Dell Projector S320/S320wi User Manual

Enable Wireless or LAN on the Projector 
1	 Install the optional wireless module kit (optional in S320). See "Installing the 
Optional Wireless Module Kit" 
on page 14.
 NOTE: If you select install the LAN module  kit (optional), see "Installing the 
Optional RJ45 Kit" on page 16. 
2	 
Connect the power cable and turn on  the projector by pressing the power 

button.

 NOTE: 
a	 If the LAN is used for audio projection, follow  these steps to enable Wireless 
and LAN function (default is...

 
    
   
    
  
      
 
The Wireless Guide Screen shown below appears: 
4	 Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP 

ADDRESS
. You will need these information to log in later.
 
Install the Wireless Applicatio n Software on Your Computer 
5	 "Wireless Application Software" is required if the Wireless or LAN is used for 
the Audio Projection set-up. Please down load and install the software the first 
time you use Audio Projection. If it is already installed, skip 
Step 5 - 6....

 NOTE: If the LAN is used for audio projection, connect the LAN cable to the 
projector and the computer. 
Launch the Wireless Application 
7	 Once the installation is complete, the program will launch automatically. Or 
you can double-click the 
or  icon on the desktop to start the 
application. 
 NOTE: 
1	  When you select the LAN for projection, click " Skip". 
2	  When you select the Wireless for projection, select the  Dell S320 Wireless 
or Dell S320wi Interactive , and the click...

  
   
   
    
 
  
    
     
   
 
Login 
8	 To communicate with your projector, en ter the Login Code (see Step 4), and 
then click OK. 
NOTE: If the  IP Address  is not detected, enter the  IP Address displayed at the 
bottom left corner of the wireless screen. 
9	 
You are now logged into the S320 or S320wi Wireless Application. Click the 
"Play" button in the application to starting the LAN or wireless projection. 
NOTE: You may use the controls to either project in full screen mode or in...

  
 
  
   
Managing the Projector From Web 
Management (for Wireless Network) 
Configuring the Network Setting 
If the projector is connected to a network, you can access the projector using a web 
browser. For configuring the network setting, refer to "LAN Settings" on page 63. 
Accessing Web Management 
Use Internet Explorer 5.0 and above or Firefox 1.5 and above and enter the IP 
address. You can now access Web Management and manage the projector from a 
remote location. 
NOTE: Web management...

 
Download the Wireless Application Software 
See also "Wireless Networking Installation" on page 74. 
Click the Download  button of the corresponding operating system of your 
computer. 
Using Your Projector 
96 
Downloaded From projector-manual.com DELL Manuals 

   
 
  
   
     
 
   
   
 
 
 
Conference Control 
This allows you to host conference presentations from different sources without 
using projector cables and lets you control how each presentation will appear on 
screen. 
NOTE: Without Conference Play Control, the last  user to hit the "Play" button on 
the application will take control of the full-screen projection. 
Computer Name : Lists the computers logged for conference control. 
Play Control : Click the buttons to control how each...

 
Managing Properties 
Admin 
An administrator password is required to access the Admin page. 
•	  Admin Password : Enter the administrator password and then click  Login. 
The default password is "admin". To change the password, see "Change 
Passwords" on page 103. 
Using Your Projector 
98 
Downloaded From projector-manual.com DELL Manuals 

 
System Status 
Displays the Network Status , Connection Status , and Projector Status 
information. 
Using Your Projector 99 
Downloaded From projector-manual.com DELL Manuals 

 
  
 
Network Status 
See OSD section on page 63. 
IP Setup  •	  Choose  Obtain an IP a ddress automatically to assign an IP address to the 
projector automatically, or  Use the following IP address  to assign an IP 
address manually. 
DHCP Server Setup  •	  Choose  Auto to automatically set up the  Start IP, End IP , Subnet Mask, 
Default Gateway , and DNS Server  address from a DHCP server, or  Disable 
to disable this function. 
Wireless Setup  •  Choose  Enable to set up the  Region, SSID, SSID...