Digital Projection Projector HIGHlite Laser 3D Series User Manual

page 3
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
What’s In The Box?Notes
 Make sure your box contains 
everything listed. If any pieces are 
missing, contact your dealer.
 Only one remote will be supplied 
with the projector. For more 
information, see  Remote Control 
further in this guide.
  You should save the original box 
and packing materials, in case you 
ever need to ship your projector.
 The projector is shipped without a 
lens.
 Do not use the short lens hood 
with the long throw...

page 4
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Connecting The Power Supply
Lift the cable lock up, push the mains connector in firmly and 
push the lock down to secure the cable.
1 AC mains inlet with cable lock
Notes
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed.
 Handle the power cable carefully 
and avoid sharp bends. Do not 
use a damaged power cable.
1
   
Digital Projection HIGHlite Laser 3D...

page 5
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Projector Over view
Front and rear views
1 Control panel
2 Connection panel
3 Air outlet
4 Lens hood
5 Front infrared window
6 Power switch and power connection
7 Air outlet
8 Rear infrared window
9 Air inlet
10 Adjustable feet
Notes
 Do not use the short lens hood 
with the long throw lens.
  For further information about using 
the right lens and hood, see  The 
lens hood  further in this guide.
Front view
45
312
6
Rear view
78
10
9...

page 6
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Control panel
1 ON indicator (green)
 Behavior  Meaning
 Off     The projector is switched off.
 Flashing     The projector is warming up or cooling down.
 On    The projector is switched on (Normal mode).
2 ERROR indicator (red)
 Behavior    Meaning
 Flash three times, then pause    Fan failure.
 Flash four times, then pause    Over temperature.
 Flash five times, then pause    Filter failure.
 On      System error.
3 ENTER button
Confirm your...

page 7
Installation and Quick-Start Guide
REMOTE CONTROL
Remote Control
1 Power ON / OFF
2 Shutter OPEN / CLOSE
3 MENU
Access the projector OSD (on-screen display). If the OSD is open, pres\
s this button to 
go back to the previous menu.
4 Navigation
Navigate through the menus with the arrows, confirm your choice with OK.
In LENS SHIFT mode the arrows are used to move the lens. See 7 below.
5 EXIT
Close the OSD.
6 Focus IN / OUT
Adjust focus.
7 SHIFT
Press and hold this button, then press the Navigation...

page 8
Installation and Quick-Start Guide
REMOTE CONTROL
10 A LT
Press and hold this button to access alternative functions for all 
buttons with a green label.
11 HDMI 1 / BRI / numeric input 1
Select the HDMI 1 input.
Use with A LT to bring up the Brightness control, then adjust the 
value with the LEFT and RIGHT arrow buttons.
12 HDMI 2 / CON / numeric input 2
Select the HDMI 1 input.
Use with A LT to bring up the Contrast control, then adjust the value 
with the LEFT and RIGHT arrow buttons.
13 DVI /...

page 9
Installation and Quick-Start Guide
REMOTE CONTROL
17 VGA / 3D / numeric input 7
Select the VGA input.
Use with A LT to toggle the 3D Format setting between Off and Auto.
18 COMP1 / EYE / numeric input 8
Select the Component 1 input. 
Use with A LT to switch between left and right eye 3D dominance.
19 COMP2 / PIP / numeric input 9
Select the Component 2 input.
20 TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue,...

page 10
Installation and Quick-Start Guide
REMOTE CONTROL
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is \
within the angle of 
acceptance when trying to control the projector.
40°
40°
Infrared reception
Notes
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015  

page 11
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing\
 by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that 
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the fixing...

page 12
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Roll and pitch
The projector can be operated in numerous positions.
The only non-workable angle is in portrait mode with inputs facing upwar\
d, as shown in the diagram.
1 Non-workable angle
2 Workable angles
Notes
360°2
Pitch
30°
330°
2
1
Roll
   
Digital Projection HIGHlite Laser 3D Series 
Rev C Februar y 2015