Digital Projection Projector HIGHlite Laser 3D Series User Manual

							page 33
Operating Guide
USING THE MENUS
Using The Menus
Opening the OSD
Access the various menus using either the projector control panel or the\
 remote 
control. On either device,
• press the MENU button.
The on-screen display (OSD) opens showing the list of available menus.\
Opening a menu
Move up and down the list using the 
UP and DOWN  arrow buttons. To open a menu,
• press ENTER on the control panel or OK on the remote control.
This guide refers to the above two buttons as ENTER/OK.
Exiting menus and closing the OSD
To go back to the previous page,
• press MENU.
When you reach the top level, pressing MENU will close the OSD.
Notes
On-screen display (OSD): top level 
(list of available menus)
Select Item
[Enter]Submenu [Menu]
Exit
TestPattern
Lens
Image
Color
Geometry
Input
OffHDMI1
EdgeBlend
3D
Laser
Setup
Information
Projector control panel
ENTER
ON
STANDBYMENU
INPUTSTBY
ERROR
SHUTTER
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFFON
ALT
LENSFOCUS ZOOM
IN
OUT IN
OUT
SHIFT
2
1 3
HDMI2DVI
DISPLAYPORTHD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3 D EYE PIPSWAP45 6
7 8 9 0
ALT
ADDR
Remote control
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 34
Operating Guide
USING THE MENUS
Inside a menu
When you open a menu, the page consists of the following elements:
• Title bar at the top 
Shows which menu (and sub-menu) you have accessed.
• Highlighted item
• Available and unavailable items 
Unavailable items appear a pale green color. Whether an item is available 
may depend on other settings.
• Text next to each item 
Shows whether the item:
• has a value that can be changed (shows the current value)
• opens a sub-menu (< Enter >)
• executes a command (< Execute >)
Accessing sub-menus
Use the UP  and DOWN  arrow buttons to highlight the sub-menu, then press 
ENTER/OK.
Executing commands
If the item contains a command, press ENTER/OK to execute it.
You may be asked for confirmation. Use the LEFT  and RIGHT  arrow 
buttons to select your answer and then press ENTER/OK.
Notes
 The highlighted item has white text 
on a blue background.
Inside a menu
Reset Everything
YesNo
Confirmation dialog
MENU>>Sub-menu>>
Select Item
Adjust[Menu]
Return
MenuItem
Unavailable Item
Slider
Sub-menu
Command
Highlighted Item
Value
Value
Numeric value
< Enter >
< Execute >Value
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 35
Operating Guide
USING THE MENUS
Editing projector settings
If the highlighted menu item is a setting with a list of values to choos\
e from, you 
can change the value in two different ways.
Choosing a value from a list
To access the list of values and then make a selection:
1. Highlight the menu item and press ENTER/OK.
2. On the new page that opens, use the UP  and DOWN  arrow buttons to 
highlight a value, then press ENTER/OK again. 
A green “check” symbol marks the current selection.
3. Press MENU to exit the list.
Changing the value without viewing the list
Some menu items allow you to switch to the next or previous value withou\
t 
viewing the list:
• press the LEFT  or RIGHT  arrow button.
Using a slider to set a value
Some parameters with a numeric value open a slider. To set such a parameter:
1. Press the LEFT  or RIGHT  arrow button, or ENTER/OK. The arrow 
buttons will open the slider and adjust the value at the same time. 
ENTER/OK will open the slider without altering the initial value.
2. Use the LEFT  and RIGHT  arrow buttons to move the slider.
3. When ready, press MENU to exit the slider.
Notes
 Some menu items may be 
unavailable due to settings in other 
menus. Unavailable menu items 
appear pale green.
List of values
Parameter 101
Slider
MENU>>
SelectItem
Adjust[
Menu] Return
Item
Unavailable Item
Item
Item
Item
Highlighted Item
CurrentValue
Value
Value
Highlighted Value
ValueValue
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 36
Operating Guide
USING THE PROJECTOR
Using The Projector
Main menu
• Input 
Press ENTER/OK to open the list of available inputs.
Use the UP  and DOWN  arrow buttons to select an input from the list, 
then press ENTER/OK to confirm your choice.
Press MENU to return to the main menu.
• Test Pattern 
Choose from:
...Off, White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V 
Burst, H Burst, ColorBar...
Use the LEFT  and RIGHT  arrow buttons to switch between values.
• Lens, Image, Color, Geometry, Edge Blend, 3D, Laser, Setup and 
Information 
Press ENTER/OK to open these sub-menus and access various settings.
SelectItem
[Enter]Execute [
Menu] Return
Input
HDMI2
VGA
COMP 1
COMP 2
DVIHDMI 1
HDBaseT
TestPattern
Lens
Image
Color
Geometry
Edge Blend
3D
Laser
Setup
Information SDI
Select
Item
[Enter]Submenu [Menu]
Exit
TestPattern
Lens
Image
Color
Geometry
Input
OffHDMI1
EdgeBlend
3D
Laser
Setup
Information
Notes
  See Signal Inputs  in the 
Connection Guide  for further 
information about the available 
inputs and connections.
  Selecting a test pattern hides the 
OSD. Pressing 
MENU then hides 
the test pattern and shows the OSD.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 37
Operating Guide
USING THE PROJECTOR
Lens menu
Lens Control
Lens Control settings operate in Zoom/Focus Adjustment and Shift 
Adjustment mode.
When in Zoom/Focus Adjustment mode:
• Use the UP and DOWN arrow buttons to adjust Zoom.
• Use the LEFT and RIGHT arrow buttons to adjust Focus.
When in Shift Adjustment mode, use the arrow buttons to adjust Shift.
Press ENTER/OK to switch between modes as follows:
• Zoom/Focus Adjustment mode with the source 
image
• Shift Adjustment mode with the source image
• Zoom/Focus Adjustment mode with an 
alignment grid
• Shift Adjustment mode with an alignment grid
• Zoom/Focus Adjustment mode with an aspect 
test
• Shift Adjustment mode with an aspect test
• Zoom/Focus Adjustment mode with a screen 
layout pattern1.60:1 (16:10)
1.66:1
1.78:1 (16:9)
1.85:1
1.33:1 (4:3)
2.35:1
• Shift Adjustment mode with a screen layout 
pattern
...
Lens Center
Highlight Lens Center and press ENTER/OK.
NotesLens>>
Select Item
[Menu]Return
LensCenter
LensControl

