Digital Projection Mercury 5000gv Dmd Projector Users Manual

2-11
Digital Projection   
MERCURY 5000gv2. Installation
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's three-pin plug to the AC IN of the projector, and then connect the other plug of the
supplied power cable in the wall outlet. 

2. InstallationDigital Projection   MERCURY 5000gv 
2-12
 

3

Projecting an Image

(Basic Operation) 
○○○○○○○○○○○○○○○○○○\
○○○○○○○○○○○○○○○○○○○○○○ 
1 Turning on the Projector ......................... 3-2 
2 Selecting a Source .................................. 3-3 
3 Adjusting the Picture Size and Position .. 3-3 
4 Correcting the Horizontal and 
Vertical Keystone Distor tion 
(DigiScale - 3D Reform) ............................  3-4 
5 Optimizing RGB Picture Automatically ....  3-6 
6 Turning Up or Down Volume ....................  3-6 
7 Turning off  the...

3-2
3. Projecting an Image
Digital Projection   
MERCURY 5000gv
This chapter describes how to turn on the projector and to project a pic\
ture
onto the screen.
1 Tur ning on the Projector
NOTE:
• The projector is turned on using the POWER ON button on the remote
control or the ON/STANDBY  button on the projector control panel. The
mains cable should not be unplugged whilst the projector is turned on
(see ‘Turning off the Projector’ at the end of this chapter).
• The projector has a feature to prevent...

3-3
Digital Projection   
MERCURY 5000gv3. Projecting an Image
2 Selecting a Source
Selecting the computer or video source
Press the Source/Number button
(0-9) to select input.
1 ...... RGB 1 input
2 ...... RGB 2 input
3 ...... DVI (DIGITAL) input
4 ...... VIDEO input
5 ...... S-VIDEO input
6 ......
Viewer
7 ...... LAN
8 ...... SLOT 1
9 ...... SLOT 2
0 ...... Sequentially selects: ........ RGB1 (VIDEO)  ¤
........ RGB2 (S-VIDEO)  ¤
........ RGB1 (VIDEO) etc
Using the Remote Control
NOTE: If no input...

3-4
3. Projecting an Image
Digital Projection   
MERCURY 5000gv
4 Cor recting the Horizontal and Ver tical
Keystone Distortion (DigiScale - 3D
Refor m)
Use the DigiScale - 3D Reform feature to correct keystone (trapezoidal)\
distortion to make the top or bottom and the left or right side of the screen
longer or shorter so that the projected image is rectangular.
In the following description, DigiScale - 3D Reform (Cornerstone) corr\
ec-
tion can be done with the USB mouse, remote control or cabinet...

Digital Projection MERCURY 5000gv	3. Projecting an Image 
3. Press the 3D REFORM button on the projector cabinet or the KEYSTONE button on the remote control. 
The Cornerstone adjustment screen is displayed. 
The Cornerstone adjustment screen will disappear when you move 
the USB mouse cursor. 
4. Point to one of the remaining 3 corners and left-click on it. 
Left-click on the corner. 
Screen 
5. Do the above step 4 for the other two corners so that the projected  area becomes smaller than the screen....

3. Projecting an ImageDigital Projection MERCURY 5000gv 
8. Use the SELECT button to select another icon which points in the direction. 
Screen 
On the Cornerstone adjustment screen, 
select “Exit” and then “OK”, or press the 
CANCEL button on the remote control. 
The confirmation screen is displayed. 
9. Press the SELECT or button to highlight the [OK] and press the 
ENTER button. 
This completes the keystone correction.

Selecting “Cancel” will return to the adjustment screen without sa\
ving

changes...

3-7
Digital Projection   
MERCURY 5000gv3. Projecting an Image
7 Tur ning off  the Projector
To turn off  the projector:First press the POWER (ON/STAND BY) button on the projector cabinet or
the POWER OFF button on the remote control for a minimum of two seconds.\
The POWER indicator will glow orange. After the projector turns off, the
cooling fans keep operating for 90 seconds (Cooling-off time).
NOTE: You cannot turn off the projector for 1 minute immediately after
turning on the projector.
CAUTION...

3. Projecting an ImageDigital Projection MERCURY 5000gv 
3-8