Digital Projection Projector E-Vision 8000 Series User Manual

Digital Projection E-Vision 8000 Series  GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
5
Control panel
Some of the controls from the remote control are duplicated on the proje\
ctor control panel, as 
shown below.
The EXIT button has the same function as the RETURN button on the remote control.
Notes
 For full details of how to use the 
controls and the menu system, see 
the Operating Guide.
Indicators
SHUTTER off = OPEN green = CLOSED
TEMP off = NO ERROR  flashing red = ERROR...

Digital Projection E-Vision 8000 Series  CHANGING THE LENS, LAMPS, FILTERS AND COLOR WHEEL Installation and Quick-Start Guide
6
Changing The Lens, Lamps, Filters And Color Wheel
Removing the lens
• Push in the lens release lever, and turn the lens anti-clockwise.
• Remove the lens.
Fitting the lens
• Remove the lens cap.
• Position the lens so that the labels are at the top, and gently insert i\
t all the way into the 
lens mount.
• Push the lens in firmly, and turn it clockwise until it clicks into...

Digital Projection E-Vision 8000 Series  CHANGING THE LENS, LAMPS, FILTERS AND COLOR WHEEL Installation and Quick-Start Guide
7
Changing a lamp
• Unscrew the two captive screws securing the cover for the lamp that need\
s changing.
• Open the lamp compartment.
• Unscrew the three captive screws securing the lamp module.
• Pull firmly on the handle to remove the lamp module.
• Insert a new lamp module and fasten the screws.
• Replace the lamp compartment cover and fasten the screws.
Notes
 Always allow...

Digital Projection E-Vision 8000 Series  CHANGING THE LENS, LAMPS, FILTERS AND COLOR WHEEL Installation and Quick-Start Guide
8
Changing the color wheel
• Unscrew the captive screw securing the 
color wheel compartment cover.
• Open the color wheel compartment.
• Unscrew the four captive screws securing 
the color wheel.
• Remove the color wheel.
• Insert a new color wheel and fasten the 
screws.
• Replace the cover and fasten the screw.
Cover 
screw
Color wheel 
compartment
Color 
wheel 
screws
Notes...

Digital Projection E-Vision 8000 Series  POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
9
Notes
 Always allow the lamp to cool for 
5 minutes before:
  - disconnecting the power 
- moving the projector
 Ensure that there is at least 
70cm (28in) of space between 
the ventilation outlets and any 
wall, and 50cm (20in) on all other 
sides.
  If ceiling mounting, ensure there 
is 30cm (12in) of space between 
the projector and ceiling.
 Backup safety chains or wires 
should always...

Digital Projection E-Vision 8000 Series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
10
Operating The Projector
Switching the projector on
• Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
• Wait until the self-test has completed and the Power indicator on the projector control panel shows red. The lamp will be off and the 
projector will be in STANDBY mode.
• Press POWER  on the control panel or POWER ON on the...

Digital Projection E-Vision 8000 Series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
11
Adjusting the lens
Zoom
• Use the ZOOM +/− buttons on the control panel or on the remote control to adjust the 
lens so that the image fills the screen.
or use Lens Control in the ALIGNMENT Menu.
Focus
• Use the FOCUS +/− buttons on the control panel or on the remote control to adjust the 
lens until the image is sharp.
or use Lens Control in the ALIGNMENT Menu.
Shift
• Use the LENS SHIFT buttons , ,...

Digital Projection E-Vision 8000 Series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
12
Switching the projector off
• Press and hold POWER  on the control panel or POWER OFF on the remote control for 5 seconds.
The lamp will go off, and the Power indicator on the control panel will flash amber for a few seconds whilst the lamp cools.  The Power 
indicator on the control panel will then show red and the projector will\
 be in Standby mode.
• Switch off at the switch next to the power...

E-Vision 8000 Series
High Brightness Digital Video Projector
CONNECTION GUIDE
Rev F July 2014  

Digital Projection E-Vision 8000 Series  IN THIS GUIDE Connection Guide
IN THIS GUIDE
Signal Inputs And Outputs ....................................................................Conn_1
3G-SDI IN .........................................................................................................Conn_1
3G-SDI OUT .....................................................................................................Conn_1
HDMI...