Digital Projection Projector HIGHlite Laser 3D Series User Manual

							page 113
Reference Guide
APPENDIX E: WIRING DETAILS
Appendix E: Wiring Details
Signal inputs and outputs
VGA
15 way D-type connector
1 R
2 G
3 B
4 unused
5 Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5V
10 Digital Ground (V Sync/DDC)
1 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
Notes
VGA: pin view of female connector
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 114
Reference Guide
APPENDIX E: WIRING DETAILS
HDMI 1 and 2
19 way type A connector
1 TMDS Data 2+
2 TMDS Data 2 Shield
3 TMDS Data 2-
4 TMDS Data 1+
5 TMDS Data 1 Shield
6 TMDS Data 1-
7 TMDS Data 0+
8 TMDS Data 0 Shield
9 TMDS Data 0-
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock-
13 CEC
14 not connected
15 SCL (DDC Clock)
16 SCA (DDC Data)
17 DDC/CEC Ground
18 +5 V Power
19 Hot Plug Detect
HDMI: pin view of panel connector
Notes
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 115
Reference Guide
APPENDIX E: WIRING DETAILS
DVI
24 way D-type connector
Pin 1  TMDS data 2−     Digital red− (link 1)  
Pin 2  TMDS data 2+     Digital red+ (link 1)  
Pin 3  TMDS data 2/4 shield    
Pin 4  TMDS data 4−     Digital green− (link 2)  
Pin 5  TMDS data 4+     Digital green+ (link 2)  
Pin 6  DDC clock    
Pin 7  DDC data    
Pin 8  Analog vertical sync    
Pin 9  TMDS data 1−     Digital green− (link 1)  
Pin 10  TMDS data 1+     Digital green+ (link 1)  
Pin 11  TMDS data 1/3 shield    
Pin 12  TMDS data 3-     Digital blue− (link 2)  
Pin 13  TMDS data 3+     Digital blue+ (link 2)  
Pin 14  +5 V       Power for monitor when in standby  
Pin 15  Ground       Return for pin 14 and analog sync  
Pin 16  Hot plug detect    
Pin 17  TMDS data 0−     Digital blue− (link 1) and digital sync  
Pin 18  TMDS data 0+     Digital blue+ (link 1) and digital sync  
Pin 19  TMDS data 0/5 shield    
Pin 20  TMDS data 5−     Digital red− (link 2)  
Pin 21  TMDS data 5+     Digital red+ (link 2)  
Pin 22  TMDS clock shield    
Pin 23  TMDS clock+     Digital clock+ (links 1 and 2)  
Pin 24  TMDS clock−     Digital clock− (links 1 and 2)  
C1  Analog red      
C2  Analog green      
C3  Analog blue      
C4  Analog horizontal sync      
C5  Analog ground     Return for R, G, and B signals
DVI:  pin view of female connector
Notes
 High-bandwidth Digital Content 
Protection (HDCP) is supported on 
this input.
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 116
Reference Guide
APPENDIX E: WIRING DETAILS
3G-SDI In, 3G-SDI Out
75 ohm BNC
Component 1
3 x RCA Phono connector
Component 2
3 x 75 ohm BNC connector
RGsBYCbCrYPbPr
RCrPr
G + SyncGY
BCbPb
HDBaseT input
RJ45 socket.
3G-SDI connector
Notes
 3G-SDI signals are very high 
speed digital signals which require 
better quality coaxial cable than 
conventional analogue video. The 
data rate is 3 Gigabits per second.
  In choosing cable length and 
connectors for any installation the 
frequency response loss in decibels 
should be proportional to √f, from 1 
MHz, to 3 GHz.
 High-bandwidth Digital Content 
Protection (HDCP) is supported on 
this input.
Component 1: 
3 x RCA Phono connector
Component 2: 
3 x 75 ohm BNC connector
HDBaseT input
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 117
Reference Guide
APPENDIX E: WIRING DETAILS
Control connections
LAN
RJ45 socket
RS232
9 way D-type connector
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
Notes
 Only one remote connection (RS232 
or LAN) should be used at any one 
time.
Update port
RS232:  
pin view of female connector
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 118
Reference Guide
APPENDIX E: WIRING DETAILS
Trigger 1 & Trigger 2
3.5 mm mini jack
Tip Signal
Sleeve Ground
IR input
3.5 mm mini jack
Tip Signal
Ring Not connected
Sleeve Ground
USB
USB type A socket
Pin 1     VCC (+5 V)  
Pin 2    Data−  
Pin 3    Data+  
Pin 4    Ground
3D Sync IN and 3D Sync OUT
75 ohm BNC
TipSleeveNotes
Sleeve
Ring
Tip
USB port: 
pin view of female connector
pin view of female connector
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 119
Reference Guide
APPENDIX F: GLOSSARY OF TERMS
Appendix F: Glossar y Of  Terms
1080p
An HDTV resolution which corresponds to 1920 x 1080 pixels (a widescreen aspect ratio of 16:9).
