Digital Projection Projector HIGHlite Cine 330 3D Series User Manual

OPERATING GUIDE4 
Rev E August 2014 
HIGHlite Cine 330 3D Series
 High Brightness Digital Video Projector  

Operating Guide
IN THIS GUIDE
IN THIS GUIDE
Using The Menus ........................................................................\
................25
Opening the OSD .........................................................................................25
Opening a menu ..........................................................................................25
Exiting menus and closing the OSD 
..........................................................25
Inside a menu...

page 25
Operating Guide
USING THE MENUS
Using The Menus
Opening the OSD
Access the various menus using either the projector control panel or the\
 
remote control. On either device,
• press the MENU button.
The on-screen display (OSD) opens showing the list of available menus.\
Opening a menu
Move up and down the list using the UP and DOWN  arrow buttons. 
To open a menu,
• press ENTER (on the remote control) or SELECT (on the control panel).
This guide refers to the above two buttons as ENTER/SELECT....

page 26
Operating Guide
USING THE MENUS
Inside a menu
When you open a menu, the page consists of the following elements:
• Title bar at the top 
Shows which menu (and sub-menu) you have accessed.
• Highlighted item
• Available and unavailable items 
Unavailable items appear grayed out. Whether an item is available may 
depend on other settings.
• Text next to each item 
Shows whether the item:
• has a value that can be changed (shows the current value)
• opens a sub-menu (says )
• executes a command...

page 27
Operating Guide
USING THE MENUS
Editing projector settings
If the highlighted menu item is a setting with a list of values to choos\
e from, 
you can change the value in two different ways.
Choosing a value from a list
To access the list of values and then make a selection:
1. Highlight the menu item and press ENTER/SELECT.
2. On the new page that opens, use the UP  and DOWN  arrow buttons 
to highlight a value, then press ENTER/SELECT again. A green “check” 
symbol  marks the current selection....

page 28
Operating Guide
A TOUR OF THE MENUS
A Tour Of  The Menus
The projector settings are grouped into six menus as shown in the illust\
ration.
Main menu
Selecting Main from the top level opens the Main menu.
Notes
 See also Using the Menus earlier 
in this guide and  Menu Map later in 
this guide.
Main Menu
IMAGE
MAIN
ADVANCED IMAGE SYSTEM
CONTROL
SERVICE
Presets
Overscan
3D Control
Input Select
Resync
MAIN >>



Off
HDMI 1
Aspect Ratio
Native
   
    
Digital Projection HIGHlite Cine 330 3D Series...

page 29
Operating Guide
A TOUR OF THE MENUS
Main menu continued from previous page
Aspect Ratio
Choose between 16:9, Theaterscope, 4:3, 4:3 Narrow, 16:10, 5:4 and 
Native.
Notes
Main MenuAspect Ratio
 An anamorphic lens (optional 
accessory) is used with the 
TheaterScope setting, to ensure 
that for a 2.35:1 image, the 
maximum area of the DMD is used, 
giving maximum image brightness.
 The 4:3 Narrow setting is used to 
compensate for the distortion that an 
anamorphic lens would cause to a 
4:3...

page 30
Operating Guide
A TOUR OF THE MENUS
Main menu continued from previous page
Presets
The current image settings can be saved a preset, which you can recall l\
ater. 
The default settings can be recalled at any time as well.
Up to four custom presets can be stored for each  input source you use.
The following settings are saved in a preset:
• From the Main menu — Aspect Ratio and Overscan
• From the Image menu — Brightness, Contrast, Saturation, Hue, 
Sharpness and Noise Reduction
• From the...

page 31
Operating Guide
A TOUR OF THE MENUS
Main menu continued from previous page
Overscan
This setting, if switched on, removes unwanted artefacts from the edges \
of 
your image by cropping the edges or increasing the size of the image to \
force 
the edges off-screen.
Unwanted artefacts along the image edges usually occur when the projecto\
r 
is connected to a low quality input souce.
Choose from Off, Crop or Zoom.
Notes
Main MenuOverscanPresets
Overscan
MAIN >>
Off
3D Control
Input Select Crop...

page 32
Operating Guide
A TOUR OF THE MENUS
3D Control
Use this sub-menu to enable, disable and set up 3D input, as follows:
• 3D Format — Off, Auto, Side by Side (Half), Top and Bottom, 
Dual-Pipe, Frame Sequential.
• 3D Swap — Normal and Reverse (set to Reverse if the 3D images are 
displayed in the wrong order)
• Dark Time — 0.65 ms, 1.3 ms, 1.9 ms and 2.5 ms. Set to reduce the 
effect of images overlapping whilst the glasses are switching
• Sync Delay — set to compensate for signal processsing delays...