laser power:
• If Power Mode is set to Custom, choose a value between 1 and 28, 
ranging from 30% to 100% laser...

page 65
Operating Guide
USING THE PROJECTOR
Setup menu
• Orientation 
Choose from Desktop Front, Ceiling Front, Desktop Rear and 
Ceiling Rear.
• Auto Power Off 
Set this to On if you want the projector to go into STANDBY mode when no 
input source is detected for 20 minutes.
• Auto Power On
• Set this to On if you want the projector to start up immediately when the 
mains is connected.
• Set this to Off if you want the projector to go into STANDBY mode when 
the mains is connected. In this case, the...

page 66
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
Infrared Remote
• IR Enable
Set to Off if you wish to disable the remote control.
• IR Code
The projector and the remote control need a matching IR code: a two-digit 
number between 00 and 99.
The default IR code is 00. This is also a master code, which, if assigned to a 
remote, will work regardless of the value assigned to the projector.
To assign an IR code for the projector:
1. Select IR Code.
2. Use the LEFT  and...

page 67
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
Network
Set DHCP to On if the IP address is to be assigned by a DHCP server, or Off if it is 
to be set here.
• If DHCP is set to On, it will not be possible to edit IP Address, Subnet Mask, 
Gateway or DNS.
• If DHCP is set to Off:
1. Edit IP Address, Subnet Mask, Gateway and DNS as required.
2. Select Apply Settings and press ENTER.
Standby Power
If this setting is On, the LAN socket remains active when the projector is...

page 68
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
On Screen Display
• Position 
Select from the list where you want the OSD to appear on the screen.
• Transparency 
Choose between 0% (no transparency), 25%, 50% and 75%.
• Timeout 
The menus will disappear if no buttons are pressed within the selected l\
ength 
of time. If you want the menus to remain on screen permanently, then select 
Always On.
• Messaging 
If you do not want status messages to be displayed, set this...

page 69
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
Presets
The current image settings can be saved as a preset, which you can recal\
l later. 
The default settings can be recalled at any time as well.
Up to four custom presets can be stored for each input.
The following settings are saved in a preset:
• From the Image menu — Brightness, Contrast, Gamma, 
Adaptive Contrast, Saturation, Hue, Sharpness and Noise Reduction
• From the Color menu — Colorspace, Color...

page 70
Operating Guide
USING THE PROJECTOR
Information menu
This menu gives information about software and hardware configuration, input 
source and laser operating times It also allows you to restore the facto\
ry default 
settings.
Factor y Reset
To restore the factory default settings:
1. Navigate to Factory Reset and press ENTER/OK.
2. When prompted, use the LEFT  and RIGHT  arrow buttons to highlight the 
Ye s button and then press ENTER/OK to confirm your choice.
Notes
Reset Everything
YesNo...

REFERENCE GUIDE4 
Rev C Februar y 2015 
HIGHlite Laser 3D Series
High Brightness Digital Video Projector  

Reference Guide
IN THIS GUIDE
IN THIS GUIDE
The DMD™ ........................................................................\
...................................74
Choosing A Lens ........................................................................\
........................76
Basic calculation .......................................................................................................77
Basic calculation example...