Digital Projection Projector HIGHlite Laser 3D Series User Manual

page 33
Operating Guide
USING THE MENUS
Using The Menus
Opening the OSD
Access the various menus using either the projector control panel or the\
 remote 
control. On either device,
• press the MENU button.
The on-screen display (OSD) opens showing the list of available menus.\
Opening a menu
Move up and down the list using the 
UP and DOWN  arrow buttons. To open a menu,
• press ENTER on the control panel or OK on the remote control.
This guide refers to the above two buttons as ENTER/OK.
Exiting menus...

page 34
Operating Guide
USING THE MENUS
Inside a menu
When you open a menu, the page consists of the following elements:
• Title bar at the top 
Shows which menu (and sub-menu) you have accessed.
• Highlighted item
• Available and unavailable items 
Unavailable items appear a pale green color. Whether an item is available 
may depend on other settings.
• Text next to each item 
Shows whether the item:
• has a value that can be changed (shows the current value)
• opens a sub-menu (< Enter >)
• executes a...

page 35
Operating Guide
USING THE MENUS
Editing projector settings
If the highlighted menu item is a setting with a list of values to choos\
e from, you 
can change the value in two different ways.
Choosing a value from a list
To access the list of values and then make a selection:
1. Highlight the menu item and press ENTER/OK.
2. On the new page that opens, use the UP  and DOWN  arrow buttons to 
highlight a value, then press ENTER/OK again. 
A green “check” symbol marks the current selection.
3. Press...

page 36
Operating Guide
USING THE PROJECTOR
Using The Projector
Main menu
• Input 
Press ENTER/OK to open the list of available inputs.
Use the UP  and DOWN  arrow buttons to select an input from the list, 
then press ENTER/OK to confirm your choice.
Press MENU to return to the main menu.
• Test Pattern 
Choose from:
...Off, White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V 
Burst, H Burst, ColorBar...
Use the LEFT  and RIGHT  arrow buttons to switch between values.
• Lens, Image, Color,...

page 37
Operating Guide
USING THE PROJECTOR
Lens menu
Lens Control
Lens Control settings operate in Zoom/Focus Adjustment and Shift 
Adjustment mode.
When in Zoom/Focus Adjustment mode:
• Use the UP and DOWN arrow buttons to adjust Zoom.
• Use the LEFT and RIGHT arrow buttons to adjust Focus.
When in Shift Adjustment mode, use the arrow buttons to adjust Shift.
Press ENTER/OK to switch between modes as follows:
• Zoom/Focus Adjustment mode with the source 
image
• Shift Adjustment mode with the source...

page 38
Operating Guide
USING THE PROJECTOR
Image menu
Brightness and Contrast
Highlight the setting you wish to edit, and then press ENTER/OK, or the LEFT  
or RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Image>>
Select Item
[Menu]Return
Contrast
Gamma
Adaptive Contrast
Saturation
Hue
Brightness 100100
Sharpness
Noise Reduction
Position andPhase
Resync
2.2
Off
100
0
0
100
< Execute >
Adjust
Notes
   
Digital...

page 39
Operating Guide
USING THE PROJECTOR
Image menu continued from previous page
Gamma
Choose a de-gamma curve from 1.0, 1.8, 2.0, 2.2, 2.35 and 2.5.
Used correctly, the Gamma setting can improve contrast while maintaining good 
details for blacks and whites. 
If excess ambient light washes out the image and it is difficult to see details in dark 
areas, lower the Gamma setting to compensate. This improves contrast while 
maintaining good details for blacks. Conversely, if the image is washed out and...

page 40
Operating Guide
USING THE PROJECTOR
Image menu continued from previous page
Position and Phase
Press ENTER/OK to open the submenu.
• V Position and H Position 
Set the sliders as required.
• Phase 
Adjusts the phase of the pixel sampling clock relative to the incoming 
signal. Adjust the phase if noise is visible.
• Tracking 
Adjusts the frequency of the pixel sampling clock. Flicker or vertical 
banding indicate poor tracking.
• Sync Level 
Adjusts the voltage level of the signal detection...

page 41
Operating Guide
USING THE PROJECTOR
Color menu
Color Space
In most cases, the Auto setting determines the correct colorspace to use. If it does 
not, you can choose a specific colorspace:
Choose from Auto, YPbPr, YCbCr, RGB PC and RGB Video.
NotesColor>>
Select Item
Adjust[Menu]
Return
ColorGamut
User Gamut
Red Lift
Green Lift
Blue Lift
Color Space
Native100
100
100
Red Gain 100
Color
Temperature
Green Gain
Blue Gain 100
100
Auto
Native
Color >>
Select Item
[Enter]Execute [
Menu] Return...

page 42
Operating Guide
USING THE PROJECTOR
Color menu continued from previous page 
Color Temperature
Choose a value from 3200K (warmer) to 9300K (cooler) or Native (no 
correction).
NotesColor>>
Select Item
[Enter]Execute [
Menu] Return
ColorTemperature
Color Gamut
User Gamut
Red Lift
Blue Lift
Color
Space
5500K
6500K
7500K
9300K
3200K
GreenLift
Red Gain
Green Gain
Blue Gain Native
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015