Digital Projection M-vision Cine 400 3d Series User Guides

Digital Projection M-Vision Cine 400 3D seriesSUPPORTED SIGNAL INPUT MODESConnection Guide
Revision A, May 2012 
SignalResolutionFrame Rate 
(Hz)
3D Support
ComponentVGA RGBHVVGA YUVHDMI RGBHDMI YUV 8 bitHDMI YUV 10 bitHDMI YUV 12 bit
Frame PackingSide by Side (Horizontal)Top and Bottom
HDTV
720p23.98
720p24
720p29.97
720p30
720p50
720p59.94
720p60
1080i50
1080i (Aus)50
1080i59.94
1080i60
1080p23.98
1080p24
1080p25...

Digital Projection M-Vision Cine 400 3D seriesCONTROL CONNECTIONSConnection Guide
Revision A, May 2012 
Control connections
Service port
The service port is used to download firmware updates issued from time to 
time by Digital Projection.
LAN and RS232
All of the projector’s features can be controlled via a LAN or 
serial connection using the text strings described in the Remote 
Communications Guide.
Connecting to the projector via a web-based interface is described in th\
e 
next chapter, LAN IP...

Digital Projection M-Vision Cine 400 3D seriesLAN IP CONFIGURATION UTILITYConnection Guide
Revision A, May 2012 
LAN IP configuration utility
LAN IP configuration can be carried out using a web browser:
1. Point your browser at the projector by typing the LAN IP address into 
the address bar, then press the ENTER key. 
The embedded IP Configuration webpage should appear.
2. Enter the settings as required, then click Save.
Notes
The default LAN IP address is 
192.168.0.100.
Con-07
The IP Configuration page 

Digital Projection M-Vision Cine 400 3D seriesWIRING DETAILSConnection Guide
Revision A, May 2012 
Wiring details
Signal inputs
Component 1
3 x RCA Phono connector
Component 2
3 x 75 ohm BNC
RGsBYCbCrYPbPr
RCrPr
G + SyncGY
BCbPb
RGB input
15 way D-type connector
1R
2G
3B
4unused
5Digital Ground (H Sync)
6R Ground
7B Ground
8G Ground
9+5v
10Digital Ground (V Sync/DDC)
11unused
12SDA
13H Sync
14V Sync
15SCL
Notes
For full details of all input settings, 
see the Main menu section in the 
Operating Guide....

Digital Projection M-Vision Cine 400 3D seriesWIRING DETAILSConnection Guide
Revision A, May 2012 
HDMI inputs
19 way type A connector
1TMDS Data 2+
2TMDS Data 2 Shield
3TMDS Data 2-
4TMDS Data 1+
5TMDS Data 1 Shield
6TMDS Data 1-
7TMDS Data 0+
8TMDS Data 0 Shield
9TMDS Data 0-
10TMDS Clock+
11TMDS Clock Shield
12TMDS Clock-
13CEC
14not connected
15SCL (DDC Clock)
16SCA (DDC Data)
17DDC/CEC Ground
18+5 V Power
19Hot Plug Detect
Notes
For full details of all input settings, 
see the Main menu section in...

Digital Projection M-Vision Cine 400 3D seriesWIRING DETAILSConnection Guide
Revision A, May 2012 
Control connections
Wired remote control connection
3.5mm mini jack
TipPower
RingSignal
SleeveGround
Serial control input
1unused
2Received Data (RX)
3Transmitted Data (TX)
4unused
5Signal Ground
6unused
7unused
8unused
9unused
Straight-through cable
(used to connect the projector to a computer)
RX2---2TX
TX3---3RX
GND5---5GND
Serial port settings
Baud rate9,600 bps
Data length8 bits
Stop bitsone...

Digital Projection M-Vision Cine 400 3D seriesWIRING DETAILSConnection Guide
Revision A, May 2012 
LAN connection
TCP Port number: 7000
Default IP address: 192.168.0.100
10BaseT Unshielded Twisted Pair cable
3D sync connection
Pin 1 +5V
Pin 2 Ground
Pin 3 Stereo sync
Notes
Con-11
Top view of cable connector (pin is underneath)
2
3
1
VESA 3-pin Mini DIN 

This page is intentionally left blank. 

M-Vision Cine 400 3D series
High Brightness Digital Video Projector
16:9 widescreen display
Revision A, May 2012 112-856A
OPERATING GUIDE 

Digital Projection M-Vision Cine 400 3D series Operating Guide
Revision A, May 2012 
Important information ..............................................................Op-01
Symbols used in this guide ........................................................................\
.......Op-01
Special formatting ........................................................................\
......................Op-01
Product revision ........................................................................\...