Digital Projection Projector E-Vision 6800 3D Series User Manual

							page 25
Operating Guide
USING THE PROJECTOR
Using The Projector
Main menu
• Input 
Press ENTER to open the list of available inputs.
Use the UP  and DOWN  arrow buttons to select an input from the list, then 
press ENTER to confirm your choice.
Press MENU to return to the main menu.
• Test Pattern 
Choose from:
...Off, White, Black, Red, Green, Blue, Crosshatch, Burst, H Ramp, Color 
Bar, Checkerboard...
Use the LEFT  and RIGHT  arrow buttons to switch between values.
• Lens, Image, Color, Geometry, 3D, Lamps, Setup and Information 
Press ENTER to open these menus and access various settings.
Notes
 If no input is connected, the Image 
menu will be unavailable.
  Some settings are associated with 
the current input and the value of 
the 
Image Mode setting (Bright, 
Presentation or Video). The 
projector automatically stores values 
of such settings to reuse when an 
Input / Image Mode combination 
is selected again. For example, if 
you increase the 
Contrast value 
while on the DVI-D input with I
mage 
Mode
 set to Bright,  the next time 
you use the DVI-D input with 
Image 
Mode
 set to Bright, the projector 
will automatically set the same 
Contrast value.
  Settings NOT associated with an 
Input / Image Mode combination 
are called  global settings  and are 
indicated with a globe icon 
 in the 
Menu Map further in this guide. 
E-Vision 6800WUXGA 3D
SelectItem
[Enter] Submenu [Menu]
Exit
TestPattern
Lens
Color
Geometry
3D
Input
Off
8
8
 
8 
8 
HDMI
Image
Lamps
Setup
Information
8 
8 
8 
8 
E-Vision 6800WUXGA 3D
SelectItem
[Enter]Execute [RETURN]
Back
TestPattern
Lens
Color
Geometry
3D
Input DVI-D
HDBaseT VGA
Component 1
Component 2
HDMI
Image
Lamps
Setup
Information S-Video
Video
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 26
Operating Guide
USING THE PROJECTOR
Lens menu
Lens settings operate in Zoom/Focus and Shift mode.
When in Zoom/Focus mode:
• Use the UP and DOWN arrow buttons to adjust Zoom.
• Use the LEFT and RIGHT arrow buttons to adjust Focus.
When in Shift mode, use the arrow buttons to adjust Shift.
Press ENTER to switch between Shift and Zoom/Focus mode.
NotesLensControl
Enter toShift
Zoom
Focus
Lens Control
Enter toZoom/Focus
Shift V
Shift H
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 27
Operating Guide
USING THE PROJECTOR
Image menu
Image Mode
Choose from Bright, Presentation and Video.
Press ENTER to open the list.
Use the UP  and DOWN  arrow buttons to select an image mode from the list, 
then press ENTER to confirm your choice.
Press MENU to return to the main menu.
Brightness and Contrast
Highlight the setting you wish to edit, and then press ENTER, or the LEFT  or 
RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Notes
Image>>
Select Item
Adjust[RETURN]
Back
Brightness
Contrast
DynamicBlack
Saturation
Hue
Image
Mode100
100
2.2
Off
100
Bright
Gamma
Sharpness
Noise Reduction
Position AndPhase 100
150
8 
Resync Execute
Image>>
Select Item
[Enter]Execute [RETURN]
Back
Brightness
Contrast
DynamicBlack
Saturation
Hue
Image Mode
Presentation
Video
Bright
Gamma
Sharpness
Noise Reduction
Position AndPhase
Resync
Brightness 100
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 28
Operating Guide
USING THE PROJECTOR
Image menu continued from previous page
Gamma
Choose a de-gamma curve from 1.0, 1.8, 2.0, 2.2, 2.35 and 2.5.
Used correctly, the Gamma setting can improve contrast while maintaining good 
details for blacks and whites. 
If excess ambient light washes out the image and it is difficult to see details in dark 
areas, lower the Gamma setting to compensate. This improves contrast while 
maintaining good details for blacks. Conversely, if the image is washed out and 
unnatural, with excessive detail in black areas, increase the setting.
Dynamic Black
Set to On to allow for increased contrast in darker scenes by modulating the ligh\
t 
source.
Saturation, Hue, Sharpness and Noise Reduction
Highlight the setting you wish to edit, and then press ENTER, or the LEFT  or 
RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
NotesImage>>
Select Item
[Enter]Execute [RETURN]
Back
Brightness
Contrast
DynamicBlack
Saturation
Hue
Image
Mode
1.8
2.01.0
Gamma
Sharpness
Noise
Reduction
Position AndPhase
Resync2.2
2.35
2.5
Noise Reduction 0
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 29
Operating Guide
USING THE PROJECTOR
Image menu continued from previous page
Position and Phase
Press ENTER to open a submenu.
• VGA Setup
H Total, H Star t, H Phase, V Start 
Adjust these settings as required to suit the incoming image.
• Digital Alignment
Digital Zoom, Digital Pan, Digital Scan 
Select a digital alignment control.
Reset 
Press ENTER to reset all Digital Alignment settings to zero.
• H/V Alignment
H Zoom, V Zoom, H Shift, V Shift 
Select an alignment control.
Reset 
Press ENTER to reset all H/V Alignment settings to zero.
Highlight the setting you wish to edit, and then press ENTER, or the LEFT  or 
RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Resync
Press ENTER to force the projector to resynchronize with the current input.
Notes
 H Shift will only work if the image 
has been reduced horizontally using 
H Zoom. Likewise, V Shift will 
only work once 
V Zoom has been 
applied.
Image >>Position AndPhase
Select Item
[Enter] Submenu [RETURN]
Back
DigitalAlignment
H/V Alignment
VGA
Setup
8 8
 
