D-Link Router DHP-1565 User Manual

							46
D-Link DHP-1565 User Manual
Section 3 - Configuration
However,  if  the  automatic  detection  fails,  the  user  will  be  prompt  to 
either Try again or to click on the  Guide me through the IPv6 settings 
button to initiate the manual continual of the wizard.
There are several connection types to choose from. If you are unsure 
of your connection method, please contact your IPv6 Internet Service 
Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE 
client software on your computers has been removed or disabled. The 3 
options available on this page are  IPv6	over 	PPPoE, 	Static 	IPv6 	address	
and	Route,	and	 Tunneling	Connection.
Choose  the  required  IPv6  Internet  Connection  type  and  click  on  the 
Next  button  to  continue.  Click  on  the  Prev  button  to  return  to  the 
previous  page.  Click  on  the  Cancel button  to  discard  all  the  changes 
made and return to the main page.  
						

							47
D-Link DHP-1565 User Manual
Section 3 - Configuration
After  selecting  the  IPv6  over  PPPoE  option,  the  user  will  be  able  to 
configure the IPv6 Internet connection that requires a username and 
password to get online. Most DSL modems use this type of connection.
The following parameters will be available for configuration:
PPPoE Session:
Username:Password:
Verify Password: Service Name: Select the PPPoE Session value used here. This option 
will state that this connection shares it’s information 
with the already configured IPv6 PPPoE connection, 
or the user can create a new PPPoE connection here.
Enter the PPPoE username used here. If you do not 
know your user name, please contact your ISP.
Enter  the  PPPoE  password  used  here.  If  you  do  not 
know your password, please contact your ISP.
Re-enter the PPPoE password used here.
Enter the service name for this connection here. This 
option is optional.
Click  on  the 
Next  button  to  continue.  Click  on  the 
Prev button to return to the previous page.
 
Click on the  Cancel button to discard all the changes 
made and return to the main page.
IPv6
IPv6 over PPPoE  
						

							48
D-Link DHP-1565 User Manual
Section 3 - Configuration
This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your
IPv6 configuration settings. You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server, and Secondary DNS
Server. Your ISP provides you with all this information.
Use Link-Local Address:
IPv6 Address: Subnet Prefix Length:
Default 
Gateway:
Primary IPv6 
DNS Address:
Secondary IPv6  DNS Address:
LAN IPv6 Address: The  Link-local  address  is  used  by  nodes  and  routers 
when  communicating  with  neighboring  nodes  on  the 
same  link. This  mode  enables  IPv6-  capable  devices  to 
communicate with each other on the LAN side.
Enter the WAN IPv6 address for the router here.
Enter the WAN subnet prefix length value used here.
Enter the WAN default gateway IPv6 address used here.
Enter the WAN primary DNS Server address used here.
Enter the WAN secondary DNS Server address used here.
These are the settings of the LAN (Local Area Network) IPv6 interface for the router. The router’s LAN IPv6 Address configuration is 
based on the IPv6 Address and Subnet assigned by your ISP. (A subnet with prefix /64 is supported in LAN.)
Click on the Next button to continue. Click on the Prev button to return to the previous page.
Click on the Cancel button to discard all the changes made and return to the main page.
IPv6
Static IPv6  
						

							49
D-Link DHP-1565 User Manual
Section 3 - Configuration
After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings.
The following parameters will be available for configuration:
6rd IPv6 Prefix:
IPv4 Address:
Assigned IPv6 Prefix:
6rd Border Relay IPv4 Address:
IPv6 DNS Server: Enter the 6rd IPv6 address and prefix value used here.
Enter the IPv4 address used here.
Displays the IPv6 assigned prefix value here.
Enter the 6rd border relay IPv4 address used here.
Enter the primary DNS Server address used here.
Click on the Next button to continue. Click on the Prev button to return to the previous page.
Click on the Cancel button to discard all the changes made and return to the main page.
The IPv6 Internet Connection Setup Wizard was completed.
Click on the Connect button to continue. Click on the  Prev button to 
return to the previous page. 
Click on the  Cancel button to discard all the changes made and return 
to the main page.
IPv6
Tunneling Connection (6rd)  
						

							50
D-Link DHP-1565 User Manual
Section 3 - Configuration
Displays  the  LAN  IPv6  Link-Local  address  of  the 
router.
LAN IPv6 Address 
Settings:
IPv6
Link-local Only
Select  Link-local  Only  from  the My  IPv6  Connection  is   drop-down 
menu  if  your  Router  will  use  the  IPv6  link  local  method  to  connect  to 
the Internet.
Click the Save Settings button to save any changes made.  
						

							51
D-Link DHP-1565 User Manual
Section 3 - Configuration
There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6), PPPoE, IPv6 in IPv4 Tunnel,
6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled.
IPv6 Manual Setup
Auto Detection
Select  Auto Detection to have the router detect and automatically 
configure your IPv6 setting from your ISP. Click Manual IPv6 Internet Connection Setup to begin.  
						

							52
D-Link DHP-1565 User Manual
Section 3 - Configuration
Static IPv6
Select Static IPv6 from the drop-down menu.
Enter the address settings supplied by your Internet provider (ISP). 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select  Stateful (DHCPv6) , SLAAC + RDNSS  or SLAAC + Stateless DHCPv6 . 
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
WAN IPv6 Address Settings: LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconfiguration: Autoconfiguration Type:
IPv6 Address Range Start: IPv6 Address Range End: IPv6 Address Lifetime:  
						

							53
D-Link DHP-1565 User Manual
Section 3 - Configuration
Autoconfiguration
Select Autoconfiguration (Stateless/DHCPv6) from the drop-down menu.
Select either  Obtain DNS server address automatically  or Use the following 
DNS Address.
Enter the primary and secondary DNS server addresses. 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.  
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
IPv6 DNS Settings:
Primary/Secondary DNS  Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconfiguration: Autoconfiguration Type:
IPv6 Address Range Start: IPv6 Address Range End: IPv6 Address Lifetime:  
						

							54
D-Link DHP-1565 User Manual
Section 3 - Configuration
PPPoE
Select PPPoE from the drop-down menu.
Enter the PPPoE account settings supplied by your Internet provider (ISP). 
Select  Static if your ISP assigned you the IP address, subnet mask, gateway, 
and DNS server addresses. In most cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the next box.
Enter the ISP Service Name (optional).
Select either Always-on, On-Demand, or Manual.
Enter  a  maximum  idle  time  during  which  the  Internet  connection  is 
maintained during inactivity. To disable this feature, enable Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal 
performance with your specific ISP. 1492 is the default MTU.
Select  either  Obtain  DNS  server  address  automatically   or Use  the 
following DNS Address.
Enter the primary and secondary DNS server addresses. 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
My IPv6 Connection:
PPPoE:
Address Mode:
IP Address:
User Name: Password:
Service Name:
Reconnection Mode: Maximum Idle Time: 
MTU:
IPv6 DNS Settings:
Primary/Secondary DNS  Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconfiguration:  
						

							55
D-Link DHP-1565 User Manual
Section 3 - Configuration
Autoconfiguration Type:
IPv6 Address Range Start: IPv6 Address Range End: IPv6 Address Lifetime: Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the IPv6 Address Lifetime (in minutes).