Digital Projection Projector HIGHlite Laser 3D Series User Manual

							page 3
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
What’s In The Box?Notes
 Make sure your box contains 
everything listed. If any pieces are 
missing, contact your dealer.
 Only one remote will be supplied 
with the projector. For more 
information, see  Remote Control 
further in this guide.
  You should save the original box 
and packing materials, in case you 
ever need to ship your projector.
 The projector is shipped without a 
lens.
 Do not use the short lens hood 
with the long throw lens.
  For further information about using 
the right lens and hood, see  The 
lens hood  further in this guide.
 Only one power cable - dependent 
on the destination territory - will be 
supplied with the projector.
Remote control 
(116-088)
2x AAA batteries
User Manual on disc 
(115-759)
Important Information (114-914)
Power cable, Europe 
(112-001)
Power cable, North America 
(112-002)
Projector
Power cable, United Kingdom 
(112-000)
VGA cable
SHUTTER
OPEN CLOSEMENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOMIN
OUT IN
OUT
SHIFT
2
1 3HDMI2DVIDISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3 D EYE PIPSWAP45 6
7 8 9 0
ALT
ADDR
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 4
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Connecting The Power Supply
Lift the cable lock up, push the mains connector in firmly and 
push the lock down to secure the cable.
1 AC mains inlet with cable lock
Notes
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed.
 Handle the power cable carefully 
and avoid sharp bends. Do not 
use a damaged power cable.
1
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 5
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Projector Over view
Front and rear views
1 Control panel
2 Connection panel
3 Air outlet
4 Lens hood
5 Front infrared window
6 Power switch and power connection
7 Air outlet
8 Rear infrared window
9 Air inlet
10 Adjustable feet
Notes
 Do not use the short lens hood 
with the long throw lens.
  For further information about using 
the right lens and hood, see  The 
lens hood  further in this guide.
Front view
45
312
6
Rear view
78
10
9
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 6
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Control panel
1 ON indicator (green)
 Behavior  Meaning
 Off     The projector is switched off.
 Flashing     The projector is warming up or cooling down.
 On    The projector is switched on (Normal mode).
2 ERROR indicator (red)
 Behavior    Meaning
 Flash three times, then pause    Fan failure.
 Flash four times, then pause    Over temperature.
 Flash five times, then pause    Filter failure.
 On      System error.
3 ENTER button
Confirm your choice when navigating the OSD.
Access the Lens Control setting: shift the lens, zoom and focus the image.
4 Arrow buttons
Navigate the OSD, edit settings.
5 STANDBY indicator (blue)
 Behavior  Meaning
 On     The projector is in STANDBY mode.
6 MENU button
Access the projector OSD (on-screen display).
7 INPUT button
Select input source.
8 STBY button
Switch the projector on and off (in STANDBY mode)
ENTER
ON
STANDBYMENU
INPUT
STBY
ERROR
1
62
4
57
8
3
Notes
 
During startup all LEDs light up 
at the same time to indicate the 
projector is carrying out a self-test.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 7
Installation and Quick-Start Guide
REMOTE CONTROL
Remote Control
1 Power ON / OFF
2 Shutter OPEN / CLOSE
3 MENU
Access the projector OSD (on-screen display). If the OSD is open, pres\
s this button to 
go back to the previous menu.
4 Navigation
Navigate through the menus with the arrows, confirm your choice with OK.
In LENS SHIFT mode the arrows are used to move the lens. See 7 below.
5 EXIT
Close the OSD.
6 Focus IN / OUT
Adjust focus.
7 SHIFT
Press and hold this button, then press the Navigation arrow buttons to move the lens.
8 INFO
Access information about the projector.
9 Zoom IN / OUT
Adjust zoom.
continues on next page...
