Digital Projection Projector E-Vision 6800 3D Series User Manual

page 5
Installation and Quick-Start Guide
CHANGING THE LENS, LAMPS AND COLOR WHEEL
Changing The Lens, Lamps And Color Wheel
Removing the lens
1. Remove the lens cap.
2. Push in the lens release lever, and turn the lens anti-clockwise.
3. Remove the lens.
Fitting the lens
1. Position the lens so that the label marked ‘O’ is at the top, push in the lens release lever and and gently insert the\
 lens all the way into the 
lens mount.
2. Turn the lens clockwise until it clicks into place.
12
Notes
 Always...

page 6
Installation and Quick-Start Guide
CHANGING THE LENS, LAMPS AND COLOR WHEEL
Changing the lamp
1. Slide open the lamp compartment cover as shown in the picture.
2. Unscrew the two captive screws securing the lamp module.
3. Pull firmly upwards on the handle to remove the lamp module.
4. Insert a new lamp module.
5. Fasten the screws.
6. Replace the lamp compartment cover.
123
Notes
 Always allow the lamp to cool for 
5 minutes before:
  - disconnecting the power 
- moving the projector
 The lamp...

page 7
Installation and Quick-Start Guide
CHANGING THE LENS, LAMPS AND COLOR WHEEL
Changing the color wheel
1. Slide open the lamp compartment cover as shown in the picture.
2. Unscrew the four captive screws securing the color wheel.
3. Remove the color wheel.
4. Insert a new color wheel.
5. Fasten the screws.
6. Replace the lamp compartment cover.
456
321
Notes
 Always allow the lamp to cool for 
5 minutes before:
  - disconnecting the power 
- moving the projector
 The color wheel must be changed...

page 8
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing\
 by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that 
the projector is level, and perpendicular to the screen.  
Alternatively, five M4 bolts (max length 12 mm [0.5 in]) can be used to attach the...

page 9
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
• Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
• Wait until the self-test has completed and the Power indicator on the projector control panel shows amber. The lamp will be off and the 
projector will be in STANDBY mode.
• Press  on the control panel or POWER ON on the remote control.
The Power indicator on the...

page 10
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the lens
Zoom
• Use the ZOOM +/− buttons on the control panel or on the remote control to adjust the lens so that the image fills the screen.
Focus
• Use the FOCUS +/− buttons on the control panel or on the remote control to adjust the len\
s until the image is sharp.
Shift
• Use the LENS SHIFT arrow buttons on the control panel to adjust the position of the image,\
or press the LENS SHIFT button on the remote control then use...

page 11
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Switching the projector off
• Press  on the control panel or STANDBY on the remote control, then press the button a second time within 5 seconds to confirm your 
intention to switch off.
The lamp will go off, and the Power indicator on the control panel will flash amber for a few seconds whilst the lamp cools. The Power 
indicator on the control panel will then show amber and the projector wi\
ll be in Standby mode.
• Switch off at the...

Installation and Quick-Start Guide
   
Digital Projection E-Vision 6800 3D Series 
This page is intentionally left blank.  

LENS SHIFTZOOM
–FOCUS+
MENU
ENTER RETURN
SOURCE
POWER WARNING
LAMP1LAMP2AU
TO
CONNECTION GUIDE4 
Rev A Januar y 2015 
E-Vision 6800 3D Series
High Brightness Digital Video Projector  

Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs And Outputs ........................................................................\
.....15
Supported Signal Input Modes .....................................................................16
2D input modes  .........................................................................................................16
3D input modes .........................................................................................................18
Control...