Digital Projection Projector E-Vision 8000 Series User Manual

Digital Projection E-Vision 8000 Series  SIGNAL INPUTS AND OUTPUTS Connection Guide
15
Signal Inputs And Outputs
3G-SDI IN
• Connect a 3G-SDI cable to the left hand SDI BNC.
3G-SDI OUT
• Connect a 3G-SDI cable to the right hand SDI BNC, to distribute the signal to another 
projector.
HDMI
• Connect a HDMI cable to the HDMI connector.
DVI-D
• Connect a DVI-D cable to the DVI connector.
VGA
• If necessary, use the VGA Setup controls in the PICTURE menu. For more information, 
see the Operating Guide.
• Set...

Digital Projection E-Vision 8000 Series  SUPPORTED SIGNAL INPUT MODES Connection Guide
16
Supported Signal Input Modes
StandardResolutionRefresh Rate ( Hz )
Total number of lines
Horizontal  Frequency (kHz)
VIDEOS-VIDEOCOMPONENTDVI-A / VGADVI -D / HDMI
3G-SDI
SDTV480i720 x 4806052515.73üüüü
576i720 x 5765062515.63üüüü
EDTV480p720 x 4806052531.51üü
576p720 x 5765062531.25üü
HDTV720p501280 x 7205075037.51üü
720p601280 x 7206075045.00üüü
1035i601920 x 108035112533.75üüü
1080sf251920 x 108025112528.13üüü...

Digital Projection E-Vision 8000 Series  SUPPORTED SIGNAL INPUT MODES Connection Guide
17
...continued from previous page
StandardResolutionRefresh Rate ( Hz )
Total number of lines
Horizontal  Frequency (kHz)
VIDEOS-VIDEOCOMPONENTDVI-A / VGADVI-D / HDMI3G-SDI
SXGA601280 x 102460106663.98üü
SXGA+601400 x 105060108965.32üü
UXGA601600 x 120060124575.00üü
VESA1080p1920 x 108060112067.50üü
WUXGA601920 x 120060123574.04üü
Notes 
Rev F July 2014  

Digital Projection E-Vision 8000 Series  CONTROL CONNECTIONS Connection Guide
18
Control Connections
LAN
• The projector’s features can be controlled via a LAN connection, using the control str\
ings 
described in the Remote Communications Guide..
• The LAN IP Address of the projector can be set by using the Web Configuration Utility. 
To see what the Address is set to, you can view the current Network settings in the 
CONTROL Menu.
 For more information about these settings, see the Operating Guide....

Digital Projection E-Vision 8000 Series  WIRING DETAILS Connection Guide
19
Wiring Details
Signal inputs and outputs
3G-SDI
75 ohm BNC
SMPTE 292 / HD-SDI signals are very high speed digital signals which req\
uire better quality 
coaxial cable than conventional analogue video. The data rate is 1.5 Gigabits per second.
In choosing cable length and connectors for any installation the frequen\
cy response loss 
in decibels should be proportional to √f, from 1MHz, to 1.5GHz.  The following or similar 
cable...

Digital Projection E-Vision 8000 Series  WIRING DETAILS Connection Guide
20
DVI-D
24 way D-type connector
1 TMDS Data 2-
2 TMDS Data 2+
3 TMDS Data 2 Shield
4 unused
5 unused
6 DDC Clock
7 DDC Data
8 unused
9 TMDS Data 1-
10 TMDS Data 1+
11 TMDS Data 1 Shield
12 unused
13 unused
14 +5 V Power
15 Ground
16 Hot Plug Detect*
17 TMDS Data 0-
18 TMDS Data 0+
19 TMDS Data 0 Shield
20 unused
21 unused
22 TMDS Clock Shield
23 TMDS Clock+
24 TMDS Clock-
* Hot plug detect (HPD) is fully DVI compliant.  DVI sources...

Digital Projection E-Vision 8000 Series  WIRING DETAILS Connection Guide
21
VGA
15 way D-type connector
1 R
2 G
3 B
4 unused 
5 Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5v
10 Digital Ground (V Sync/DDC)
11 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
COMPONENT
5 x 75 ohm BNC
RGBHV  RGsB  YPbPr  YCbCr
Green     Green + Sync  Y    Y
Blue   Blue  Pb  Cb
Red   Red  Pr  Cr
Hsync
Vsync
Notes
 For full details of all input settings, 
see the INPUT menu in the 
Operating Guide.pin view of female...

Digital Projection E-Vision 8000 Series  WIRING DETAILS Connection Guide
22
S-Video input
4 pin mini-DIN
1 Y Ground
2 C Ground
3 Luminance (Y)
4 Chrominance (C)
Video input
1 x RCA Phono
Composite Video
pin view of female connector
Notes
 For full details of all input settings, 
see the INPUT menu in the 
Operating Guide. 
Rev F July 2014  

Digital Projection E-Vision 8000 Series  WIRING DETAILS Connection Guide
23
Control connections
LAN connection
10BaseT Unshielded Twisted Pair cable
The standard wire colors are as follows:
1 White / Orange stripe
2 Orange
3 White / Green stripe
4 Blue
5 White / Blue stripe
6 Green
7 White / Brown stripe
8 Brown
Crossed cable
(used to connect directly to a computer with no hub or network.) 
(Note that only the green and orange pairs are crossed)
1 White / Orange stripe  White / Green stripe 1
2 Orange...

Digital Projection E-Vision 8000 Series  WIRING DETAILS Connection Guide
24
RS232 Serial control input
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
Null-modem cable
(used to connect the projector to a computer)
RX 2 ---  3 TX
TX 3 ---  2 RX
GND 5 ---  5 GND
Wired Remote control connection
3.5mm mini jack
Tip Not connected
Ring Signal
Sleeve Ground
Screen Trigger output
3.5mm mini jack
Tip Signal
Sleeve Ground
Notes
 For full details of...