Digital Projection Projector E-Vision 6800 3D Series User Manual

							page 35
Operating Guide
USING THE PROJECTOR
Geometry menu continued from previous page
Keystone settings
1 Projector to the left
The projector is positioned 
to the left of the screen.
To correct, apply a positive 
H Keystone value using 
the RIGHT arrow button.
2 Projector to the right
The projector is positioned 
to the right of the screen.
To correct, apply a negative 
H Keystone value using 
the LEFT arrow button.
3 Projector high
The projector is positioned 
above the screen at a 
downward angle.
To correct, apply a negative 
V Keystone value using 
the LEFT arrow button.
4 Projector low
The projector is positioned 
below the screen at an 
upward angle.
To correct, apply a positive 
V Keystone value using 
the RIGHT arrow button.
5 Projector straight
The projector is directly 
opposite the screen at a 
right angle both horizontally 
and vertically. 
No correction is needed.
Notes
Horizontal and vertical keystone corrections
1
4
2
53
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 36
Operating Guide
USING THE PROJECTOR
Geometry menu continued from previous page
Overscan
Set to On to compensate for noisy or badly defined image edges.
Image with noisy edgesOverscanned image
NotesGeometry>>
SelectItem
[Enter]Execute [
RETURN] Back
HKeystone
V Keystone
Aspect
Ratio
OnOff
Overscan
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 37
Operating Guide
USING THE PROJECTOR
3D menu
Use this menu to enable, disable and set up 3D input, as follows:
• 3D Format — Off, Auto, Side by Side, Top and Bottom and 
Frame Sequential.
• DLP Link — On (if you are using 3D glasses that can utilise the 
DLP Link® signal embedded in the image) and Off
• 3D Swap — Normal and Rever se (set to Rever se if the left- and 
right-eye images are displayed in the wrong order)
• 3D 24Hz Display — set to 96Hz or 144Hz depending on the 
source. This setting is disabled unless a 24Hz 3D input is detected.
The 3D Swap setting explained
The outgoing 3D frames are in pairs - the dominant frame being 
presented first. You can determine which frame should be the dominant 
one.
By convention the default setting is Left.
Notes
 If 3D Format is set to Off, or if 
no 3D signal is detected in 
Auto 
mode, the other 3D settings will be 
unavailable.
 Frame Sequential is supported on 
the DVI input only.
  3D video is only possible on the 
HDMI, HDBaseT and DVI inputs.
 The Frame Packing format is 
automatically detected by the 
projector.
 See also 3D types further in this 
guide.
3D >>
Select Item
[RETURN]Back
DLP-Link
3D Swap
3D
Format
3D 24Hz Display Off
Off
Normal 144 Hz
Item Adjust
Dominance Left
Dominance Right
LEFT 1 RIGHT 1 LEFT 2RIGHT 2 LEFT 3RIGHT 3
LEFT 3
RIGHT 1 LEFT 1RIGHT 2 LEFT 2RIGHT 3
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 38
Operating Guide
USING THE PROJECTOR
3D menu continued from previous page 
3D types
In most situations you can use the Auto setting to have the projector automatically detect the format. 
Otherwise, consider the notes below to help you set up the 3D input manu\
ally.
The following 3D formats are supported:
• Frame Packing 
This format will be detected, re-synchronised, frame-multiplied and displayed at 144 Hz with the left eye / 
right eye dominance automatically extracted from the video data.
• Top and Bottom 
Sets the projector to reformat the video frames and map them to the disp\
lay with the left eye / right eye 
dominance automatically extracted from the video data. 
• Side by Side (Half): interlaced and progressive, 50 and 60Hz 
The side-by-side image will be de-interlaced (if appropriate), resized and then sequentially displayed at 
100 or 120 Hz.  The left eye / right eye dominance will be automatically extracted from the video data.
• Frame Sequential 
An example of Frame Sequential  would be 60Hz (30 frames per eye in Left-Right sequence (L1, R1, 
L2, R2…) with 2x Frame Rate Multiplication, resulting in a displayed sequence at 120 Hz (L1, R1, L1, 
R1, L2, R2, L2, R2…). For sequential 3D, the projector will generate an output sync, but it may then be 
necessary to manually reset the dominance each time the player is starte\
d.
Notes
LRLR
Frame Sequential
L
R
Frame Packing
L
R
Top-and-Bottom
L R
Side-by-Side (Half)
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 39
Operating Guide
USING THE PROJECTOR
3D menu continued from previous page
Frame rate multiplication in 3D images
When displaying a low frame rate 3D video, the projector 
multiplies the frame rate to obtain a flicker-free image. For 
example, a 60Hz frame rate is doubled to 120 Hz, or a 48 Hz 
frame rate is tripled to 144 Hz.
Frame rate multiplication is an automatic process. It occurs in 
the background and cannot be modified by the user.
NotesL1R1L2
R2
L1
L1
R1R2
L2 L3
R2
R1
L3
L2IN
OUT
x2 example
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 40
Operating Guide
USING THE PROJECTOR
Lamps menu
• Lamp Mode 
Choose from Auto 1, Dual, Lamp 1 and Lamp 2.
• Power Mode 
Eco will automatically set the lamp power to 80%. Normal will set the power 
to 92%.Set to Custom if you wish to adjust the power manually, from 80% to 
100%.
• Custom Power Level 
Use the LEFT and RIGHT arrow buttons to set lamp power. This setting is 
only available if Power Mode is set to Custom.
• High Altitude 
On increases the fan speed to compensate for reduced air density at high 
altitude.
The following menu items show information only:
• Lamp 1 Status, Lamp 2 Status
• Lamp 1 Time, Lamp 2 Time
• Lamp 1 Life Remaining, Lamp 2 Life Remaining
NotesLamps>>
SelectItem
[RETURN]Back
PowerMode
Custom PowerLevel
Lamp
Mode
Lamp1Status
Adjust
Dual
Normal -----
High Altitude Off
Lamp 2Status
Lamp 1Time
Lamp 2Time
Lamp 1Life Remaining
Lamp 2Life Remaining On
On
00031 [H]
00015 [H]
98%
99%
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 41
Operating Guide
USING THE PROJECTOR
Setup menu
• Orientation 
Choose from Desktop Front, Ceiling Front, Desktop Rear and 
Ceiling Rear.
• Network 
Set up a LAN network connection.
• RS232 
Set up a serial connection. 
• Security 
Set up Control Panel Lock and Security Lock.
• Filter 
Set up filter exchange intervals and reset the filter timer.
• System 
Adjust various system settings.
• Factor y Reset 
Restore factory settings.
To restore the factory default settings:
1. Navigate to Factor y Reset and press ENTER.
2. When prompted, use the LEFT  and RIGHT  arrow buttons to 
highlight the OK button and then press ENTER to confirm your choice.
NotesSetup>>
Select Item [RETURN]
Back
Network
RS232
Filter
System
FactoryReset
Orientation
Execute
8
8
 
