Dell 1320c User Guide

l Paper should be punched at the paper manufacturer and not drilled into paper already packaged in a ream. Drilled paper can cause jams when multiple 
sheets feed through the printer. This may result in a paper jam.   
 
     
l Pre - punched paper can include more paper dust than standard paper. Your printer may require more frequent cleaning and feed reliability may not be as 
good as standard paper.   
 
     
l Weight guidelines for pre - punched paper are the same as non - punched paper....

l Set the paper type to  Label  from the printer driver.   
 
     
l Do not load labels together with paper in the same tray. This may result in a jam.   
 
     
l Do not use label sheets with a slick backing material.   
 
     
l Do not print within 1 mm (0.04 inches) of the die cut.  
 
     
l Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets also contaminate your printer and your 
cartridge with adhesive, and could void your...

Print Media Supported  
   
Setup Paper Type  
    Kakukei 3 (216x277mm)   Y   Y  
C5 (162x229mm)   Y   Y  
Monarch (3.875x7.5 in)   Y   Y  
Envelope #10 (4.125x9.5 in)   Y   Y  
DL(110x220mm)   Y   Y  
Postcard JPN (100x148mm)   Y   Y  
Postcard JPN (148x200mm)   Y   Y  
Letter (8.5x11 in)   Y   Y  
Legal (8.5x14 in)   Y   Y  
Folio (8.5x13 in)   Y   Y  
Executive (7.25x10.5 in)   Y   Y  
Custom*   Y   Y  
*Custom:  76.2 and 220.0 mm or between 3.00 and 8.66 inches  
127.0 and 355.6 mm or between 5.00...

back to contents page  Coated   106 - 163 (Low Speed)   Inkjet printer paper cannot be used.  
Coated Thick   164 - 216 (Low Speed)   Inkjet printer paper cannot be used.  
Coated JPN   95 - 105 (Mid Speed)   -  
Label   3R7408   Inkjet printer paper cannot be used.  
Envelopes   -   -    

back to contents page  
Loading Print Media   
   
Loading print media properly helps prevent jams and ensures trouble - free printing.  
   
Before loading print media, identify the recommended print side of the print media. This information is usually on the print media package.  
   Tray 1  
   Loading Print Media in Tray 1  
   Single Sheet Feeder  
   Loading the Single Sheet Feeder  
   Using the Single Sheet Feeder  
   Using the Manual Duplex Function  
   Manual Duplex Printing from Tray 1...

   
2. Adjust the paper guides so they rest against the edges of the paper.  
 
 
   
3. Before loading the print media, flex the sheets back and forth, and then fan them. Straighten the edges of the stack on a level surface.  
 
 
   
4. Place the print media into the tray with the recommended print side face up.  
 
5. Adjust the width guides until they rest lightly against the edges of the stack of paper.  
 
 
   
6. After confirming that the guides are securely adjusted, insert the tray into the...

Loading the Envelope  
   
To load an envelope in Tray 1, load envelopes with the flaps closed when the short - edges of the envelopes enter the printer, or with the flaps open when the 
long - edges of the envelopes enter the printer.  
Single Sheet Feeder  
Capacity  
   
The single sheet feeder can hold:  
   
l 1 sheet of the standard paper.  
 
Print Media Dimensions  
   
The single sheet feeder accepts print media within the following dimensions:  
   
l Width  -  76.2 mm (3.00 inches) to 220.0 mm...

Loading the Envelope  
   
To load an envelope in the single sheet feeder, insert the envelope with the flap closed when the short edge of the envelop e faces into the printer. Place the 
envelope with the print side facing down and slide the envelope into the entry slot.  
 
   
Using the Single Sheet Feeder  
   
l Insert an envelope with the flap side face down and with the stamp area on the top right side.  
 
     
l Load letterhead face - down, with the top of the sheet entering the printer first....

Manual Duplex Printing from Tray 1  
Setting Method for Manual Duplex from Tray 1  
   
When you start manual duplex printing, the instruction windows appears. Note that you cannot display this window again if you close the window. Do not 
close the window until duplex printing is complete.  
1. First print the even pages. For a six page document, even pages are printed in the order page 6, page 4, then page 2.  
The  Continue  button blinks when the even pages finish printing.  
 
 
   
2. Next stack...

 
   
2. After the even pages have finished printing out, stack the prints and turn the stack over.  
 
 
   
3. Next print the odd pages. One sheet at a time, set the very top print that was turned over as it is with the blank side face down, then press the 
Continue button. Print pages in the order page 1 (rear of page 2), page 3 (rear of page 4), then page 5 (rear of page 6).  
 
Example: When duplex printing a four page document onto two sheets.  
Set one page at a time in the manual feed tray in the...