Digital Projection Projector E-Vision 8000 User Manual

Digital Projection E-Vision 8000 series  USING THE MENUS Operating Guide
Page Op_3
Using the Menus
Use the buttons on the projector control 
panel or on the remote control, to access the 
menu system.
• To open the on-screen display (OSD), 
press MENU. To close, press EXIT/
RETURN.
Notes
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
Remote controlProjector control panel
Navigating the menus
• Select a menu using...

Digital Projection E-Vision 8000 series  USING THE MENUS Operating Guide
Page Op_4
Notes
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
 The Sub Menu appears to either 
the left or right side of the menu it 
was called from, depending on the 
space available.
 The Sub Submenu appears in place 
of the sub menu it was called from.
Sub Menus
• Select a sub menu using
 and.
• then open the Sub Menu by pressing 
ENTER.
The...

Digital Projection E-Vision 8000 series  USING THE MENUS Operating Guide
Page Op_5
Selecting parameters
Most parameters are changed by selecting 
from a list:
• Select from the list using
 and .
• The change will usually be made 
immediately.
Notes
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
 There may be a short delay when 
changing some parameters, due to 
internal processing time.
 The sub menu appears to the...

Digital Projection E-Vision 8000 series  USING THE MENUS Operating Guide
Page Op_6
Sliders
• Use  or to adjust the value.
The menu will disappear, to be replaced 
by a slider bar.
• To return to the menu, press MENU.
Notes
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
Commands
• To execute the command, press 
ENTER.
In this example,
• use  or to move the blue 
highlight to OK or Cancel,
• then press ENTER to confirm...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_7
A Tour of  the Menus
INPUT Menu
Input Selection
• Press ENTER to open the Input Selection menu, then select an input from the list.
PIP (Picture in Picture) sub menu
• Press ENTER to open the PIP sub menu.
PIP Option
• Set PIP Option to On or Off.
Main and PIP Inputs
• Select a Main Input from the drop-down list. The inputs are divided into 
two groups – the main image must be from one group, and the sub-
image must be...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_8
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Test Pattern
• Press ENTER to display a Test Pattern.
• Use  or to scroll through the following Test Patterns:
... Off, Colour Bars, Alignment Grid, Burst, Red, Green, Blue, White, Black, Corrected Red, 
Corrected Green, Corrected Blue, Greyscale, Off  ...
• To return to viewing the image from your image source, use  or to...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_9
PICTURE Menu
Display Mode
• Select one of the Display modes as required.
Contrast, Brightness, Saturation, Hue
• Adjust the sliders for these settings, as required.
Dynamic Contrast
• Set this to On or Off as required.
Gamma
• Select one of the Gamma settings as required.
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide. 
Rev A     April 2012  

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_10
Color sub menu
• Press ENTER to open the Color sub menu.
Colour Temperature
• Set this to suit the specification of the input source, or to improve the appearance of the 
projected image.
Trim
• Set the Red, Green and Blue Lift and Gain settings, to improve the appearance of the 
projected image.
Sharpness, Noise Reduction
• Adjust the sliders for these settings, as required.
Aspect Ratio
• Set Aspect Ratio to suit...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_11
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Overscan is used to compensate 
for	noisy	or	badly	defined	image	
edges, by cropping the image, or  
increasing the size of the image to 
force the edges off-screen.
Overscan
• Set this to Off On or Zoom as required.
VGA Setup sub menu
• Press ENTER to open the VGA Setup sub menu.
 Horizontal Total, Start and Phase, Vertical...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_12
LAMPS Menu
Mode
• Set this to Single or Dual as required.
When	the	mode	is	changed,	it	will	not	be	possible	to	change	it	again	within	five	minutes.
Power
• Set this to Normal for 100% power, Eco for 80% power or Custom to enable the 
Custom Power slider.
High Altitude Mode
• Set this to On if it is necessary to have the cooling fans running at high speed.
Custom Power
• Set the slider as required.
Lamp Status and...