Digital Projection Projector E-Vision 8000 User Manual
Have a look at the manual Digital Projection Projector E-Vision 8000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 20
Digital Projection E-Vision 8000 series WIRING DETAILS Connection Guide
Page Conn_4
Wiring Details
Signal inputs and outputs
3G-SDI
75 ohm BNC
SMPTE 292 / HD-SDI signals are very high speed digital signals which req\
uire better quality
coaxial cable than conventional analogue video. The data rate is 1.5 Gigabits per second.
In choosing cable length and connectors for any installation the frequen\
cy response loss
in decibels should be proportional to √f, from 1MHz, to 1.5GHz. The following or...](http://img.usermanuals.tech/thumb/5761/99274/w64_projector_manual_7009_d-19.png "Page 20
Digital Projection E-Vision 8000 series WIRING DETAILS Connection Guide
Page Conn_4
Wiring Details
Signal inputs and outputs
3G-SDI
75 ohm BNC
SMPTE 292 / HD-SDI signals are very high speed digital signals which req\
uire better quality
coaxial cable than conventional analogue video. The data rate is 1.5 Gigabits per second.
In choosing cable length and connectors for any installation the frequen\
cy response loss
in decibels should be proportional to √f, from 1MHz, to 1.5GHz. The following or...")
Digital Projection E-Vision 8000 series WIRING DETAILS Connection Guide Page Conn_5 DVI-D 24 way D-type connector 1 TMDS Data 2- 2 TMDS Data 2+ 3 TMDS Data 2 Shield 4 unused 5 unused 6 DDC Clock 7 DDC Data 8 unused 9 TMDS Data 1- 10 TMDS Data 1+ 11 TMDS Data 1 Shield 12 unused 13 unused 14 +5 V Power 15 Ground 16 Hot Plug Detect* 17 TMDS Data 0- 18 TMDS Data 0+ 19 TMDS Data 0 Shield 20 unused 21 unused 22 TMDS Clock Shield 23 TMDS Clock+ 24 TMDS Clock- * Hot plug detect (HPD) is fully DVI compliant. DVI sources detect the presence of a display device by providing +5V on pin 14 and looking for +5V on pin 16. Wheneve\ r the projector is operational, and 5V is present on pin 14, pin 16 will be held at +5V. EDID is available even when the projector is switched off. Operational means that the projector is powered up. Non operational sta\ tes are powered down and some self test and reprogramming modes. High Definition Content Protection (HDCP) is supported on this input. Notes For full details of all input settings, see the INPUT menu in the Operating Guide.pin view of female connector Rev A April 2012
Digital Projection E-Vision 8000 series WIRING DETAILS Connection Guide Page Conn_6 VGA 15 way D-type connector 1 R 2 G 3 B 4 unused 5 Digital Ground (H Sync) 6 R Ground 7 B Ground 8 G Ground 9 +5v 10 Digital Ground (V Sync/DDC) 11 unused 12 SDA 13 H Sync 14 V Sync 15 SCL COMPONENT 5 x 75 ohm BNC RGBHV RGsB YPbPr YCbCr Green Green + Sync Y Y Blue Blue Pb Cb Red Red Pr Cr Hsync Vsync Notes For full details of all input settings, see the INPUT menu in the Operating Guide.pin view of female connector Pb/Cb Y Pr/Cr Blue Green Red V H Rev A April 2012
Digital Projection E-Vision 8000 series WIRING DETAILS Connection Guide Page Conn_7 S-Video input 4 pin mini-DIN 1 Y Ground 2 C Ground 3 Luminance (Y) 4 Chrominance (C) Video input 1 x RCA Phono Composite Video pin view of female connector Notes For full details of all input settings, see the INPUT menu in the Operating Guide. Rev A April 2012
Digital Projection E-Vision 8000 series WIRING DETAILS Connection Guide Page Conn_8 Control connections LAN connection TCP Port number 7000 10BaseT Unshielded Twisted Pair cable The standard wire colours are as follows: 1 White / Orange stripe 2 Orange 3 White / Green stripe 4 Blue 5 White / Blue stripe 6 Green 7 White / Brown stripe 8 Brown Crossed cable (used to connect directly to a computer with no hub or network.) (Note that only the green and orange pairs are crossed) 1 White / Orange stripe White / Green stripe 1 2 Orange Green 2 3 White / Green stripe White / Orange stripe 3 4 Blue Blue 4 5 White / Blue stripe White / Blue stripe 5 6 Green Orange 6 7 White / Brown stripe White / Brown stripe 7 8 Brown Brown 8 Notes For full details of all control settings, see the CONTROL menu in the Operating Guide. Use: a straight cable to connect to a hub or network, or a crossed cable as shown here to connect ONLY to a computer directly. top view of cable connector (clip is underneath) Rev A April 2012
Digital Projection E-Vision 8000 series WIRING DETAILS Connection Guide Page Conn_9 RS232 Serial control input 1 unused 2 Received Data (RX) 3 Transmitted Data (TX) 4 unused 5 Signal Ground 6 unused 7 unused 8 unused 9 unused Null-modem cable (used to connect the projector to a computer) RX 2 --- 3 TX TX 3 --- 2 RX GND 5 --- 5 GND Serial port settings Baud rate 38,400 bps Data length 8 bits Stop bits one Parity none Flow control none Wired Remote control connection 3.5mm mini jack Tip Power Ring Signal Sleeve Ground Screen Trigger output 3.5mm mini jack Tip Signal Sleeve Ground Notes For full details of all control settings, see the CONTROL menu in the Operating Guide. The projector is a DTE, so use: a straight cable to connect to a modem, or a null-modem cable as shown here to connect to another DTE such as a computer. Note that plugging in the remote control cable will disable the infra- red. pin view of female connector SleeveTip Sleeve Ring Tip Rev A April 2012
E-Vision 8000 Series High Brightness Digital Video Projector OPERATING GUIDE BOOK CONTENTS OPERATING GUIDE Using the Remote Control Test Pattern Using the Control Panel Rev A April 2012
Digital Projection E-Vision 8000 series CONTENTS Operating Guide CONTENTS Using the Remote Control ...............................................................Op_1 Test Pattern ....................................................................................Op_1 Using the Control Panel ....................................................................Op_2 Using the Menus ........................................................................\ ............Op_3 Navigating the menus ............................................................................Op_3 Sub Menus ..............................................................................................Op_4 Selecting parameters .............................................................................Op_5 Sliders .....................................................................................................Op_6 Commands ..............................................................................................Op_6 A Tour of the Menus ........................................................................