Digital Projection Projector E-Vision 8000 User Manual

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_13
ALIGNMENT Menu
Rear Projection
• Set this to Off or On as required.
Ceiling Mode
• Set this to Off or On as required.
Lens Control
• Press ENTER to display the Lens Control box.
• Press ENTER again to scroll through the following combinations of lens control and \
background pattern:
• Use , , and to Shift the lens or to adjust the Zoom and Focus, as applicable
Notes
 See also Using the Menus, earlier 
in this guide...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_14
Center Lens
• Press ENTER to Center the Lens.
Lens Memor y sub menu
The current lens position, focus and zoom settings can be saved in one of ten memories, for 
later recall.
• Press ENTER to open the Lens Memory sub menu.
Save Memor y
• Press ENTER to open the Save Memory sub sub menu.
• Use and to select from Lens Memor y 1 to Lens Memor y 10.
• Press ENTER to save the current settings.
Load Memor y
• Press ENTER to...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_15
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 If you are not sure which Warp 
control is in use, then select Reset, 
from the War...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_16
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 If you are not sure which Warp 
control is in use, then select Reset, 
from the War...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_17
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 Black Level Uplift is available for 
up to two edges only, and they 
must be...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_18
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Eco Network Power must be set to 
Standard, if you wish to control the 
projector via the LAN connection.
CONTROL menu
IR Address
• Set this to 1 or 2 as required.
Eco Network Power
• Set this to Standard or Eco as required. In Eco mode, the LAN power supply is switched 
off.
Auto Power Off
• Set this to On, if you want the...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_19
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Eco Network Power must be set to 
Standard, if you wish to control the 
projector via the LAN connection.
 To change any of the network 
settings, use the embedded LAN IP 
Configuration Utility (see later in 
this guide).
Projector Control
• Set this to Network or RS232 as required.
Network sub menu
• Press ENTER to open the...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_20
Startup Logo
• Set this to On if you want the DP logo to show when the projector is first switched on.
Trigger
• Set this to Auto if you want the Trigger output to be activated when the projector is first 
switched on.
• Set this to one of the Aspect Ratio settings, if you want the Trigger output to be 
activated when the projector is switched to that aspect ratio.
Auto Search
• When this is set to On, the projector...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_21
SERVICE menu
Information
• The first part of the menu is for information only.
Blue Only
• Set this to On or Off as required.
Factor y Reset
• Projector will ask for confirmation before restoring all settings to factory defaults.
• When the confirmation box appears, use  or to move the blue highlight to OK 
or Cancel, then press ENTER to confirm your selection.
Notes
 See also Using the Menus, earlier 
in this guide...

Digital Projection E-Vision 8000 series  MENU MAP Operating Guide
Page Op_22
Menu Map
Menu Sub Menus and Controls
INPUT
Input Selection  HDMI, DVI, VGA, Component/BNC, Composite, S-Video, 3G-SDI, Option Board
PIP
PIP Option  Off, On
Main Input  Select from group A or group B
PIP Input  Select from group B or group A
Position  Top Left, Top Right, Bottom Left, Bottom Right, Split L-R
Test Pattern  Off, Colour Bars, Alignment Grid, Vertical Lines, R, G, B, White, Black, Corrected R, G, B, Greyscale
Color...