Digital Projection M-vision Cine 400 3d Series User Guides

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Advanced Image menu
Colorspace
In most cases, the Auto setting determines the correct colorspace to use. If 
it does not, you can choose a specific colorspace:
 ●REC709 sets the colorspace to that defined in ITU-R BT.709.
 ●REC601 sets the colorspace to that defined in ITU-R BT.601.
 ●RGB-PC uses RGB colorspace and sets black at 0 and white at 255. 
Known as Full Range.
 ●RGB-Video uses RGB colorspace...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Advanced Image menu continued from previous page
Color Gamut
In most cases, the Auto setting will determine the correct color gamut to 
use. If it does not, you can select the appropriate setting manually.
Each setting defines the precise hue of each primary (red, green and 
blue) and secondary (yellow, cyan and magenta) color component used to 
generate the image.
Use the LEFT  and RIGHT  arrow buttons...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Advanced Image menu continued from previous page
Fine Sync
 ●V Position and H Position 
Set the sliders as required.
 ●Phase 
Adjusts the phase of the pixel sampling clock relative to the incoming 
signal. Adjust the phase if noise is visible.
 ●Tracking 
Adjusts the frequency of the pixel sampling clock. Flicker or vertical 
banding indicate poor tracking.
 ●Sync Level 
Adjusts the voltage level of the...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
System menu
This menu contains the following settings:
 ●OSD Settings 
Controls the positioning and behavior of the OSD.
 ●Blank Screen 
Defines what appears on the screen while the projector is running with 
no input signal.
 ●Auto Power Off 
Set this to On if you want the projector to go into STANDBY mode 
when no input source is detected for 20 minutes.
 ●Auto Power On 
If this is On, the projector...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Control menu
 ●Triggers 
Choose from Screen, 16:9, TheaterScope, 4:3, 4:3 Narrow or RS232 
to determine what will activate each trigger.
 ●Auto-Source 
If this setting is On, the projector will cycle the inputs until a source is 
detected.
 ●Infrared Remote 
This setting switches the infrared sensors on and off.
Service menu
Factory Reset
To restore the factory default settings:
1. Navigate to Factory...

Digital Projection M-Vision Cine 400 3D seriesMENU MAPOperating Guide
Revision A, May 2012 
Menu map
Menu     Sub-menus and settings
MAIN
   Aspect Ratio 16:9, TheaterScope, 4:3, 4:3 Narrow, Native
   Presets
    Recall A, B, C, D, Default
    Save A, B, C, D
   Overscan Off, Crop, Zoom
   3D Control
    3D Format Off, Auto, Side by Side, Top and Bottom, Dual Pipe
    DLP Link Off, On
    3D Swap Normal, Reverse
    Dark Time 1ms, 1.5ms, 2ms, 2.5ms
    Sync Delay value between -3.0ms and 3.0ms (0.0ms)...

Digital Projection M-Vision Cine 400 3D seriesMENU MAPOperating Guide
Revision A, May 2012 
Menu     Sub-menus and settings
ADVANCED IMAGE
   Colorspace Auto, REC709, REC601, RGB PC, RGB Video
   Gamma Film (2.2), Video, Punch (2.0), Graphics, CRT (2.5)
   Color Temperature 5500, 6500, 7500, 9300, Native
   Color Gamut Auto, REC709, SMPTE-C, EBU, Native
   BrilliantColor Off, On
   Adaptive Contrast Off, On
   RGB Adjust
    Red Offset value between 0 and 200 (100)
    Green Offset value between 0 and...

Digital Projection M-Vision Cine 400 3D seriesMENU MAPOperating Guide
Revision A, May 2012 
Menu     Sub-menus and settings
SYSTEM
   OSD Settings
    Menu Position Left-Upper, Right-Upper, Left-Bottom, Right-Bottom, Center
    Menu Transaprency 0%, 25%, 50%, 75%
    Time Out 10 sec, 30 sec, 60 sec, Always On
    Message Box Off, On
   Blank Screen Splash, Black, Blue, White
   Auto Power Off Off, On
   Auto Power On Off, On
   Projection Mode Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling...

M-Vision Cine 400 3D series
High Brightness Digital Video Projector
16:9 widescreen display
Revision A, May 2012 112-857A
REMOTE COMMUNICATIONS GUIDE 

Digital Projection M-Vision Cine 400 3D series Remote Communications Guide
Revision A, May 2012 
CONTENTS
Important information ......................................................Remote-01
Symbols used in this guide .......................................................................Remote-01
Special formatting ........................................................................\
..............Remote-01
Product revision ........................................................................\...