3D active glasses
Wireless battery-powered glasses with LCD shutters. Synchronization info\
rmation is communicated to the glasses by means of an infrared 
(IR) or radio frequency (RF) emitter which is connected to the Sync Out terminal on the projector. IR or RF pulses are transmitted by the 
emitter to signal when the left eye and right eye images are being displ\
ayed. The glasses incorporate a sensor which detects the emitter’s 
signal and synchronises the left and right eye shutters with the project\
ed image.
3D passive glasses
Passive glasses do not require a power source to work. Light with left-hand polarisation can pass through the left lens and light with right-
hand polarisation can pass through the right-hand lens. These glasses are used in conjunction with another device which polarize\
s the image, 
such as a ZScreen.
Adjust lines
A pattern applied to the image where its edge is to be blended with anoth\
er image. Adjust lines are used to position the projectors in the array 
during the edge blend process.
Anamorphic lens
A special lens which, when used with the TheaterScope aspect ratio, allows watching 2.35:1 content packed in a 16:9 source.
Aperture
The opening of the lens that determines the angle through which light tr\
avels to come into focus.
Notes
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 120
Reference Guide
APPENDIX F: GLOSSARY OF TERMS
Aspect ratio
The proportional relationship between the width and the height of the projected image. It is represented by two numbers separated by a colon, 
indicating the ratio of image width and height respectively: for example\
, 16:9 or 2.35:1.
Not to be confused with resolution.
Blanking (projection)
The ability to intentionally turn off, that is, set to black, areas around the edges of the projected image.\
 It is sometimes referred to as “curtains” 
since it can be used to blank an area of image that literally falls on t\
he curtains at the side of the screen in a movie theater. Usually no image 
resizing or geometric correction takes place and the “blanked” par\
t of the image is lost.
Not to be confused with horizontal and vertical blanking (video signal).
Blanking (video signal)
The section of the video signal where there is no active video data.
Not to be confused with blanking (projection).
Blend region
The area of the image that is to overlap with another image in an edge blend setup. Sometimes called overlapping region.
Brightness (electronic control)
A control which adds a fixed intensity value to every pixel in the display, moving the entire range of displayed intensities up or down, and is 
used to set the black point in the image (see Contrast). In Component Video signals, brightness is the same as luminance.
Brightness (optical)
Describes how ‘bright’ an image that is projected onto a screen appears to an observer.
C
See Chrominance.
Notes
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 121
Reference Guide
APPENDIX F: GLOSSARY OF TERMS
Chrominance
Also known as ‘C’, this is the component, or pair of components, of a Component Video signal which describes color difference information.
Color difference
In Component Video signals, the difference between specified colors and the luminance component. Color difference is zero for 
monochrome images.
Color gamut
The spectrum of color available to be displayed.
Color temperature
The position along the black body curve on the chromaticity diagram, normally quoted in Kelvin. It takes into account the preset values for 
color balance in the service set-up to take up the variations in the pri\
sm. The projector allows you to adjust this temperature (i.e. adjust the 
picture color temperature).
Component video
A three-wire or four-wire video interface that carries the signal split i\
nto its basic RGB components or luminance (brightness) and two-color-
difference signals (YUV) and synchronization signals.
Contrast (electronic control)
The adjustment of the white point of the image without affecting the black point. This increases the intensity range of the displayed image.
Contrast (optical)
The intensity difference between the darkest and lightest areas of the screen.
Cr, Cb
Color difference signals used with ‘Y’ for digital Component Video inputs. They provide information about the signal color. Not to be 
confused with Pr, Pb.
Notes
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  
						

							page 122
Reference Guide
APPENDIX F: GLOSSARY OF TERMS
Crop
Remove part of the projected image.
Alternatively, fit an image into a frame with a different aspect ratio by removing part of the image. The image is resized so that either its 
length or its width equals the length or width of the frame, while the other dimension has moved outside the frame; the excess area is then cut 
out.
Dark time
The time inserted between frames when using 3D active glasses, to avoid ghosting caused by switching time between left and right eye.
DDC (Display Data Channel)
A communications link between the source and projector. DDC is used on the HDMI, DVI and VGA inputs. The link is used by the source to 
read the EDID stored in the projector.
Deinterlacing
The process of converting interlaced video signals into progressive ones.
DHCP	(Dynamic	Host	Configuration	Protocol)
A network protocol that is used to configure network devices so that they can communicate on an IP network, for example by allocating an IP 
address.
DMD™ (Digital Micromirror Device™)
The optical tool that transforms the electronic signal from the input so\
urce into an optical image projected on the screen. The DMD™ of a 
projector has a fixed resolution, which affects the aspect ratio of the projected image.
A Digital Micromirror Device™ (DMD™) consists of moving microscop\
ic mirrors. Each mirror, which acts as a pixel, is suspended between 
two posts by a thin torsion hinge. It can be tilted to produce either a \
bright or dark pixel.
Edge blend
A method of creating a combined image by blending the adjoining edges of \
two or more individual images.
Notes
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015