8 
8 
DesktopFront
Security
8 
Adjust
Reset Everything ?
CancelOK
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 42
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
Network
Set DHCP to On if the IP address is to be assigned by a DHCP server, or Off if it 
is to be set here.
• If DHCP is set to On, it will not be possible to edit IP Address, Subnet Mask, 
Gateway or DNS.
• If DHCP is set to Off:
1. Edit IP Address, Subnet Mask, Gateway and DNS as required.
2. Select Apply and press ENTER.
Standby Power
If this setting is On, the LAN socket remains active when the projector is in 
STANDBY mode. If the setting is Off, the LAN socket is disabled when the 
projector is in STANDBY mode.
RS232
• Baud Rate 
Choose between 38400, 19200 and 9600.
• Channel 
Choose between Local and HDBaseT.
NotesSetup>>Network
Select Item [RETURN]
Back
SubnetMask
Gateway
DHCP
Apply
Standby Power
IP
Address
On
8 
192.168.0.100
DNS
Adjust
255.255.255.00.0.0.0
0.0.0.0Off
MAC Address 00:18:37:16:ef:ca
Setup >>RS232
Select Item
[RETURN]Back
Channel
Baud
Rate 9600
Local
Item Adjust
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 43
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
Security
Control Panel Lock
Use this setting to lock the control panel keys.
To unlock the keys, press the DOWN arrow button and hold for 5 seconds.
Security Lock
When the Security Lock is enabled, a security password will need to entered 
before the projector can be used, or before the lock can be disabled.
When setting the lock for the first time, the password will need to be entered 
twice, to ensure that it has been entered correctly.
Filter
This menu allows you to set up a reminder that the filters are due for replacement 
and to reset the filter timer.
• Filter Message 
Choose from Off, 100 hours, 200 hours, 500 hours and 1000 hours.
• Filter Reset 
Press ENTER to reset the timer. 
Notes
 The password consists of a 
combination	of	five	presses	of	the	
arrow keys.
 Find	details	about	changing	filters	
in the Installation and Quick-Start 
Guide .
Setup >>Security
Select Item
[RETURN]Back
SecurityLock
Control
PanelLock Off
Off
Item Adjust
Setup >>Filter
Select Item
[RETURN]Back
FilterReset
Filter
Message Off
Execute
Item Adjust
Password
[RETURN] Back
Confirm
Password
Register
Password
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  
						

							page 44
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
System
• Auto-Source 
If this setting is On, the projector will automatically search for an active input 
source.
• Auto Power Off 
Set this to On if you want the projector to go into STANDBY mode when no 
input source is detected for 20 minutes.
• Auto Power On
• Set this to On if you want the projector to start up immediately when the 
mains is connected.
• Set this to Off if you want the projector to go into STANDBY mode when 
the mains is connected. In this case, the projector will not start up un\
til the 
POWER button is pressed on the control panel or the remote control.
• Startup Logo 
Set this to On if you want the DP logo to show when the projector is first 
switched on.
• Blank Screen 
Choose from Logo, Blue and Black.
• Trigger 
Choose from Screen, 16:9, TheaterScope, 4:3, 4:3 Narrow or RS232 to 
determine what will cause the trigger output to activate.
• Infrared Sensor 
Choose from Both, Front, Rear or HDBaseT.
• Resync Adjust
• Language 
Change the OSD language.
NotesSetup>>System
Select Item [RETURN]
Back
AutoPower Off
Auto Power On
Blank Screen
Trigger
Infrared Sensor
Auto
Source
Both
8 
Off
Startup Logo
Adjust
Off
Off
Off
Logo
Language Auto
Resync Adjust On
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015