Digital Projection Projector E-Vision 6800 3D Series User Manual

page 25
Operating Guide
USING THE PROJECTOR
Using The Projector
Main menu
• Input 
Press ENTER to open the list of available inputs.
Use the UP  and DOWN  arrow buttons to select an input from the list, then 
press ENTER to confirm your choice.
Press MENU to return to the main menu.
• Test Pattern 
Choose from:
...Off, White, Black, Red, Green, Blue, Crosshatch, Burst, H Ramp, Color 
Bar, Checkerboard...
Use the LEFT  and RIGHT  arrow buttons to switch between values.
• Lens, Image, Color, Geometry, 3D,...

page 26
Operating Guide
USING THE PROJECTOR
Lens menu
Lens settings operate in Zoom/Focus and Shift mode.
When in Zoom/Focus mode:
• Use the UP and DOWN arrow buttons to adjust Zoom.
• Use the LEFT and RIGHT arrow buttons to adjust Focus.
When in Shift mode, use the arrow buttons to adjust Shift.
Press ENTER to switch between Shift and Zoom/Focus mode.
NotesLensControl
Enter toShift
Zoom
Focus
Lens Control
Enter toZoom/Focus
Shift V
Shift H
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y...

page 27
Operating Guide
USING THE PROJECTOR
Image menu
Image Mode
Choose from Bright, Presentation and Video.
Press ENTER to open the list.
Use the UP  and DOWN  arrow buttons to select an image mode from the list, 
then press ENTER to confirm your choice.
Press MENU to return to the main menu.
Brightness and Contrast
Highlight the setting you wish to edit, and then press ENTER, or the LEFT  or 
RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press...

page 28
Operating Guide
USING THE PROJECTOR
Image menu continued from previous page
Gamma
Choose a de-gamma curve from 1.0, 1.8, 2.0, 2.2, 2.35 and 2.5.
Used correctly, the Gamma setting can improve contrast while maintaining good 
details for blacks and whites. 
If excess ambient light washes out the image and it is difficult to see details in dark 
areas, lower the Gamma setting to compensate. This improves contrast while 
maintaining good details for blacks. Conversely, if the image is washed out and...

page 29
Operating Guide
USING THE PROJECTOR
Image menu continued from previous page
Position and Phase
Press ENTER to open a submenu.
• VGA Setup
H Total, H Star t, H Phase, V Start 
Adjust these settings as required to suit the incoming image.
• Digital Alignment
Digital Zoom, Digital Pan, Digital Scan 
Select a digital alignment control.
Reset 
Press ENTER to reset all Digital Alignment settings to zero.
• H/V Alignment
H Zoom, V Zoom, H Shift, V Shift 
Select an alignment control.
Reset 
Press ENTER...

page 30
Operating Guide
USING THE PROJECTOR
Color menu
Color Space
In most cases, the Auto setting determines the correct colorspace to use. If it 
does not, you can choose a specific colorspace:
Choose from Auto, YPbPr, YCbCr, RGB-PC and RGB-Video.
NotesColor>>
Select Item
[Menu]Exit
ColorTemperature
Trim
Color Space
6500K
8
8 
Auto
Hue /Saturation /Gain
Adjust
Color>>
Select Item
[Enter]Execute [RETURN]
Back
ColorTemperature
Trim
Color Space
YPbPr
YCbCr Auto
Hue /Saturation /Gain
RGB-PC
RGB- Video...

page 31
Operating Guide
USING THE PROJECTOR
Color menu continued from previous page 
Color Temperature
Choose a value from 5500K (warmer) to 9300K (cooler) or Native (no 
correction).
NotesColor>>
Select Item
[Enter]Execute [RETURN]
Back
ColorTemperature
Trim
Color
Space
5500K
6500KNative
Hue /Saturation /Gain
7800K
9300K
   
Digital Projection E-Vision 6800 3D Series 
Rev A Januar y 2015  

page 32
Operating Guide
USING THE PROJECTOR
Color menu continued from previous page
Trim
Adjust the RGB lift and gain settings to improve the color balance of th\
e projected 
image.
Highlight the setting you wish to edit, and then either press ENTER to access it, or 
use the LEFT  and RIGHT  arrow buttons to switch between values.
Hue / Saturation / Gain
Press ENTER to open a submenu, then use the LEFT  and RIGHT  arrow 
buttons to move the sliders.
Hue
Adjust hue of the main color as shown below:
Main...

page 33
Operating Guide
USING THE PROJECTOR
Geometr y menu
This menu allows you to compensate for image distortions caused by an un\
usual 
projection angle or irregular screen surface.
Aspect Ratio
Choose from:
• 5:4
• 4:3
• 16:10
• 16:9
• 1.88:1
• 2.35:1
• Source
• Unscaled
To change the aspect ratio:
1. From the Main menu, open Aspect Ratio.
2. From the list on the right, select a new aspect ratio and press 
ENTER.
NotesGeometry>>
SelectItem
[Enter] Submenu [RETURN]
Back
HKeystone
V Keystone
Aspect...

page 34
Operating Guide
USING THE PROJECTOR
Geometry menu continued from previous page
H Keystone and V Keystone
Use the H Keystone and V Keystone settings to compensate for any distortion 
caused by the projector being in a different horizontal or vertical plane to the screen.
Highlight the setting you wish to edit, and then press ENTER, or the LEFT  or 
RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Keystone example
1...