Digital Projection Projector E-Vision 6800 3D Series User Manual

							page 45
Operating Guide
USING THE PROJECTOR
Information menu
This menu gives information about software and hardware configuration, input 
source and lamp operating times It also allows you to restore the factor\
y default 
settings.
Source information
This page provides information about the currently selected input source\
.
NotesInformation
SelectItem [RETURN]
Back
SerialNumber:
Software Version1:
Filter Time:
Power OnTime:
Source Information
Model:
8 
E-Vision
6800WUXGA 3D
Software Version2:
Adjust
W444AAAAA0000
MD 00-0000- AA00-AA00
SD00-AA 00-0000
00005[ H]
00005[ H]
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 46
Operating Guide
MENU MAP
Menu Map
Menu Submenus and controls
INPUT 
HDMI, DVI-D, HDBaseT, VGA, Component 1, Component 2, S-Video, Video
TEST PATTERN 
Off, White, Black, Red, Green, Blue, Crosshatch, Burst, H Ramp, Color Bar, Checkerboard
LENS 
Zoom, Focus, Shift V, Shift H (commands, adjustment via arrow buttons)
IMAGE
Image Mode : Bright, Presentation, Video
Brightness, Contrast: sliders, 0 to 200 (100)
Gamma: 1.0, 1.8, 2.0, 2.2, 2.35, 2.5
Dynamic Black: On, Off
Saturation, Hue: sliders, 0 to 200 (100)
Sharpness: slider, 0 to 31
Noise Reduction: slider, 0 to 15
Position And Phase 
VGA Setup: H Total, H Start, H Phase, V Start: sliders, 0 to 200 (100)
Digital Alignment
     Digital Zoom: slider
     Digital Pan: slider
     Digital Scan: slider
     Reset (command)
H/V Alignment
     H Zoom: slider
     V Zoom : slider
      H Shift: slider
     V Shift: slider
     Reset (command)
Resync (command)
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be lighter 
in color in the OSD.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide.
 Some settings are associated with 
the current input and the value of 
the 
Image Mode setting (Bright, 
Presentation or Video). The 
projector automatically stores values 
of such settings to reuse when an 
Input / Image Mode combination 
is selected again. For example, if 
you increase the 
Contrast value 
while on the DVI-D input with I
mage 
Mode
 set to Bright,  the next time 
you use the DVI-D input with 
Image 
Mode
 set to Bright, the projector 
will automatically set the same 
Contrast value.
  Settings NOT associated with an 
Input / Image Mode combination 
are called  global settings  and are 
indicated with a globe icon 
 in 
this section. 
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 47
Operating Guide
MENU MAP
COLOR
Color Space: Auto, YPbPr, YCbCr, RGB PC, RGB Video
Color Temperature: Native, 5500K, 6500K, 7800K, 9300K
Trim: Red Lift, Green Lift, Blue Lift, Red Gain, Green Gain, Blue Gain: s\
liders, 0 to 200 (100)
Hue / Saturation / Gain
Red: Hue, Saturation, Gain: sliders, 0 to 200 (100)
Green: Hue, Saturation, Gain: sliders, 0 to 200 (100)
Blue: Hue, Saturation, Gain: sliders, 0 to 200 (100)
Cyan: Hue, Saturation, Gain: sliders, 0 to 200 (100)
Magenta: Hue, Saturation, Gain: sliders, 0 to 200 (100)
Yellow: Hue, Saturation, Gain: sliders, 0 to 200 (100)
White: Hue, Saturation, Gain: sliders, 0 to 200 (100)
GEOMETRY
Aspect Ratio: 5:4, 4:3, 16:10, 16:9, 1.88:1, 2.35:1, Source, Unscaled
H Keystone , V Keystone : sliders, -30 to 30 (0)
Overscan: On, Off
3D
3D Format: Off, Auto, Side by Side, Top and Bottom, Frame Sequential
DLP Link: On, Off
3D Swap : Normal, Reverse
3D 24Hz Display: 96Hz, 144Hz
LAMPS 
Lamp Mode: Auto 1, Dual, Lamp 1, Lamp 2
Power Mode: Eco, Normal, Custom
Custom Power Level: 82% to 100%
High Altitude: On, Off
Information only: Lamp 1 Status, Lamp 2 Status
       Lamp 1 Time, Lamp 2 Time
       Lamp 1 Life Remaining, Lamp 2 Life Remaining
Menu Submenus and controlsNotes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide.