\ ....Op_7 INPUT Menu ............................................................................................Op_7 Input Selection ...............................................................................Op_7 PIP (Picture in Picture) sub menu ..................................................Op_7 Test Pattern ....................................................................................Op_8 Color Space ...................................................................................Op_8 Input Lock.......................................................................................Op_8 Background ....................................................................................Op_8 Video Standard ..............................................................................Op_8 Auto Sync Adjust ............................................................................Op_8 PICTURE Menu .......................................................................................Op_9 Display Mode .................................................................................Op_9 Contrast, Brightness, Saturation, Hue............................................Op_9 Dynamic Contrast...........................................................................Op_9 Gamma ..........................................................................................Op_9 Color sub menu ............................................................................Op_10 Sharpness, Noise Reduction........................................................Op_10 Aspect Ratio .................................................................................Op_10 Overscan ......................................................................................Op_11 VGA Setup sub menu...................................................................Op_11 Auto Sync .....................................................................................Op_11 LAMPS Menu ........................................................................................Op_12 Mode ............................................................................................Op_12 Power ...........................................................................................Op_12 High Altitude Mode .......................................................................Op_12 Custom Power..............................................................................Op_12 Lamp Status and Time .................................................................Op_12 ALIGNMENT Menu ................................................................................Op_13 Rear Projection ............................................................................Op_13 Ceiling Mode ................................................................................Op_13 Lens Control .................................................................................Op_13 Center Lens..................................................................................Op_14 Lens Memory sub menu...............................................................Op_14 Warp sub menu ............................................................................Op_15 Blanking sub menu.......................................................................Op_16 Edge Blend sub menu ..................................................................Op_17 continued Rev A April 2012
Digital Projection E-Vision 8000 series CONTENTS Operating Guide CONTROL menu ...................................................................................Op_18 IR Address....................................................................................Op_18 Eco Network Power......................................................................Op_18 Auto Power Off .............................................................................Op_18 Auto Power On .............................................................................Op_18 Projector Control ..........................................................................Op_19 Network sub menu .......................................................................Op_19 Startup Logo.................................................................................Op_20 Trigger ..........................................................................................Op_20 Auto Search .................................................................................Op_20 Dynamic Black .............................................................................Op_20 Language .....................................................................................Op_20 SERVICE menu .....................................................................................Op_21 Information ...................................................................................Op_21 Blue Only......................................................................................Op_21 Factory Reset ...............................................................................Op_21 Menu Map ........................................................................\ .........................Op_22 INPUT.....................................................................................................Op_22 PICTURE................................................................................................Op_22 LAMPS ...................................................................................................Op_23 ALIGNMENT .........................................................................................Op_23 CONTROL ..............................................................................................Op_24 SERVICE ................................................................................................Op_24 LAN IP Configuration Utility.........................................................Op_25 Rev A April 2012
Digital Projection E-Vision 8000 series USING THE REMOTE CONTROL Operating Guide Page Op_1 Using the Remote ControlNotes Some options and controls may not be available due to settings in the menus. For full details of how to use the menu system, see later in this guide. Test Pattern • Press ENTER to display a Test Pattern. • Use or to scroll through the following Test Patterns: ... Off, Colour Bars, Alignment Grid, Burst, Red, Green, Blue, White, Black, Corrected Red, Corrected Green, Corrected Blue, Greyscale, Off ... • To return to viewing the image from your image source, use or to scroll through the list to Off. To protect the lamps from thermal shock, it will not be possible to change the Lamp Mode more than once within five minutes. MENU controls LENS controls POWER controls INPUT: select from the available video input signals PICTURE: opens the Picture menu AUTO SYNC: Projector will re-synchronise with the current input signal ASPECT: select from a list of available aspect ratios OVERSCAN: select from Off Crop or Zoom FREEZE: freeze the current image frame 3D MODE: has no function on this projector INFO: opens the Service menu NETWORK: has no function on this projector LAMP MODE: has no function on this projectorl LIGHT: illuminates the buttons on the remote control for 10 seconds TEST PATTERN: select from a list of available test patterns PIP: switches the PIP image on or off ID SET: has no function on this projector CLEAR: has no function on this projector SHUTTER: opens or closes the shutter Rev A April 2012
Digital Projection E-Vision 8000 series USING THE CONTROL PANEL Operating Guide Page Op_2 Notes Some options and controls may not be available due to settings in the menus. For full details of how to use the menu system, see later in this guide. Using the Control Panel MENU controlsLENS controls POWER: Off or Standby INPUT: select from the available video input signals AUTO SYNC: Projector will re-synchronise with the current input signal ASPECT: select from a list of available aspect ratiosSHUTTER: open or close the shutter Rev A April 2012