Digital Projection Projector E-Vision 8000 User Manual

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_13
ALIGNMENT Menu
Rear Projection
• Set this to Off or On as required.
Ceiling Mode
• Set this to Off or On as required.
Lens Control
• Press ENTER to display the Lens Control box.
• Press ENTER again to scroll through the following combinations of lens control and \
background pattern:
• Use , , and to Shift the lens or to adjust the Zoom and Focus, as applicable
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Shift with  
no pattern
Zoom/Focus with 
grid and crosses
Shift with  
grid
Zoom/Focus with 
crosses 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_14
Center Lens
• Press ENTER to Center the Lens.
Lens Memor y sub menu
The current lens position, focus and zoom settings can be saved in one of ten memories, for 
later recall.
• Press ENTER to open the Lens Memory sub menu.
Save Memor y
• Press ENTER to open the Save Memory sub sub menu.
• Use and to select from Lens Memor y 1 to Lens Memor y 10.
• Press ENTER to save the current settings.
Load Memor y
• Press ENTER to open the Load Memory sub sub menu.
• Use and to select from Lens Memor y 1 to Lens Memor y 10.
• Press ENTER to recall the saved settings.
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
ALIGNMENT Menu continued 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_15
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 If you are not sure which Warp 
control is in use, then select Reset, 
from the War p menu to reset all 
controls to zero.
Warp sub menu
• Press ENTER to open the Warp sub menu.
Keystone, Rotation, Pincushion/Barrel, Corner
• Use and to select one of the warp controls.
• Press ENTER to open the warp control box:
• Use the Keystone control to correct for any distortion caused by the projector being 
in a different horizontal or vertical plane to the screen..
• Use the Rotation control to rotate the image up to 5° clockwise or anti-clockwise.
• Use the Pincushion/Barrel control to correct for any distortion caused by the screen 
being concave or convex.
• Use the four Corner controls to stretch the image from each of the four corners..
• Use Custom Warp to activate a user-defined warp pattern.
Reset
• Press ENTER to reset all warp settings to zero.
Warp control boxes
ALIGNMENT Menu continued 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_16
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 If you are not sure which Warp 
control is in use, then select Reset, 
from the War p menu to reset all 
controls to zero.
Blanking sub menu
• Press ENTER to open the Blanking sub menu.
Top, Bottom, Left and Right
• Set each slider as required.
Reset
• Press ENTER to reset all blanking settings to zero.
ALIGNMENT Menu continued 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_17
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 Black Level Uplift is available for 
up to two edges only, and they 
must be top+bottom, or left+right 
– not top+left for example.
 Therefore, uplift can only be used 
for an array of projectors either:
 1 projector high or 
1 projector wide
Edge Blend sub menu
When several projectors are used to create a large tiled image, the edge\
s need to be blended to avoid the 
overlaps appearing brighter than the rest of the image..
•  Press ENTER to open the Edge Blend sub menu.
Edge Blend
• Set this to Off or On as required.
Blend Width
• Press ENTER to open the Blend Width sub sub menu.
• Set the Width sliders to the blend width required for each edge to be blended.
Black Level Uplift
• Press ENTER to open the Black Level Uplift sub sub menu.
• Set the Area sliders to correct for stray light from the DMD’s non-addressable border.
• Set the All sliders for the amount of uplift required; the Colour sliders can be used for fine adjustment.
Reset
• Press ENTER to reset all edge blend settings to zero.
Align Pattern
• Set this to Off or On as required.
ALIGNMENT Menu continued
Blend 
width 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_18
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Eco Network Power must be set to 
Standard, if you wish to control the 
projector via the LAN connection.
CONTROL menu
IR Address
• Set this to 1 or 2 as required.
Eco Network Power
• Set this to Standard or Eco as required. In Eco mode, the LAN power supply is switched 
off.
Auto Power Off
• Set this to On, if you want the projector to go into Standby mode when no input source 
is detected for 20 minutes.
Auto Power On
• Set this to On, if you want the projector to start up immediately when the mains is 
connected.
• Set this to Off, if you want the projector to go into Standby mode when the mains is 
connected. In this case, the projector will not start up until the POWER button is pressed 
on the control panel or the remote control. 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_19
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Eco Network Power must be set to 
Standard, if you wish to control the 
projector via the LAN connection.
 To change any of the network 
settings, use the embedded LAN IP 
Configuration Utility (see later in 
this guide).
Projector Control
• Set this to Network or RS232 as required.
Network sub menu
• Press ENTER to open the Network sub sub menu.
The settings here are for information only.
CONTROL Menu continued 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_20
Startup Logo
• Set this to On if you want the DP logo to show when the projector is first switched on.
Trigger
• Set this to Auto if you want the Trigger output to be activated when the projector is first 
switched on.
• Set this to one of the Aspect Ratio settings, if you want the Trigger output to be 
activated when the projector is switched to that aspect ratio.
Auto Search
• When this is set to On, the projector will search for an alternative input source when the 
current input source is disconnected
• When this is set to Off, the projector will show the DP logo when the current input source 
is disconnected.
Dynamic Black
• Set this to On or Off as required.
Language
• Press ENTER to open the Language Selection menu, then select an language from the 
list.
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Dynamic Black reduces the overall 
light output for images that contain 
a lot of black. This improves the 
perceived contrast ratio.
CONTROL Menu continued 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_21
SERVICE menu
Information
• The first part of the menu is for information only.
Blue Only
• Set this to On or Off as required.
Factor y Reset
• Projector will ask for confirmation before restoring all settings to factory defaults.
• When the confirmation box appears, use  or to move the blue highlight to OK 
or Cancel, then press ENTER to confirm your selection.
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Do NOT do this unless you are 
sure that you want to restore ALL 
settings to their factory defaults. 
Rev A     April 2012  
						

							Digital Projection E-Vision 8000 series  MENU MAP Operating Guide
Page Op_22
Menu Map
Menu Sub Menus and Controls
INPUT
Input Selection  HDMI, DVI, VGA, Component/BNC, Composite, S-Video, 3G-SDI, Option Board
PIP
PIP Option  Off, On
Main Input  Select from group A or group B
PIP Input  Select from group B or group A
Position  Top Left, Top Right, Bottom Left, Bottom Right, Split L-R
Test Pattern  Off, Colour Bars, Alignment Grid, Vertical Lines, R, G, B, White, Black, Corrected R, G, B, Greyscale
Color Space   Auto, YCbCr, YPbPr, RGB-PC, RGB-Video
Input Lock  Auto, 48Hz, 50Hz, 60Hz
Background  Logo, Blue, Black, White
Video Standard  Auto, PAL, SECAM, NTSC
Auto Sync Adjust  Always, Off, Auto
PICTURE
Display Mode  Video, High Bright, Presentation
Contrast
Dynamic Contrast  Off, On
Brightness
Saturation
Hue
Gamma  Video, Linear, Film, Graphics
Color
Color Temperature  Native, 5000K-9300K
Trim  RGB Lift and Gain
Sharpness
Noise Reduction
Aspect Ratio  5:4, 4:3, 16:10, 16:9, 1.88, 2.35, Letterbox, Native, Unscaled
Overscan Off, Crop, Zoom
VGA Setup  H Total, H Start, H Phase, V Start
Auto Sync  Press ENTER to execute
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide. 
Rev A     April 2012