 Some settings are associated with 
the current input and the value of 
the 
Image Mode setting (Bright, 
Presentation or Video). The 
projector automatically stores values 
of such settings to reuse when an 
Input / Image Mode combination 
is selected again. For example, if 
you increase the 
Contrast value 
while on the DVI-D input with I
mage 
Mode
 set to Bright,  the next time 
you use the DVI-D input with 
Image 
Mode
 set to Bright, the projector 
will automatically set the same 
Contrast value.
  Settings NOT associated with an 
Input / Image Mode combination 
are called  global settings  and are 
indicated with a globe icon 
 in 
this section. 
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 48
Operating Guide
MENU MAP
SETUP 
Orientation: Desktop Front, Ceiling Front, Desktop Rear, Ceiling Rear
Network
IP Address: numeric input (default IP address is 192.168.0.100)
Subnet Mask, Gateway, DNS: numeric input
DHCP: On, Off
Apply (command)
Standby Power: On, Off
Information only: MAC Address
RS232
Baud Rate: 38400, 19200, 9600
Channel: Local, HDBaseT
Security
Control Panel Lock: On, Off
Security Lock: On, Off
Filter
Filter Message: Off, 100 hours, 200 hours, 500 hours, 1000 hours
Filter Reset (command)
System
Auto Source: On, Off
Auto Power Off: On, Off
Auto Power On: On, Off
Startup Logo: On, Off
Blank Screen: Logo, Blue, Black
Trigger: On, Off
Infrared Sensor: Both, Front, Rear
Resync Adjust: Always, Auto
Language: English, Français, Español, Deutsch, Português, 简体中文, 繁體中文, 日本語, 한국어
Factory Reset (command)
INFORMATION
Model, Serial Number, Software Version 1, Software Version 2, Filter Time, Power On Time
Source Information:
Active Source, Pixel Clock, Signal Format, H/V Refresh Rate, Sync Type, Sync Polarity, Scan 
Type, Video Type
Menu Submenus and controlsNotes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide.
 Some settings are associated with 
the current input and the value of 
the 
Image Mode setting (Bright, 
Presentation or Video). The 
projector automatically stores values 
of such settings to reuse when an 
Input / Image Mode combination 
is selected again. For example, if 
you increase the 
Contrast value 
while on the DVI-D input with I
mage 
Mode
 set to Bright,  the next time 
you use the DVI-D input with 
Image 
Mode
 set to Bright, the projector 
will automatically set the same 
Contrast value.
  Settings NOT associated with an 
Input / Image Mode combination 
are called  global settings  and are 
indicated with a globe icon 
 in 
this section. 
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							LENS SHIFTZOOM
–FOCUS+
MENU
ENTER RETURN
SOURCE
POWER WARNING
LAMP1LAMP2AU
TO
REMOTE COMMUNICATIONS GUIDE4 
Rev A Januar y 2015 
E-Vision 6800 3D Series
High Brightness Digital Video Projector  
						

							Remote Communications Guide
IN THIS GUIDE
IN THIS GUIDE
Introduction ........................................................................\
................................51
Network setup ...........................................................................................................51
Serial Port setup ........................................................................................................51
Protocol commands ..................................................................................................52
Examples .....................................................................................................\
...................52
Responses .....................................................................................................\
.................52
Command Guide ........................................................................\
........................53
Inputs .........................................................................................................................53
Test Patterns ..............................................................................................................53
Lens menu  .................................................................................................................53
Image menu ...............................................................................................................54
Color menu  ................................................................................................................55
Geometry menu .........................................................................................................55
3D menu .....................................................................................................................56
Lamps menu ..............................................................................................................56
Setup menu ................................................................................................................57
Information menu ......................................................................................................57
Web Configuration Utility ........................................................................\
.......58
Email settings ............................................................................................................59
Projector controls  .....................................................................................................60
PJLink security options ............................................................................................61
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 51
Remote Communications Guide
INTRODUCTION
Introduction
The projector can be controlled by using an external control system or a PC via an RS232 or LAN interface, using a terminal-emulation
program.