8 
Image >>
Select Item
[RETURN]Back
Brightness
Contrast
DynamicBlack
Saturation
Hue
Image
Mode
100
100
2.2
Off
100
Bright
Gamma
Sharpness
Noise Reduction
Position AndPhase 100
150
8 
ResyncExecute
[Enter] Execute
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 30
Operating Guide
USING THE PROJECTOR
Color menu
Color Space
In most cases, the Auto setting determines the correct colorspace to use. If it 
does not, you can choose a specific colorspace:
Choose from Auto, YPbPr, YCbCr, RGB-PC and RGB-Video.
NotesColor>>
Select Item
[Menu]Exit
ColorTemperature
Trim
Color Space
6500K
8
8 
Auto
Hue /Saturation /Gain
Adjust
Color>>
Select Item
[Enter]Execute [RETURN]
Back
ColorTemperature
Trim
Color Space
YPbPr
YCbCr Auto
Hue /Saturation /Gain
RGB-PC
RGB- Video
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 31
Operating Guide
USING THE PROJECTOR
Color menu continued from previous page 
Color Temperature
Choose a value from 5500K (warmer) to 9300K (cooler) or Native (no 
correction).
NotesColor>>
Select Item
[Enter]Execute [RETURN]
Back
ColorTemperature
Trim
Color
Space
5500K
6500KNative
Hue /Saturation /Gain
7800K
9300K
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 32
Operating Guide
USING THE PROJECTOR
Color menu continued from previous page
Trim
Adjust the RGB lift and gain settings to improve the color balance of th\
e projected 
image.
Highlight the setting you wish to edit, and then either press ENTER to access it, or 
use the LEFT  and RIGHT  arrow buttons to switch between values.
Hue / Saturation / Gain
Press ENTER to open a submenu, then use the LEFT  and RIGHT  arrow 
buttons to move the sliders.
Hue
Adjust hue of the main color as shown below:
Main colorHue
RMagenta   Yellow
GYellow  Cyan
BCyan  Magenta
CGreen  Blue
MBlue  Red
YRed  Green
Saturation
When you adjust the saturation of the main color, the selected color becomes 
lighter or thicker.
Gain
When you adjust the gain of the main color, the selected color becomes brighter 
or darker.
NotesColor>>Trim
Select Item
Adjust[RETURN]
Back
GreenLift
Blue Lift
Green Gain
Blue Gain
RedLift
100
100
100
100
100100
Red Gain
Color >>Hue /Saturation /Gain
Select Item
[Enter] Submenu [RETURN]
Back
Green
Blue
Magenta
Yellow
White
Red
8
8
 
8 
8 
Cyan
8 
8
8
 
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 33
Operating Guide
USING THE PROJECTOR
Geometr y menu
This menu allows you to compensate for image distortions caused by an un\
usual 
projection angle or irregular screen surface.
Aspect Ratio
Choose from:
• 5:4
• 4:3
• 16:10
• 16:9
• 1.88:1
• 2.35:1
• Source
• Unscaled
To change the aspect ratio:
1. From the Main menu, open Aspect Ratio.
2. From the list on the right, select a new aspect ratio and press 
ENTER.
NotesGeometry>>
SelectItem
[Enter] Submenu [RETURN]
Back
HKeystone
V Keystone
Aspect
Ratio
Overscan Source
0
0
Off
Geometry >>
SelectItem
[Enter]Execute [RETURN]
Back
HKeystone
V Keystone
Aspect Ratio
4:3
16: 10
5:4
Overscan
16:9
1.88:1
2.35:1
Source
Unscaled
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 34
Operating Guide
USING THE PROJECTOR
Geometry menu continued from previous page
H Keystone and V Keystone
Use the H Keystone and V Keystone settings to compensate for any distortion 
caused by the projector being in a different horizontal or vertical plane to the screen.
Highlight the setting you wish to edit, and then press ENTER, or the LEFT  or 
RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Keystone example
1 The projector is positioned at an angle
2 The resulting image is distorted
3 The image is corrected when V Keystone is applied
Notes
123
HKeystone 0
V
Keystone 0
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015