Digital Projection Projector E-Vision 8000 User Manual

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_5
DVI-D
24 way D-type connector
1 TMDS Data 2-
2 TMDS Data 2+
3 TMDS Data 2 Shield
4 unused
5 unused
6 DDC Clock
7 DDC Data
8 unused
9 TMDS Data 1-
10 TMDS Data 1+
11 TMDS Data 1 Shield
12 unused
13 unused
14 +5 V Power
15 Ground
16 Hot Plug Detect*
17 TMDS Data 0-
18 TMDS Data 0+
19 TMDS Data 0 Shield
20 unused
21 unused
22 TMDS Clock Shield
23 TMDS Clock+
24 TMDS Clock-
* Hot plug detect (HPD) is fully DVI compliant....

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_6
VGA
15 way D-type connector
1 R
2 G
3 B
4 unused 
5 Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5v
10 Digital Ground (V Sync/DDC)
11 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
COMPONENT
5 x 75 ohm BNC
RGBHV  RGsB  YPbPr  YCbCr
Green     Green + Sync  Y    Y
Blue   Blue  Pb  Cb
Red   Red  Pr  Cr
Hsync
Vsync
Notes
 For full details of all input settings, 
see the INPUT menu in the 
Operating Guide.pin view of...

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_7
S-Video input
4 pin mini-DIN
1 Y Ground
2 C Ground
3 Luminance (Y)
4 Chrominance (C)
Video input
1 x RCA Phono
Composite Video
pin view of female connector
Notes
 For full details of all input settings, 
see the INPUT menu in the 
Operating Guide. 
Rev A     April 2012  

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_8
Control connections
LAN connection
TCP Port number 
7000
10BaseT Unshielded Twisted Pair cable
The standard wire colours are as follows:
1 White / Orange stripe
2 Orange
3 White / Green stripe
4 Blue
5 White / Blue stripe
6 Green
7 White / Brown stripe
8 Brown
Crossed cable
(used to connect directly to a computer with no hub or network.) 
(Note that only the green and orange pairs are crossed)
1 White / Orange stripe...

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_9
RS232 Serial control input
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
Null-modem cable
(used to connect the projector to a computer)
RX 2 ---  3 TX
TX 3 ---  2 RX
GND 5 ---  5 GND
Serial port settings
Baud rate 38,400 bps
Data length 8 bits
Stop  bits  one
Parity  none
Flow control none
Wired Remote control connection
3.5mm mini jack
Tip Power
Ring...

E-Vision 8000 Series
High Brightness Digital Video Projector
OPERATING GUIDE
BOOK CONTENTS
OPERATING GUIDE
Using the Remote Control
Test Pattern
Using the Control Panel
Rev A     April 2012  

Digital Projection E-Vision 8000 series  CONTENTS Operating Guide
CONTENTS
Using the Remote Control ...............................................................Op_1
Test Pattern ....................................................................................Op_1
Using the Control Panel ....................................................................Op_2
Using the Menus ........................................................................\
............Op_3
Navigating the menus...

Digital Projection E-Vision 8000 series  CONTENTS Operating Guide
CONTROL menu ...................................................................................Op_18
IR Address....................................................................................Op_18
Eco Network Power......................................................................Op_18
Auto Power Off .............................................................................Op_18
Auto Power On...

Digital Projection E-Vision 8000 series  USING THE REMOTE CONTROL Operating Guide
Page Op_1
Using the Remote ControlNotes
 Some options and controls may not 
be available due to settings in the 
menus.
 For full details of how to use the 
menu system, see later in this guide.
Test Pattern
• Press ENTER to display a Test Pattern.
• Use  or to scroll through the 
following Test Patterns:
... Off, Colour Bars, Alignment Grid, 
Burst, Red, Green, Blue, White, 
Black, Corrected Red, Corrected 
Green,...

Digital Projection E-Vision 8000 series  USING THE CONTROL PANEL Operating Guide
Page Op_2
Notes
 Some options and controls may not 
be available due to settings in the 
menus.
 For full details of how to use the 
menu system, see later in this guide.
Using the Control Panel
MENU controlsLENS controls
POWER: Off or Standby
INPUT: select from the available video input signals
AUTO SYNC: Projector will re-synchronise with the current input signal
ASPECT: select from a list of available aspect...