Dell 1320c User Guide

back to contents page  
Operator Panel   
   
   Using the Operator Panel  
   Understanding the Operator Panel Lights  
   Restoring the factory settings  
Using the Operator Panel  
   
The printer operator panel has two buttons and several indicators that show the status of the printer.  
 
   
1. Continue button/indicator  
 
l Press this button to start single sheet feeder or duplex printing.    
 
l Press and hold this button to print the Report page.    
 
2. Ready/Data indicator  
Indicates the...

Understanding the Operator Panel Lights  
   
The operator panel lights mean different things, depending on their sequence. Orange or green lights that are off, on, and/or blinking indicate printer 
conditions such as printer status, intervention (for example, out of paper), or service.  
   
 
   
Common Light Sequences  
   
The following table shows the most common light status.  
  Orange blinks   A paper jam occurred.  
Single Sheet Feeder   Green on   Paper is set to the single sheet feeder....

Paper Conditions  
   
The following table shows the paper status.  
   
-    
  -   -   -   -   -   Calibrating  
-    
  -   -   -   -   -   Warming up  
-    
  -   -   -   -   -   Waiting for incoming data  
-    
  -   -   -    
  -   Initializing NVM  
-    
  -   -   -   -   -   On Diagnosis   
when starting  
-    
  -   -   -   -   -   In power saver mode  
1   2   3   4   5   6   7   Printer status  
-   -    
  -   -   -   -   Paper is loaded in the Tray 1.  
-   -   -    
  -   -   -   Paper...

   
The following conditions prompt you to load paper and press the Continue key. Click the links in the right column for more information on what it means and 
what you can do.  
 
When an Error Occurred  
   
The following table shows the location where an error occurred.  
  1   2   3   4   5   6   7   Action  
 
   
   
  -   -   -   -   Load paper for side 2 in the Tray 1. See  Manual Duplex Printing from Tray 1 .  
 
   
   
  -   -   -   -   Press the Continue key. See  Manual Duplex Printing from...

Operator Call Errors  
   
Press and hold the  Continue  button when an error occurs. You can obtain the detailed information from the operator call error.  
     
-   -   -    
  -    
  -   The wrong size of paper is loaded in the single sheet feeder. See  Identifying Print Media Sources and Specifications .  
-   -   -   -   -    
  -   Operator call errors  
-   -   -   -    
   
  -   An error occurred in the specified toner cartridge. See  Replacing Toner Cartridges .  
-   -   -   -    
  -   -...

Toner Errors  
 
Errors in the PHD Unit, Belt Unit, Fuser Unit, and CTD Sensor  
 
Fatal Errors  
   
The following table shows fatal errors. Contact your Dell supplier to notify the printer status associated with each error.  
  1   2   3   4   5   6   7   Toner status  
-    
   
  -    
   
  -   The specified toner is not installed.  
-    
  -    
   
   
  -   The low toner in the specified toner cartridge.  
-    
  -   -    
   
   
  The CRUM ID error in the specified toner cartridge.  
1   2...

ESS - Related Errors  
           
-    
   
  -   -   -   -    
   
  -   CTD (Conductivity Temperature Depth) sensor failure  
-    
  -    
   
    -   -   -    
  -   Fan motor failure  
-    
  -    
  -    
    -   -    
  -   Motor failure  
-    
  -    
  -   -    
    -    
  -   MCU (Machine Control Unit) error  
-    
  -    
  -   -   -    
   
  -   Environmental sensor failure  
-    
   
   
   
    -   -   -    
  -   Solenoid error in the K mode.  
-    
   
   
  -    
    -   -...

Restoring the factory settings  
   
You can restore the factory settings for your printer if you cannot use the printer with your computer.  
   
To restore the factory settings:  
1. Ensure that the printer is turned off.  
 
2. Open the side cover.  
 
3. While holding down the Continue and Cancel buttons at the same time, turn on the printer.  
 
4. After all the indicators are turned on, release the Continue and Cancel buttons.  
 
5. After the Continue, Error, and Ready/Data indicators go out,...

back to contents page  
Printer Settings   
   
You can change most system settings from your software programs. If your printer is attached to the network, you can change settings from the  Dell Printer 
Configuration Web Tool . To launch the  Dell Printer Configuration Web Tool , type the printer IP address in your Web browser. To find your printers IP 
address, see  Printing a Printer Settings Page .  
   
Settings from the software program update the default system settings for the printer. Settings...

1. Click  Start ®   All Programs ®   Dell Printers ®   Additional Color Laser Software ®   Status Monitor Console .  
The  Printer Selection  dialog box opens.  
 
2. Click  Dell Color Laser 1320c  listed in Printer Name.  
The  Dell Color Laser 1320c Launcher  window opens.  
 
3. Click the  Tool Box  button.  
The  Tool Box  opens.  
You can also launch the Tool Box from the printer icon on the taskbar.  
 
4. Click the  Printer Maintenance  tab.  
 
5. Select the desired menu item.  
Each menu item...