Digital Projection Projector HIGHlite Laser 3D Series User Manual

page 13
Installation and Quick-Start Guide
CHANGING THE LENS
Changing The Lens
The lens hood
There are two types of lens hood, short and long. 
The short lens hood is used with the following lenses:
Throw ratiosPart number
0.77 : 1 fixed lens110-808
1.16 : 1 fixed lens110-809
1.45 - 1.74 : 1 zoom lens110-803
1.74 - 2.17 : 1 zoom lens112-878
2.17 - 2.90 : 1 zoom lens113-852
2.90 - 4.34 : 1 zoom lens110-806
The long lens hood must be used with the following long throw lens:
Throw ratiosPart number
4.34 -...

page 14
Installation and Quick-Start Guide
CHANGING THE LENS
Inserting a new lens
1. Insert the lens into the lens aperture, making sure that the plug on the\
 zoom drive 
mechanism lines up with socket on the right of the lens aperture.
2. Rotate the lens clockwise until it clicks into place.
3. Secure the lens hood to the front of the projector with the screws.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When...

page 15
Installation and Quick-Start Guide
CHANGING THE LENS
Removing the lens
1. Loosen the four screws securing the lens hood to the body of the project\
or. 
Remove the lens hood.
2. Push down the lens holder tab.
3. Rotate the lens anti-clockwise.
4. Pull the lens forward to remove it from the lens aperture.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may...

page 16
Installation and Quick-Start Guide
CHANGING THE FILTERS
Changing The Filters
1. Loosen the screws holding the filter cover.
2. Remove the old filter.
3. Insert the new filter. Make sure the air flow arrow on the side of the 
filter panel points toward the projector, as shown in the illustration.
4. Replace the filter cover and tighten the screws
Notes
	 Before	changing	the	filters,	always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
	When	changing	the...

page 17
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
Wait until the self-test has completed and the STANDBY indicator on the projector control panel shows blue. The system will be off and 
the projector will be in STANDBY mode.
2. Press ON on the remote control or STBY on the control panel to switch the projector ON....

page 18
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Selecting an input signal or test pattern
Input signal
• Connect an image source to the projector. The signal should be automatically detected by the projector, and should be displayed within 
two or three seconds.
• If more than one signal is connected, then select the input you want to \
display:
• Press one of the input buttons on the remote control.
• Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input...

page 19
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or using the lens buttons on the 
remote control.
Lens menu
The Lens menu provides access to the Lens Control setting and the 
Lens Center command.
Lens Control allows Zoom, Focus and Shift adjustment using the arrow buttons. 
The setting operates in Zoom/Focus Adjustment and Shift Adjustment mode.
Press ENTER/OK to switch between modes as follows:
• Zoom/Focus Adjustment...

page 20
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the image
Orientation
• This can be set from the Setup menu.
Highlight Orientation and choose from Desktop Front, Ceiling Front, Desktop Rear and Ceiling Rear.
Keystone
• This can be set from the Geometr y menu.
Picture
• Settings such as Brightness, Contrast and Gamma can be set from the Image menu.
• You can also set Brightness, Contrast or Gamma via the remote control by pressing and holding A LT while pressing BRI, CON or...

CONNECTION GUIDE4 
Rev C Februar y 2015 
HIGHlite Laser 3D Series
High Brightness Digital Video Projector  

Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs ........................................................................\
...............................23
Digital inputs and outputs ........................................................................................23
Analog inputs ............................................................................................................24
EDID on the DVI and VGA inputs...