Notes
Remote control
SHUTTER
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENSFOCUS ZOOM
IN
OUT IN
OUT
SHIFT
2
1 3
HDMI2DVI
DISPLAYPORTHD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3 D EYE PIPSWAP
45 6
7 8 9 0
ALT
ADDR
1
2
4
5
9
3
8
6
7
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 8
Installation and Quick-Start Guide
REMOTE CONTROL
10 A LT
Press and hold this button to access alternative functions for all 
buttons with a green label.
11 HDMI 1 / BRI / numeric input 1
Select the HDMI 1 input.
Use with A LT to bring up the Brightness control, then adjust the 
value with the LEFT and RIGHT arrow buttons.
12 HDMI 2 / CON / numeric input 2
Select the HDMI 1 input.
Use with A LT to bring up the Contrast control, then adjust the value 
with the LEFT and RIGHT arrow buttons.
13 DVI / GAMMA / numeric input 3
Select the DVI input.
Use with A LT to switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
14 DISPLAYPORT / R / numeric input 4
Use with A LT to switch the red DMD on and off. This functionality is 
disabled when the projector is showing a test pattern.
15 HD-T / G / numeric input 5
Select the HDBaseT input.
Use with A LT to switch the green DMD on and off. This functionality is 
disabled when the projector is showing a test pattern.
16 3GSDI / B / numeric input 6
Select the 3G-SDI input.
Use with A LT to switch the blue DMD on and off. This functionality is 
disabled when the projector is showing a test pattern.
continues on next page...
Notes
 DISPLAYPORT is not available on 
this projector.
Remote control
SHUTTER
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFFON
ALT
LENSFOCUS ZOOM
IN
OUT IN
OUT
SHIFT
2
1 3
HDMI2DVI
DISPLAYPORTHD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3 D EYE PIPSWAP
45 6
7 8 9 0
ALT
ADDR
16
12
15
14
10
13
11
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 9
Installation and Quick-Start Guide
REMOTE CONTROL
17 VGA / 3D / numeric input 7
Select the VGA input.
Use with A LT to toggle the 3D Format setting between Off and Auto.
18 COMP1 / EYE / numeric input 8
Select the Component 1 input. 
Use with A LT to switch between left and right eye 3D dominance.
19 COMP2 / PIP / numeric input 9
Select the Component 2 input.
20 TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard, 
CrossHatch, V Burst, H Burst, ColorBar...
21 ADDR / ALL
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts flashing.
2. Release this button and while the indicator is still flashing, enter 
a two-digit address using the numeric input buttons. The indicator 
will flash three times quickly to confirm the change.
To unassign an address and return to the default address 00,
• Press and hold A LT and this button simultaneously until the 
indicator flashes to confirm the change.
Remote control
SHUTTER
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFFON
ALT
LENSFOCUS ZOOM
IN
OUT IN
OUT
SHIFT
2
1 3
HDMI2DVI
DISPLAYPORTHD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3 D EYE PIPSWAP
45 6
7 8 9 0
ALT
ADDR
21
18
19
17
20
Notes
 PIP and SWAP are not available on 
this projector.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 10
Installation and Quick-Start Guide
REMOTE CONTROL
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is \
within the angle of 
acceptance when trying to control the projector.
40°
40°
Infrared reception
Notes
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 11
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing\
 by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that 
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the fixing holes for ceiling mounting.
1 Four adjustable feet
2 Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into 
the body of the projector.
Notes
 Always allow the projector 
to cool for 5 minutes before 
disconnecting the power or 
moving the projector.
 Ensure that there is at least 30 
cm (12 in) of space between the 
ventilation outlets and any wall, 
and 10 cm (4 in) on all other 
sides.
 Do not stack more than 3 
projectors.1
2
1
1
1
2
2
2
2
2
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 12
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Roll and pitch
The projector can be operated in numerous positions.
The only non-workable angle is in portrait mode with inputs facing upwar\
d, as shown in the diagram.
1 Non-workable angle
2 Workable angles
Notes
360°2
Pitch
30°
330°
2
1
Roll
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015