Digital Projection Projector E-Vision 8000 User Manual

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_6
...continued from previous page
Notes
ALIGNMENT menu
rear.proj= ?0 = front
1 = rear
ceil.mode= ?0 = floor
1 = ceiling
zoomio+ -+ = Zoom out
- = Zoom in
focus+ -+ = Focus Near
- = Focus Far
vert.offset+ -+ = Up
- = Down
horiz.offset+ -+ = Right
- = Left
Lens.center(execute)
h.keystone= ? + --350~+350
v.keystone= ? + --200~+200
warp.rotat= ? + --20 ~ +20 (in ¼° unit)
warp.pinbrl= ? + --100 ~ +100...

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_7
...continued from previous page
Notes
blank.right= ? + -0 ~ 534
blank.rst(execute)
eb.stat= ?0 = Off
1 = On
eb.wht.top= ? + -0, 200 ~ 5001-199 not allowed
eb.wht.btm= ? + -0, 200 ~ 5001-199 not allowed
eb.wht.left= ? + -0, 200 ~ 8001-199 not allowed
eb.wht.right= ? + -0, 200 ~ 8001-199 not allowed
eb.blk.top= ? + -0, 8, 16, 24, 32
eb.blk.btm= ? + -0, 8, 16, 24, 32
eb.blk.left= ? + -0, 4, 8, 12, 16, 20,...

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_8
...continued from previous page
Notes
net.ipaddr= ?
net.subnet= ?
net.gateway= ?
net.dhcp= ?0 = Off
1 = On
startup.logo= ?0 = Off
1 = On
trig.1= ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
9  = Auto
auto.src= ?0 = Off 
1 = On
lang= ?0 = English
1 = French
2 = Spanish
3 = German
4 = Portuese
5 = Chinese Simplified
6 = Chinese Traditional
7 = Japanese
8 =...

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_9
...continued from previous page
Notes
SERVICE menu
model?
ser.no?
sw.ver?
act.src?0 = HDMI
1 = DVI
2 = RGB D-15
3 = RGBHV/YUV
4 = Composite Video
5 = S-Video
6 = SDI/HDSDI/3G
7 = Option Board
Active Source
pip.src?0 = HDMI
1 = DVI
2 = RGB D-15
3 = RGBHV/YUV
4 = Composite Video
5 = S-Video
6 = SDI/HDSDI/3G
7 = Option Board
pixel.clock?MHz
signal?
h.refresh?KHz
v.refresh?Hz
lamp1.hours?
lamp2.hours?...

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_10
...continued from previous page
Notes
Miscellaneous commands
picture.mute= ?0 = Off
1 = On
power.on(execute)Power on
power.off(execute)Power off (puts projector into Standby mode)
text.mode= ?0 = Off
1 = On
Not available when test pattern is showing
status.check?0 = standby 
1 = warm up 
2 = imaging 
3 = cooling 
4 = warning 
Rev A     April 2012