Network setup
1. Connect the projector to a LAN network.
2. Open the Setup > Network menu and edit network settings. The default IP address is 192.168.0.100 and the TCP port number is 7000.
Serial Port setup
• Baud rate: 9,600 bps (default), 19,200 bps or 38,400 bps.
• Data length: 8 bits
• Stop bits: one
• Parity: none
• Flow control: none
Notes
 Details of how to connect to 
the projector using the LAN or 
RS232 input, can be found in the 
Connections Guide.
  Furhter details about setting up 
a LAN or Serial connection and 
changing network settings can be 
found in the Operating Guide.
 Only one control path at a time 
should be used for protocol control. 
Attempts to send commands to both 
serial and network ports at the same 
time may result in unpredicatable 
behaviour.
 The baud rate can be adjusted. For 
details, see the Operating Guide.
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 52
Remote Communications Guide
INTRODUCTION
Protocol commands
Commands are used to simulate menu operations and determine the settings\
 of the projector, and use the following format:
• All commands consist of ASCII text strings starting with an asterisk and ending with an ASCII Carriage Return character  (code 13): 
*command operator  
• The  string determines which setting the command will affect.
• Spaces are required before the operator and before the value.
• The  string can take one of the following formats:
Command typeDescription
Set= Makes the setting take the .
Get?Asks what the current value is. 
The value is returned as an ASCII text string.
ExecutePerforms an action. No operator is entered for this type of command.
Examples
*orientation = 3    sets the orientation to Ceiling Rear (for a celing mounted projector positioned behind the screen)
*aspect.ratio ?   asks what the current aspect ratio is
*zoom.in     commands the projector to zoom in
*orientation=3   is an invalid instruction because of the missing spaces before the opera\
tor and the value
Responses
If the command has been successful, the projector response begins with ack (“acknowledged”). For example, if the command is *aspect.
ratio = 1 , the projector will return ack aspect.ratio = 1 . The projector will then will change the aspect ratio accordingly.
If the command has not been acknowledged, due to a syntax error or another problem, the projector response will be nack, followed by a 
brief description of the problem.
Notes
 To set the default value of a 
command, simply enter the 
command name and 
 , without 
an operator. For example 
*orientation  will set the 
orientation to 0 (Desktop Front).
  You must wait for the complete 
response to a command before 
sending another command.
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 53
Remote Communications Guide
COMMAND GUIDE
Command Guide
Protocol commands below are arranged in the order they appear in the OSD\
. Not all OSD settings have corresponding protocol commands.

Inputs
input= ?0 = HDMI 
1 = DVI-D 
2 = HDBaseT 
3 = VGA 
4 = Component 1 
5 = Component 2 
6 = S-Video 
7 = Video
Test Patterns
test.pattern= ?0 = Off 
1 = White 
2 = Black 
3 = Red 
4 = Green 
5 = Blue 
6 = Crosshatch 
7 = Burst 
8 = H Ramp 
9 = Color Bar 
10 = Checkerboard
Lens menu
lens.left(execute)
lens.right(execute)
lens.up(execute)
lens.down(execute)
zoom.in(execute)
zoom.out(execute)
focus.near(execute)
focus.far(execute)
Notes
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 54
Remote Communications Guide
COMMAND GUIDE

Image menu
picture.mode= ?0 = Bright 
1 = Presentation 
2 = Video
brightness= ?0 to 200 (integer)
contrast= ?0 to 200 (integer)
gamma= ?0 = 1.0 
1 = 1.8 
2 = 2.0 
3 = 2.2 
4 = 2.35 
5 = 2.5
dblack= ?0 = Off, 1 = On
sharpness= ?0 to 31 (integer)
nr= ?0 to 15 (integer)
resync(execute)
Notes
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015