Digital Projection Projector HIGHlite Laser 3D Series User Manual

							page 13
Installation and Quick-Start Guide
CHANGING THE LENS
Changing The Lens
The lens hood
There are two types of lens hood, short and long. 
The short lens hood is used with the following lenses:
Throw ratiosPart number
0.77 : 1 fixed lens110-808
1.16 : 1 fixed lens110-809
1.45 - 1.74 : 1 zoom lens110-803
1.74 - 2.17 : 1 zoom lens112-878
2.17 - 2.90 : 1 zoom lens113-852
2.90 - 4.34 : 1 zoom lens110-806
The long lens hood must be used with the following long throw lens:
Throw ratiosPart number
4.34 - 6.76 : 1 zoom lens110-807
Projector with short lens hood fittedProjector with long lens hood fitted
Notes
  Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
 Do not use the short lens hood 
with the long throw lens.
  The projector will not power on 
without the lens and lens hood fitted.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 14
Installation and Quick-Start Guide
CHANGING THE LENS
Inserting a new lens
1. Insert the lens into the lens aperture, making sure that the plug on the\
 zoom drive 
mechanism lines up with socket on the right of the lens aperture.
2. Rotate the lens clockwise until it clicks into place.
3. Secure the lens hood to the front of the projector with the screws.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
 Do not use the short lens hood 
with the long throw lens.
  The projector will not power on 
without the lens and lens hood fitted.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 15
Installation and Quick-Start Guide
CHANGING THE LENS
Removing the lens
1. Loosen the four screws securing the lens hood to the body of the project\
or. 
Remove the lens hood.
2. Push down the lens holder tab.
3. Rotate the lens anti-clockwise.
4. Pull the lens forward to remove it from the lens aperture.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
 The projector will not power on 
without the lens and lens hood fitted.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 16
Installation and Quick-Start Guide
CHANGING THE FILTERS
Changing The Filters
1. Loosen the screws holding the filter cover.
2. Remove the old filter.
3. Insert the new filter. Make sure the air flow arrow on the side of the 
filter panel points toward the projector, as shown in the illustration.
4. Replace the filter cover and tighten the screws
Notes
	 Before	changing	the	filters,	always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
	When	changing	the	filters,	avoid	using excessive force as this may 
damage the equipment.
  In a normal environment the filters 
should be changed every 2000 
hours.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 17
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
Wait until the self-test has completed and the STANDBY indicator on the projector control panel shows blue. The system will be off and 
the projector will be in STANDBY mode.
2. Press ON on the remote control or STBY on the control panel to switch the projector ON. The ON indicator on the control panel will show 
green, the system will light and the shutter will open.
Switching the projector off
1. Press OFF on the remote control or STBY on the control panel, then press again to confirm your choice. The ON indicator on the control 
panel will start flashing, the system will go out and the cooling fans will run for a short time until the projector enters STANDBY mode.
2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconn\
ect 
the power cable from the projector.
Notes
 See also Connecting The Power 
Supply  earlier in this guide.
 The self-test is running when all the 
LEDs on the control panel are lit.
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed.
 Handle the power cable carefully 
and avoid sharp bends. Do not 
use a damaged power cable.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 18
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Selecting an input signal or test pattern
Input signal
• Connect an image source to the projector. The signal should be automatically detected by the projector, and should be displayed within 
two or three seconds.
• If more than one signal is connected, then select the input you want to \
display:
• Press one of the input buttons on the remote control.
• Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input from the main menu, press ENTER/OK and then 
select an input signal using the UP and DOWN arrow buttons. Press ENTER/OK to confirm your choice.
Test pattern
To display a test pattern:
• Press TEST on the remote control. If necessary, press again to change the test pattern. Test patterns are displayed in the following order:
...Off, White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V Burst, H \
Burst, ColorBar...
• Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main menu, then select a test pattern using the LEFT 
and RIGHT arrow buttons.
Notes
 For full details of how to use the 
controls and the menu system, see 
the Operating Guide .
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 19
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or using the lens buttons on the 
remote control.
Lens menu
The Lens menu provides access to the Lens Control setting and the 
Lens Center command.
Lens Control allows Zoom, Focus and Shift adjustment using the arrow buttons. 
The setting operates in Zoom/Focus Adjustment and Shift Adjustment mode.
Press ENTER/OK to switch between modes as follows:
• Zoom/Focus Adjustment mode with the source 
image
• Shift Adjustment mode with the source image
• Zoom/Focus Adjustment mode with an 
alignment grid
• Shift Adjustment mode with an alignment grid
• Zoom/Focus Adjustment mode with an aspect 
test
• Shift Adjustment mode with an aspect test
• Zoom/Focus Adjustment mode with a screen 
layout pattern1.60:1 (16:10)
1.66:1
1.78:1 (16:9)
1.85:1
1.33:1 (4:3)
2.35:1
• Shift Adjustment mode with a screen layout 
pattern
...
Remote control
Use the lens buttons on the remote control to adjust zoom, focus and shi\
ft directly, 
without opening a menu.
LensControl
[Enter] ShiftAdjustment
Zoom
Focus
Lens Control
[Enter] Zoom/Focus Adjustment
Shift
Notes
 For full details of how to adjust 
the lens using the remote control, 
see Remote Control earlier in this 
guide.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015           
						

							page 20
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the image
Orientation
• This can be set from the Setup menu.
Highlight Orientation and choose from Desktop Front, Ceiling Front, Desktop Rear and Ceiling Rear.
Keystone
• This can be set from the Geometr y menu.
Picture
• Settings such as Brightness, Contrast and Gamma can be set from the Image menu.
• You can also set Brightness, Contrast or Gamma via the remote control by pressing and holding A LT while pressing BRI, CON or 
GAMMA respectively.
Notes
Setup menuOrientation
Geometr y menu Keystone
Image menu
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							CONNECTION GUIDE4 
Rev C Februar y 2015 
HIGHlite Laser 3D Series
High Brightness Digital Video Projector  
						

							Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs ........................................................................\
...............................23
Digital inputs and outputs ........................................................................................23
Analog inputs ............................................................................................................24
EDID on the DVI and VGA inputs .............................................................................25
Using HDMI/DVI switchers with the projector ........................................................25
3D connections .........................................................................................................26
3D sources up to 60Hz requiring frame doubling and left/right interleaving ...................26
Frame sequential 3D sources up to 120Hz .....................................................................26
Dual Pipe 3D .....................................................................................................\
..............26
3D Sync ......................................................................................................................27
3D Sync in .....................................................................................................\
..................27
3D Sync out  ....................................................................................................\
................27
Control Connections ........................................................................\
................28
LAN connection examples .......................................................................................29
RS232 connection example ......................................................................................30
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015