Dell Projector S320/S320wi User Manual

  
   
 
   
 
 
       
   
       
AUTO SOURCE—Select Off (the default) to lock the current input signal. If 
you press the Source button when the  Auto Source mode is set to  Off, you 
can manually select the input signal. Select  On to auto detect the available 
input signals. If you press the  Source button when the projector is on, it 
automatically finds the next available input signal. 
A
UTO KEYSTONE—Select  On to automatically adjust image distortion caused 
by tilting the projector. 
P...

 
 buttons on the control panel simultaneously for 2 seconds. You can also 
invoke the test pattern 2 by pressi ng and holding down 
and  buttons 
on the control panel simultaneously for 2 seconds. 
Test Pattern 1: 
Test Pattern 2: 
FACTORY RESET—Select and press  to reset all settings to its factory 
default. The below warning message appears: 
Reset items include both computer  sources and Video source settings. 
Using Your Projector 
62 
Downloaded From projector-manual.com DELL Manuals 

  
 
 
             
 
 
 
 
   
 
   LAN SETTINGS—Select and press  to activate LAN settings. The LAN settings 
menu provides the following options: 
WIRELESS AND LAN—Select  Enabled to activate the Wireless and LAN 
function. 
DHCP— If a DHCP server exists in the  network to which the projector is 
connected, the IP address will automatically be acquired when you select 
DHCP On. If DHCP is Off, manually  set the IP Address, Subnet Mask, 
and Gateway. Use 
and to select  the number of IP address,...

  
 
     
   
 
   
   
3.	  After the IP Address, Subnet Mask, Gateway, and DNS is set up, 
select  Store and press 
 button to store the settings. 
4.	  If you select Store  without pressing the Enter button, the system will 
keep the original settings. 
R
ESET—Press  to reset network configuration. 
W
IRELESS SETTINGS—Select and press  to activate wireless settings. The wireless 
settings menu provides the following options: 
WIRELESS—If your projector has been installed the wireless dongle, this...

  
   
   
 
   
 
     
 
3.	  After the IP Address, Subnet Ma sk, Gateway, and DNS is set up, 
select  Store and press 
 button to store the settings. 
4.	  If you select Store  without pressing the Enter button, the system will 
keep the original settings. 
R
ESET—Press  to reset wireless configuration. 
M
ENU SETTINGS— Select and press to activate the menu settings. The menu 
settings consists of the following options: 
MENU POSITION—Allows you to change the position of the OSD menu on 
the screen....

 
   
   
 
  
   
   
 
a 
Go to  Menu Settings , press  and then select  Pa s s w o r d to Enabled 
the password settings. 
b	 Enabling the Password function will  pop up a change screen. Key in a 
4-digit number from the screen and press 
. 
S320 Password screen  S320wi Password screen 
c To confirm, enter the password again. 
d If the password verification is succ
essful, you may resume with accessing 
the projector's functions and its utilities. 
2 If you have entered an incorrect password, you...

 
CHANGE PASSWORD—Key in the original password. Then, enter the new 
password and confirm the new password again. 
S320 Change Password screen  S320wi Change Password screen 
POWER SETTINGS—Select and press  to activate power settings. The power 
settings menu provides the following options: 
Using Your Projector  67 
Downloaded From projector-manual.com DELL Manuals 

  
   
   
   
     
   
 
 QUICK SHUTDOWN—Select  On to turn off the projector with a single press of 
the Power button. This function allows the projector to quickly power off 
with an accelerated fan speed. Slightly  higher acoustic noise is expected 
during quick power off. 
NOTE: Before you turn on the projector  again, wait for 60 seconds to 
allow the internal temperature to  stabilize. The projector will take a 
longer time to turn on if you try  to power on immediately. Its cooling fan 
will run...

    
     
INTERACTIVE SETTINGS—Select and press  to activate Interactive settings. The 
Interactive settings menu provides the following options: 
NOTE: The S320 projector must be installed with a Interactive Module 
Kit if you want to use the Interact ive feature. Refer to "Installing the 
Optional Interactive Module Kit" on page 15. 
I
NTERACTIVE—Default option is  On. Select Off to disable the Interactive 
Pen function. 
NOTE: 
1.	  Ensure that the Interactive P en is connected. See...

     
 
 
 
 
 
   
    
 
  
 
 
 
POINTER MOTION—Allows you to select the Pointer Motion mode: 
Normal, Draw, and Stable. 
•Normal 
— In the Normal mode, pressing the Left button of the 
Interactive Pen holds the position of the pointer for a moment. This 
mode is best to use the Interactive Pen like a mouse, i.e., for left click 
and double click function. 
•Draw 
— In Draw mode, the position can move freely for drawing. 
This mode is best for drawing or writing on the screen. 
•Stable 
— In the...