Digital Projection Projector HIGHlite Laser 3D Series User Manual

page 53
Operating Guide
USING THE PROJECTOR
Geometry menu continued from previous page
Corners
For each corner, apply horizontal and / or vertical correction as necessary to 
restore the rectangular shape of the image.
Top Right Cor ner example
In this illustration, the top right corner requires both horizontal and vertical 
correction.
SelectItem
[Menu] Return
Geometry >>
Overscan
Keystone
Rotation
Pincushion /Barrel
Top Left Corner
Aspect
Ratio
Off
16:10
Top
Right Corner
Bottom LeftCorner
Bottom...

page 54
Operating Guide
USING THE PROJECTOR
Geometry menu continued from previous page
Reset
This command allows you to reset all Geometr y settings apart from Blanking 
and restore the factory default values.
SelectItem
[Menu]Return
Geometry >>
Overscan
Keystone
Rotation
Pincushion /Barrel
Top Left Corner
Aspect
Ratio
Off
16:10
Top Right Corner
Bottom LeftCorner
Bottom RightCorner
Reset
Blanking
[Enter] Execute
Notes
 The Reset command does not apply 
to 
Blanking settings. The Blanking 
submenu...

page 55
Operating Guide
USING THE PROJECTOR
Geometry menu continued from previous page
Blanking
Select the edge you wish to blank and use the LEFT  and RIGHT  arrow 
buttons to determine the amount of correction.
Use the Reset command to restore blanked edges.
Geometry>>Blanking >>
SelectItem
[Menu]Return
Bottom
Left
Right
Reset
Top
00
0
0
< Execute >
Adjust
Notes
 Blanking corrections are 
unavailable when using any of the 
following:
• Keystone
• Rotation
• Pincushion / Barrel
• Black Level Uplift...

page 56
Operating Guide
USING THE PROJECTOR
Edge Blend menu
• Edge Blend 
Enable and disable Edge Blend
• Align Pattern 
When switched on, this feature makes the overlaps more visible and helps\
 
adjust the physical position of the projectors in the array.
• Blend Width 
Determine the width of the blended regions.
• Black Level Uplift 
Adjust black levels to compensate if the blended regions appear brighter\
 than 
the rest of the image.
• Reset 
Reset all Edge Blend settings to their factory default...

page 57
Operating Guide
USING THE PROJECTOR
Edge Blend menu continued from previous page
Blend Width
Use the LEFT  and RIGHT  arrow buttons to set the width of the blended 
regions:
1 To p
2 Bottom
3 Left
4 Right
Notes
 Some controls in the Edge 
Blend
 menu may be unavailable 
depending on other settings. For 
more information, see  Possible 
Geometry and Edge Blend 
combinations  further in this guide.
EdgeBlend >>Blend Width>>
Select Item
[Menu]Return
Bottom
Left
Right
Top
00
0
0
Adjust
3
12
4...

page 58
Operating Guide
USING THE PROJECTOR
Edge Blend menu continued from previous page
Black Level Uplift
Black in the blended regions appears less dark than in the rest of the i\
mage.
Use this menu to raise black levels in the unblended regions to achieve \
a uniform 
black level.
Black level uplift is available for up to two edges, and they must be op\
posite each 
other. For example, you can set black level to To p and Bottom, or to Left and 
Right, but not to To p and Left.
1. Select Area
Stray...

page 59
Operating Guide
USING THE PROJECTOR
Possible Geometr y and Edge Blend combinations
Some Geometr y and Edge Blend settings cannot be used in combination with others. The table below shows the possible combinations:
KeystoneRotationPincushion / 
BarrelCornersBlanking2-side blend4-side blendBlack Level 
Uplift
Keystone
Rotation
Pincushion / Barrel
Cornersüüü
Blankingüüü
2-side blendüüü
4-side blendüü
Black Level Upliftü
Notes
   
Digital Projection HIGHlite...

page 60
Operating Guide
USING THE PROJECTOR
3D menu
Use this menu to enable, disable and set up 3D input, as follows:
• 3D Format — Off, Auto, Side by Side (Half), Top and Bottom and 
Dual-Pipe.
• 3D Swap — Normal and Rever se (set to Rever se if the left- and right-eye 
images are displayed in the wrong order)
• Dark Time — 0.65 ms, 1.3 ms, 1.95 ms and 2.5 ms. Set to reduce the 
effect of images overlapping while the glasses are switching
• Sync Offset — use the LEFT  and RIGHT  arrow buttons to...

page 61
Operating Guide
USING THE PROJECTOR
3D menu continued from previous page 
3D types
In most situations you can use the Auto setting to have the projector automatically detect the 
format. Otherwise, consider the notes below to help you set up the 3D in\
put manually.
The following 3D formats are supported:
• Dual-Pipe (LEFT and RIGHT) 
The left and right eye images are delivered on two separate HDMI links, \
which the projector 
will interleave for 3D display.
• Frame Packing 
This format will be...

page 62
Operating Guide
USING THE PROJECTOR
3D menu continued from previous page
Some 3D settings explained
Dark Time
Ghosting can be caused by the left and right images 
overlapping during the time that the ZScreen or 3D 
glasses are switching. Dark Time allows you to 
minimize this effect.
3D Swap
The outgoing 3D frames are in pairs - the dominant 
frame being presented first. You can determine which 
frame should be the dominant one.
By convention the default setting is Left.
Sync Offset
The sync...