Digital Projection Projector E-Vision 8000 User Manual

Digital Projection E-Vision 8000 series  POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Page Inst_7
Notes
 Always allow the lamp to cool for 
5 minutes before:
  - disconnecting the power 
- moving the projector
 Ensure that there is at least 
70cm (28in) of space between 
the ventilation outlets and any 
wall, and 50cm (20in) on all other 
sides.
  If ceiling mounting, ensure there 
is 30cm (12in) of space between 
the projector and ceiling.
 Backup safety chains or wires...

Digital Projection E-Vision 8000 series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
Page Inst_8
Operating the Projector
Switching the Projector On
• Connect the power cable between the mains supply and the projector . Switch on at the switch next to the power connector.
• Wait until the self-test has completed and the Power indicator on the projector control panel shows red. The lamp will be off and the 
projector will be in STANDBY mode.
• Press POWER  on the control panel or POWER ON on...

Digital Projection E-Vision 8000 series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
Page Inst_9
Adjusting the Lens
Zoom
• Use the ZOOM +/− buttons on the control panel or on the remote control to adjust the 
lens so that the image fills the screen.
or use Lens Control in the ALIGNMENT Menu.
Focus
• Use the FOCUS +/− buttons on the control panel or on the remote control to adjust the 
lens until the image is sharp.
or use Lens Control in the ALIGNMENT Menu.
Shift
• Use the LENS SHIFT...

Digital Projection E-Vision 8000 series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
Page Inst_10
Switching the Projector Off
• Press and hold POWER  on the control panel or POWER OFF on the remote control for 5 seconds.
The lamp will go off, and the Power indicator on the control panel will flash amber for a few seconds whilst the lamp cools.  The Power 
indicator on the control panel will then show red and the projector will\
 be in Standby mode.
• Switch off at the switch next to the...

E-Vision 8000 Series
High Brightness Digital Video Projector
CONNECTION GUIDE
BOOK CONTENTS
CONNECTION GUIDE
Signal Inputs and Outputs
3G-SDI IN
3G-SDI OUT
Rev A     April 2012  

Digital Projection E-Vision 8000 series  CONTENTS Connection Guide
CONTENTS
Signal Inputs and Outputs ..........................................................Conn_1
3G-SDI IN .............................................................................................Conn_1
3G-SDI OUT .........................................................................................Conn_1
HDMI ....................................................................................................Conn_1...

Digital Projection E-Vision 8000 series  SIGNAL INPUTS AND OUTPUTS Connection Guide
Page Conn_1
Signal Inputs and Outputs
3G-SDI IN
• Connect a 3G-SDI cable to the left hand SDI BNC.
3G-SDI OUT
• Connect a 3G-SDI cable to the right hand SDI BNC, to distribute the signal to another 
projector.
HDMI
• Connect a HDMI cable to the HDMI connector.
DVI-D
• Connect a DVI-D cable to the DVI connector.
VGA
• If necessary, use the VGA Setup controls in the PICTURE menu. For more information, 
see the Operating...

Digital Projection E-Vision 8000 series  SUPPORTED SIGNAL INPUT MODES Connection Guide
Page Conn_2
Supported Signal Input Modes
SignalResolutionRefresh Rate ( Hz )
Total number of lines
Horizontal  Frequency (kHz)
VIDEOS-VIDEOCOMPONENT
VGADVI/HDMISDI
SDTV480i720 x 48059.9452515.73üüüü
576i720 x 5765062515.63üüüü
HDTV 480p720 x 48059.9452531.47üü
576p720 x 5765062531.25üü
720p501280 x 7205075037.50üüü
720p601280 x 7206075045.00üüü
1080p241920 x 108024112527.00üüü
1080i501920 x 108050112528.13üü...

Digital Projection E-Vision 8000 series  CONTROL CONNECTIONS Connection Guide
Page Conn_3
Control Connections
LAN
• All of the projector’s features can be controlled via a LAN connection, using the control 
strings described in the Remote Communications Guide..
• The LAN IP Address of the projector can be set by using the LAN IP Configuration 
Utility. To see what the Address is set to, you can view the current Network settings in 
the CONTROL Menu.
 For more information about these settings, see the...

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_4
Wiring Details
Signal inputs and outputs
3G-SDI
75 ohm BNC
SMPTE 292 / HD-SDI signals are very high speed digital signals which req\
uire better quality 
coaxial cable than conventional analogue video. The data rate is 1.5 Gigabits per second.
In choosing cable length and connectors for any installation the frequen\
cy response loss 
in decibels should be proportional to √f, from 1MHz, to 1.5GHz.  The following or...