Digital Projection Projector E-Vision 8000 Series User Manual

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
35
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Test Pattern
• Press ENTER to display a Test Pattern.
• Use  or to scroll through the following Test Patterns:
... Off, Color Bars, Alignment Grid, Burst, Red, Green, Blue, White, Black, Cross Mark, Cross 
Hatch + Mark, Corrected Red, Corrected Green, Corrected Blue, Horizontal Ramp, Off  ...
• To return to viewing the image from your...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
36
PICTURE menu
Display Mode
• Select one of the Display modes as required.
Contrast, Brightness, Saturation, Hue
• Adjust the sliders for these settings, as required.
Adaptive Contrast
• Set this to On or Off as required.
Gamma
• Select one of the Gamma settings as required.
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
INPUTPICTURELAMPSALIGNMENTCONTROLSERVICEDisplay Mode Contrast...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
37
Color submenu
• Press ENTER to open the Color submenu.
Color Temperature
• Set this to suit the specification of the input source, or to improve the appearance of the 
projected image.
Trim
• Set the Red, Green and Blue Lift and Gain settings, to improve the appearance of the 
projected image.
Sharpness, Noise Reduction
• Adjust the sliders for these settings, as required.
Aspect Ratio
• Set Aspect Ratio to suit the incoming...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
38
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Overscan is used to compensate 
for noisy or badly defined image 
edges, by cropping the image, or  
increasing the size of the image to 
force the edges off-screen.
Overscan
• Set this to Off On or Zoom as required.
VGA Setup submenu
• Press ENTER to open the VGA Setup submenu.
 Horizontal Total, Start and Phase, Vertical Start
•...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
39
LAMPS menu
Mode
• Set this to Single or Dual as required.
When the mode is changed, it will not be possible to change it again within five minutes.
Power
• Set this to Normal for 100% power, Eco for 80% power or Custom to enable the 
Custom Power slider.
High Altitude Mode
• Set this to On if it is necessary to have the cooling fans running at high speed.
Custom Power Level
• Set the slider as required.
Lamp Status
• For...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
40
ALIGNMENT menu
Projection Mode
• Front and Rear define whether the projector is in front of the screen or behind it. 
Set to Ceiling + Front or Ceiling + Rear if the projector is ceiling mounted.
Fan Mode
• Adjusts the fan speeds to optimise cooling when the projector is in vert\
ical orientation. 
Set to Up or Down as appropriate when projecting lens up or down.
Lens Control
• Press ENTER to display the Lens Control box.
•...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
41
Lens Memor y submenu
The current lens position, focus and zoom settings can be saved in one o\
f ten memories, for 
later recall.
• Press ENTER to open the Lens Memory submenu.
Save Memor y
• Press ENTER to open the Save Memory submenu.
• Use and to select from Lens Memor y 1 to Lens Memor y 10.
• Press ENTER to save the current settings.
Load Memor y
• Press ENTER to open the Load Memory submenu.
• Use and to select from...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
42
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 If you are not sure which Warp 
control is in use, then select Reset, 
from the War p menu...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
43
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 If you are not sure which Warp 
control is in use, then select Reset, 
from the War p menu...

Digital Projection E-Vision 8000 Series  A TOUR OF THE MENUS Operating Guide
44
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 Black Level Uplift is available for 
up to two edges only, and they 
must be top+bottom, or...