Digital Projection M-vision Cine 400 3d Series User Guides

Digital Projection M-Vision Cine 400 3D seriesIMPORTANT INFORMATIONRemote Communications Guide
Revision A, May 2012 Remote-01
Important information
Symbols used in this guide
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
FURTHER INFORMATION
This symbol shows important additional information.
Special formatting
 ●Buttons on the projector control panel or the remote control appear in BLOCK CAPITALS, e.g. MENU. Where...

Digital Projection M-Vision Cine 400 3D seriesINTRODUCTIONRemote Communications Guide
Revision A, May 2012 
Introduction
The projector can be controlled by using an external control system or a\
 PC via an RS232 or LAN interface, using a terminal-emulation 
program, such as HyperTerminal.
Operation commands are used to simulate menu operations and determine th\
e settings of the projector, and use the following format:
 ●All commands consist of ASCII text strings starting with the letters ‘op’, and...

Digital Projection M-Vision Cine 400 3D seriesTHE OPERATION COMMANDSRemote Communications Guide
Revision A, May 2012 
The operation commands

Main menu
aspect= ?0 = 16:9
1 = TheaterScope
2 = 4:3
3 = 4:3 Narrow
4 = Native
recall.mem= ?0 = Preset A
1 = Preset B
2 = Preset C
3 = Preset D
4 = Default
save.mem=0 = Preset A
1 = Preset B
2 = Preset C
3 = Preset D
overscan= ?0 = Off
1 = Crop
2 = Zoom
s3d.inputtype= ?0 = Off
1  = Auto
2 = Side by Side (Half)
3 = Top and Bottom
4 = Dual Pipe
s3d.dlplink= ?0 =...

Digital Projection M-Vision Cine 400 3D seriesTHE OPERATION COMMANDSRemote Communications Guide
Revision A, May 2012 

s3d.24p.mode= ?0 = 96Hz
1 = 144Hz
input= ?0 = HDMI 1
1 = HDMI 2
2 = RGB (D-sub)
3 = Component 1 (RCA)
4 = Component 2 (BNC)
resync(none)(none)
Image menu
brightness= ? + -0 - 200
contrast= ? + -0 - 200
saturation= ? + -0 - 200
hue= ? + -0 - 200
sharpness= ? + -0 - 200
nr= ? + -0 - 200
Advanced Image menu
colorspace= ?0  = Auto
1 = YPbPr (= REC709)
2 = YCbCr (= REC601)
3 = RGB-PC
4 =...

Digital Projection M-Vision Cine 400 3D seriesTHE OPERATION COMMANDSRemote Communications Guide
Revision A, May 2012 

color.gamut= ?0  = Auto 
1 = REC709 
2 = SMPTE C 
3 = EBU 
4 = Native
bc= ?0 = Off 
1 = On
adcontrast= ?0 = Off 
1 = On
red.offset= ? + -0 - 200
green.offset= ? + -0 - 200
blue.offset= ? + -0 - 200
red.gain= ? + -0 - 200
green.gain= ? + -0 - 200
blue.gain= ? + -0 - 200
vert.pos= ? + -0 - 200
hori.pos= ? + -0 - 200
phase= ? + -0 - 200
tracking= ? + -0 - 200
sync.level= ? + -0 - 200...

Digital Projection M-Vision Cine 400 3D seriesTHE OPERATION COMMANDSRemote Communications Guide
Revision A, May 2012 

osd.trans= ?0 = 0% 
1 = 25% 
2 = 50% 
3 = 75%
osd.timer= ?0 = Always On
1 = Display OSD for 10 sec.
2 = Display OSD for 30 sec.
3 = Display OSD for 60 sec.
osd.msgbox= ?0 = Off
1 = On
blank.screen= ?0 = Logo
1 = Black
2 = Blue
3 = White
auto.poweroff= ?0 = Off
1 = On
auto.poweron= ?0 = Off
1 = On
altitude= ?0  = Auto
1 = High
proj.mode= ?0 = Front Tabletop
1 = Front Ceiling
2 = Rear...

Digital Projection M-Vision Cine 400 3D seriesTHE OPERATION COMMANDSRemote Communications Guide
Revision A, May 2012 

Control menu
trig1= ?0 = Screen
1 = 16:9
2 = TheaterScope
3 = 4:3
4 = 4:3 Narrow
5 = RS232
6 = RS232 On
7 = RS232 Off
trig2= ?0 = Screen
1 = 16:9
2 = TheaterScope
3 = 4:3
4 = 4:3 Narrow
5 = RS232
6 = On
7 = Off
auto.source= ?0 = Off
1 = On
ir.enable= ?0 = Disable
1 = Enable
Service menu
model.name?
soft.version?
act.source?0 = HDMI 1
1 = HDMI 2
2 = RGB (D-sub)
3 = Component 1 (RCA)
4 =...

Digital Projection M-Vision Cine 400 3D seriesTHE OPERATION COMMANDSRemote Communications Guide
Revision A, May 2012 

total.hours?
factory.reset(none)(none)
pattern= ?0 = Off
1 = White
2 = Black
3 = Red
4 = Green
5 = Blue
6 = Cyan
7 = Magenta
8 = Yellow
9 = Chequer Board
10 = Alignment Grid
11 = Vertical Burst
12 = Horizontal Burst
13 = Color Bars
Miscellaneous commands
blue.only=0 = Off
1 = On
powon(none)(none)
powoff(none)(none)
status.check?0 = standby
1 = warm up
2 = imaging
3 = cooling
4 = error...