Digital Projection M-vision Cine 400 3d Series User Guides

Digital Projection M-Vision Cine 400 3D seriesIMPORTANT INFORMATIONOperating Guide
Revision A, May 2012 Op-01
Important information
Symbols used in this guide
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
FURTHER INFORMATION
This symbol shows important additional information.
Special formatting
 ●Buttons on the projector control panel or the remote control appear in BLOCK CAPITALS, e.g. MENU. Where necessary, the name of...

Digital Projection M-Vision Cine 400 3D seriesUSING THE MENUSOperating Guide
Revision A, May 2012 
Using the menus
Opening the OSD
Access the various menus using either the projector control panel or the\
 
remote control. On either device,
 ●press the MENU button.
The on-screen display (OSD) opens showing the list of available menus.\
Opening a menu
Move up and down the list using the UP and DOWN  arrow buttons. 
To open a menu,
 ●press ENTER (on the remote control) or SELECT (on the control 
panel)....

Digital Projection M-Vision Cine 400 3D seriesUSING THE MENUSOperating Guide
Revision A, May 2012 
Inside a menu
When you open a menu, the page consists of the following elements:
 ●Title bar at the top 
Shows which menu (and sub-menu) you have accessed.
 ●Highlighted item
 ●Available and unavailable items 
Unavailable items appear grayed out. Whether an item is available may 
depend on other settings.
 ●Text next to each item 
Shows whether the item:
 ●has a value that can be changed (shows the current...

Digital Projection M-Vision Cine 400 3D seriesUSING THE MENUSOperating Guide
Revision A, May 2012 
Editing projector settings
If the highlighted menu item is a setting with a list of values to choos\
e from, 
you can change the value in two different ways.
Choosing a value from a list
To access the list of values and then make a selection:
1. Highlight the menu item and press ENTER/SELECT.
2. On the new page that opens, use the UP  and DOWN  arrow 
buttons to highlight a value, then press ENTER/SELECT...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
A tour of the menus
The projector settings are grouped into six menus as shown in the 
illustration.
Main menu
Selecting Main from the top level opens the Main menu.
Notes
Op-05
IMAGE
MAIN
ADVANCED IMAGE SYSTEM
CONTROL
SERVICE
Presets
Overscan
3D Control
Input Select
Resync
MAIN >>



Off
HDMI 1
Aspect Ratio
Native 

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Main menu continued from previous page
Aspect Ratio
This setting allows you to switch between 16:9, TheaterScope, 4:3, 4:3 Narrow and Native.
Examples
Examples with anamorphic lens
Notes
The Native image examples 
shown here have far fewer pixels 
than the 1920 x 1080 of the 
projector. Your image may be 
different.
When displaying a 16:9 image, 
DO NOT use an anamorphic lens.
An anamorphic lens...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Main menu continued from previous page
Presets
The current image settings can be saved a preset, which you can recall 
later. The default settings can be recalled at any time as well.
Up to four custom presets can be stored for each  input source you use.
The following settings are saved in a preset:
 ●From the Main menu — Aspect Ratio and Overscan
 ●From the Image menu — Brightness, Contrast,...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Main menu continued from previous page
3D Control
Use this sub-menu to enable, disable and set up 3D input, as follows:
 ●3D Format — Off, Auto (recommended), Side by Side, Top and 
Bottom, Dual Pipe
 ●DLP Link — On (if you are using 3D glasses that can utilise the DLP 
Link® signal embedded in the image) and Off
 ●3D Swap — Normal and Reverse (set to Reverse if the 3D images 
are displayed in the wrong...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Main menu continued from previous page
Input Select
This setting controls the input source used by the projector. Choose from 
the following input sources:
 ●HDMI 1
 ●HDMI 2
 ●RGB
 ●COMP 1
 ●COMP 2
To change the input source, highlight Input Select, and then:
 ●Either toggle between the available sources using the 
LEFT  and RIGHT  arrow buttons
 ●Or press ENTER/SELECT and then select a source from the...

Digital Projection M-Vision Cine 400 3D seriesA TOUR OF THE MENUSOperating Guide
Revision A, May 2012 
Image menu
Highlight the setting you wish to edit, and then press ENTER/SELECT, or 
the LEFT  or RIGHT  arrow button to open the slider.
Use the LEFT  and RIGHT  arrow buttons to adjust the slider.
Press MENU to close the slider.
Notes
Op-10
Contrast
IMAGE >>
Brightness100
100
Saturation 100
Hue 100
Sharpness
Noise Reduction 0
0