[Enter] Execute
LensControl
[Enter] ShiftAdjustment
Zoom
Focus
Lens Control
[Enter] Zoom/Focus Adjustment
Shift
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015           
						

							page 38
Operating Guide
USING THE PROJECTOR
Image menu
Brightness and Contrast
Highlight the setting you wish to edit, and then press ENTER/OK, or the LEFT  
or RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Image>>
Select Item
[Menu]Return
Contrast
Gamma
Adaptive Contrast
Saturation
Hue
Brightness 100100
Sharpness
Noise Reduction
Position andPhase
Resync
2.2
Off
100
0
0
100
< Execute >
Adjust
Notes
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 39
Operating Guide
USING THE PROJECTOR
Image menu continued from previous page
Gamma
Choose a de-gamma curve from 1.0, 1.8, 2.0, 2.2, 2.35 and 2.5.
Used correctly, the Gamma setting can improve contrast while maintaining good 
details for blacks and whites. 
If excess ambient light washes out the image and it is difficult to see details in dark 
areas, lower the Gamma setting to compensate. This improves contrast while 
maintaining good details for blacks. Conversely, if the image is washed out and 
unnatural, with excessive detail in black areas, increase the setting.
Adaptive Contrast
Set to On to expand the light and dark portions of the contrast curve of the imag\
e, 
depending on the mean luminance of the image.
Saturation, Hue, Sharpness and Noise Reduction
Highlight the setting you wish to edit, and then press ENTER/OK, or the LEFT  
or RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Notes
SelectItem
[Enter]Execute [Menu]
Return
Brightness
1.8
2.0
2.2
2.35 2.51.0Contrast
Gamma
Adaptive Contrast
Saturation
Hue
Sharpness
Noise Reduction
Position andPhase
Resync
Image >>
Select Item
[Enter]Execute [Menu]
Return
Brightness
OnOffContrast
Gamma
AdaptiveContrast
Saturation
Hue
Sharpness
Noise Reduction
Position andPhase
Resync
Image >>
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 40
Operating Guide
USING THE PROJECTOR
Image menu continued from previous page
Position and Phase
Press ENTER/OK to open the submenu.
• V Position and H Position 
Set the sliders as required.
• Phase 
Adjusts the phase of the pixel sampling clock relative to the incoming 
signal. Adjust the phase if noise is visible.
• Tracking 
Adjusts the frequency of the pixel sampling clock. Flicker or vertical 
banding indicate poor tracking.
• Sync Level 
Adjusts the voltage level of the signal detection circuitry. Adjust if the 
projector loses sync during scenes where the signal drops below black.
Highlight the setting you wish to edit, and then press ENTER/OK, or the LEFT 
 or RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Resync
Press ENTER/OK to force the projector to resynchronize with the current 
input.
Image>>Position andPhase
Select Item
[Menu]Return
HPosition
Phase
Tracking
Sync Level
VPosition
100100
– –––
– –––
– –––
Adjust
Image >>
Select Item
[Menu]Return
Contrast
Gamma
Adaptive Contrast
Saturation
Hue
Brightness
100100
Sharpness
Noise Reduction
Position andPhase
Resync
2.2
Off
100
0
0
100
<
Execute >
Adjust
Notes
 Some of the settings within the 
Position and Phase sub-menu, 
Phase, Tracking and Sync Level, 
affect only VGA input source. These 
settings are not available if the 
projector is using a different source.
  Adjust the Phase after adjusting 
Tracking.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 41
Operating Guide
USING THE PROJECTOR
Color menu
Color Space
In most cases, the Auto setting determines the correct colorspace to use. If it does 
not, you can choose a specific colorspace:
Choose from Auto, YPbPr, YCbCr, RGB PC and RGB Video.
NotesColor>>
Select Item
Adjust[Menu]
Return
ColorGamut
User Gamut
Red Lift
Green Lift
Blue Lift
Color Space
Native100
100
100
Red Gain 100
Color
Temperature
Green Gain
Blue Gain 100
100
Auto
Native
Color >>
Select Item
[Enter]Execute [
Menu] Return
ColorTemperature
Color Gamut
User Gamut
Red Lift
Blue Lift
Color Space
YPbPr
YCbCr
RGB PC
RGB VideoAuto
Green Lift
Red Gain
Green Gain
Blue Gain
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 42
Operating Guide
USING THE PROJECTOR
Color menu continued from previous page 
Color Temperature
Choose a value from 3200K (warmer) to 9300K (cooler) or Native (no 
correction).
NotesColor>>
Select Item
[Enter]Execute [
Menu] Return
ColorTemperature
Color Gamut
User Gamut
Red Lift
Blue Lift
Color
Space
5500K
6500K
7500K
9300K
3200K
GreenLift
Red Gain
Green Gain
Blue Gain Native
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015